“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

Various density light field image coding based on distortion minimization interpolation

In recent years, the light field (LF) as a new imaging modality has attracted wide interest. The large data volume of LF images poses great challenge to LF image coding, and the LF images captured by different devices show significant differences in angular domain. In this paper we propose a view prediction framework to handle LF image coding with various sampling density. All LF images are represented as view arrays. We first partition the views into reference view (RV) set and intermediate view (IV) set. The RVs are rearranged into a pseudo sequence and directly compressed by a video encoder. Other views are then predicted by the RVs. To exploit the four dimensional signal structure, we propose the linear approximation prior (LAP) to reveal the correlation among LF views and efficiently remove the LF data redundancy. Based on the LAP, a distortion minimization interpolation (DMI) method is used to predict IVs. To robustly handle the LF images with different sampling density, we propose an Iteratively Updating depth image based rendering (IU-DIBR) method to extend our DMI. Some auxiliary views are generated to cover the target region and then the DMI calculates reconstruction coefficients for the IVs. Different view partition patterns are also explored. Extensive experiments on different types LF images also valid the efficiency of the proposed method.     

Large eddy simulation of flow over square cylinder arrays in an octagonal configuration at subcritical Reynolds numbers

In this study, fluid flow over an array of eight, 0.029 m × 0.029 m, square cross‐section cylinders in an octagonal configuration is studied numerically. The mean force coefficients (drag and lift) and the vortex formation characteristics of the array are calculated numerically by utilizing a three‐dimensional large eddy simulation mathematical model for turbulence. The numerical simulation is performed with commercial software ANSYS Fluent 19R1. To investigate the parametric influences, three spacings between the cylinders (0.07, 0.14, and 0.2 m), two array attack angles (0° and 15°), and two Reynolds numbers (4060 and 45 800) are considered. The results comprise flow patterns and force coefficients' variations with Reynolds numbers. The lift force of the downstream cylinder reaches its maximum at α = 15°, and the drag force of the upstream cylinders finds its peak at α = 0°. It is observed through velocity and viscosity contour plots that vortex formation length near the cylinder increases at higher Reynolds number. Velocity vector plots are also presented to show fluid flow behavior near the cylinder. Furthermore, the predicted mean forces on the cylinders are slightly different for different Reynolds numbers, spacings, and angles of attack.     

Differences between oculomotor and perceptual artifacts for temporally limited head mounted displays

We used perceptual and oculomotor measures to understand the negative impacts of low (phantom array) and high (motion blur) duty cycles with a high‐speed, AR‐likehead‐mounted display prototype. We observed large intersubject variability for the detection of phantom array artifacts but a highly consistent and systematic effect on saccadic eye movement targeting during low duty cycle presentations. This adverse effect on saccade endpoints was also related to an increased error rate in a perceptual discrimination task, showing a direct effect of display duty cycle on the perceptual quality. For high duty cycles, the probability of detecting motion blur increased during head movements, and this effect was elevated at lower refresh rates. We did not find an impact of the temporal display characteristics on compensatory eye movements during head motion (e.g., VOR). Together, our results allow us to quantify the tradeoff of different negative spatiotemporal impacts of user movements and make subsequent recommendations for optimized temporal HMD parameters.     

Synthesizing a uniformly spaced array pattern using integral operator for removing progressive phase shift

In this article, an analytical technique is introduced to obtain the excitation coefficients of uniformly spaced linear antenna arrays in order to achieve a desired array factor. By integration of the prescribed array factor, the array factor dependency to the progressive phase shift is eliminated. A new system of linear equations is consequently obtained whose solution represents the excitation coefficients of the array. Some examples are presented to verify the accuracy of the introduced method. The performance of this strategy is compared with those obtained by the other well‐known techniques such as Woodward‐Lawson and Fourier transform. It is shown that the presented method estimates the desired array pattern with a very good precision.     

