聚乙烯催化剂用烷氧基镁载体的研究进展

基于烷氧基镁载体的Ziegler-Natta聚乙烯催化剂具有活性高、氢调性能好等优点,是目前聚烯烃工业中的研究热点。介绍了烷氧基镁载体的发展进程,综述了烷氧基镁载体的制备及改进方法,分析了烷氧基镁载体在催化剂制备过程中的作用,并对开发适用于乙烯聚合的烷氧基镁载体提出了展望。     

Facile access to carboxyl-terminated polybutadiene and polyethylene from cis-polybutadiene rubber

Carboxyl-terminated polybutadiene (CTPB) is a widely used telechelic liquid rubber, which is mainly prepared by anionic or free-radical polymerization of 1,3-butadiene. It is known that the microstructure of liquid polybutadiene rubber largely affects its processability and mechanical properties. However, it is hard to control its microstructure in the free radical or anionic polymerization. In this study, a series of CTPB with high cis-1,4 content has been prepared for the first time via the oxidolysis and selective oxidation of cis-polybutadiene rubber (BR). Hydrogenation of their CC double bonds with p-toluenesulfonyl hydrazide/tri-n-propylamine (TSH/TPA) reagents afforded carboxyl-terminated polyethylenes (CTPE). For comparison, commercial CTPB (FCTPB), prepared by free-radical polymerization of 1,3-butadiene, was also hydrogenated and gave FCTPE with more ethyl branches. Linear CTPE (L-CTPE) was synthesized by ring-opening metathesis polymerization of 1,5-cyclooctadiene in the presence of maleic acid and subsequent hydrogenation. The microstructure of the polymers was established by FT-IR, ¹H NMR, ¹³C NMR, and GPC and their thermal properties were determined by DSC and TGA. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46934.     

Poly(L-lysine)-poly(ethylene glycol) layers with different structure and their influence on silica suspension stability

The effects of the structure of di- and triblock copolymers of poly(L-lysine) – LYS with poly(ethylene glycol) – PEG as well as the length of nonionic fragment in the LYS-PEG macromolecule on the copolymer chains conformation in the adsorption layer formed on the colloidal silica (SiO2) surface were examined. Spectrophotometry and turbidimetry were applied for the determination of copolymer adsorbed amounts and stability coefficients of silica aqueous suspensions. The electrokinetic parameters such as solid surface charge density and zeta potential were also estimated. The adsorption of LYS-PEG was proved to be the highest at pH 10 whereas the lowest adsorption on the solid surface was found for the triblock copolymer with long fragments of LYS at the same pH value.     

Improved compatibility of PET/HDPE blend by using GMA grafted thermoplastic elastomer

ABSTRACT

Herein, graft-modified ethylene-1-octene copolymer (POE-g-GMA) and styrene-butadiene-styrene triblock copolymer (SBS-g-GMA) were found to be excellent reactive compatibilizers for immiscible poly(ethylene terephthalate) (PET)/high-density polyethylene (HDPE) blends via in-situ reaction compatibilization. With increase in compatibilizer amount, uniform phase morphology was observed in all the blends. Thus, exhibiting enhanced mechanical properties, especially, the notched Izod impact strength. In comparison with SBS-g-GMA, compatibilizer POE-g-GMA demonstrated greater impact on the compatibility. The addition of 15% POE-g-GMA produced blends with best mechanical properties. Besides, both POE-g-GMA and SBS-g-GMA enhanced the melt viscosity of PET/HDPE blends.     

核电厂聚乙烯管道设计方法及标准简介

随着聚乙烯管道在三门核电厂、大亚湾核电厂中的试应用成功，大量的新建核电厂及核电厂改造项目均将聚乙烯管道作为海水冷却水管道系统的首选管材，自主研制核电厂聚乙烯管技术标准迫在眉睫。本文介绍了核电聚乙烯管道的发展历史和应用现状，对比了核安全3级聚乙烯管道和非核安全相关聚乙烯管道、城市燃气与给水聚乙烯管道技术标准的设计方法及适用范围，探讨了中国目前聚乙烯管技术标准与核3级聚乙烯管道技术标准的差异与差距，为核电厂聚乙烯管道的设计制造与标准研制提供参考。     

纳米氧化锌/低密度聚乙烯膜中锌向食品的迁移研究

目的研究纳米氧化锌/低密度聚乙烯膜(low density polyethylene film,LDPE)中锌(Zn)向食品的迁移行为,探究其迁移规律。方法选取2种食品模拟物(3%乙酸及超纯水)及真实食品(食用白醋及瓶装水),在3种不同实验温度下(70、40及20℃),研究锌向食品模拟物的迁移规律。采用扫描电子显微镜(scanning electron microscope,SEM)和原子力显微镜(atomic force microscope,AFM)表征纳米ZnO/LDPE膜的表面形貌。结果锌向酸性模拟物中的迁移