基于改进型巴特勒矩阵的短波8元圆环阵列多波束技术研究

传统短波接收天线为单一的波束指向天线或全向天线。为提高接收天线增益,同时产生多个波束指向不同方向,提出利用巴特勒矩阵作为短波接收天线阵的无源波束形成网络。在传统8×8巴特勒矩阵结构的基础上,设计改进型8×8巴特勒矩阵。以均匀8元圆环阵列为天线模型,利用FEKO仿真分析了其天线特性。在3~11 MHz频段内,P2、P3、P6、P7四个端口分别在202.5°、292.5°、112.5°、22.5°方向上得到了方向性较强的单一波束,7 MHz时波束增益达到最大11.9 dBi,波瓣3 dB宽度平均为60°;在P1、P4、P5、P8端口产生相同的2个波瓣,7 MHz时其波束增益达到最大9.8 dBi,波瓣3 dB宽度平均为89°。由以上仿真分析得出,该改进型8×8巴特勒矩阵能够同时产生6个波束,波束覆盖8个方向,提高了波束的方向性,提高了天线增益。     

用宽带超表面产生阵列贝塞尔光束

通过在空间光调制器（SLM）上加载相位图或通过光刻加工微型圆锥状结构可以产生贝塞尔光束阵列。然而，典型空间光调制器具有比波长大一个数量级的像素尺寸，这限制了相位梯度的可用范围，用光刻法加工的微型锥透镜的顶端不是标准的圆锥，这影响了贝塞尔光束的质量。为了克服这些缺点，将复杂的相位图加载到电介质超表面上，设计了一种可以产生阵列贝塞尔光束（在波长700 nm处，NA=0.3）的超表面器件。该器件可以宽波段工作，其单元结构在波长580~800 nm范围内的偏振转换效率均超过57%。利用时域有限差分算法（FDTD）对该器件（厚度为380 nm，直径仅为40 μm）进行了仿真，所产生的阵列光束都垂直于超表面器件。所提出的阵列贝塞尔光束发生器具有纳米级别的厚度和几十微米的直径，这对于未来的集成光学领域具有很大的应用前景。     

Up-pulling force analysis for ESC hollow cylindrical casting

Electroslag casting(ESC)is an important method to produce high quality castings.In this study,the ESC up-pulling inner mold method(EUPIM)was used to produce hollow cylindrical castings with the multiple consumable electrodes.The radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell were analyzed using the finite element method(FEM)with the aid of ANSYS software.The ProCAST software was used to calculate the specific heat,heat conductivity and density curve of Cu.Simulation results show that the radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell near the slag-metal interface of hollow cylndrical casting gradually increase from 0 s to 360 s after the ESC starting(slagging)process but before applying the up-pulling force.The suitable initial up-pulling moment of the inner mold is at around 180-198 s after the starting process.     

微间隙共形圆柱接触力模型的适用性分析

针对目前间隙铰接副接触力模型无法有效表述不同材料耗散阻尼效应,以及不适用于微间隙共形接触的问题,分析各种接触力模型中弹性接触力和耗散阻尼力计算方法的优缺点,提出一种普适性的圆柱内接触力分析模型。该模型将接触力描述为接触深度的显式函数,并将其适用范围有效地扩展至微间隙和低恢复系数工况。采用含间隙铰接副的曲柄-滑块机构进行动力学分析,对所提出接触力进行验证,计算结果表明:所提出的普适性接触力模型体现了微间隙时更高的接触刚度和低恢复系数时显著的阻尼效应,从而可为不同材料和间隙尺寸的间隙铰接副力学分析提供更为完备的计算模型。     

Fabrication of 3D Ni nanosheet array on Crofer22APU interconnect and NiO-YSZ anode support to sinter with small-size Ag nanoparticles for low-temperature sealing SOFCs

A novel low-temperature sealing method was developed to seal solid oxide fuel cells. The 3D Ni nanosheet array was pre-fabricated on faying surfaces of Crofer22APU interconnect and NiO-YSZ anode-support. Then it was covered with Au film without changing its morphology. This special nanostructure improved sintering efficiency between Ag nanoparticles and substrates. A dense joint was obtained at the low-temperature between 250 °C–300 °C. This method effectively avoided the oxidation of interconnect during sealing. When joints were sealed at 300 °C, the shear strength reached 16 MPa. The fracture was mainly located in the central Ag layer, presenting a significant plastic deformation. Due to the effective protection of Ni layer, joints also possessed excellent oxidation resistance in oxidizing atmosphere at 800 °C for 400 h. After high-temperature oxidation, the shear strength was increased to 23 MPa, revealing an increasement of 43.8% compared with the as-sealed condition (16 MPa). This sealing method has great potential in sealing solid oxide fuel cells. It also can be extended to seal other energy-conversion devices.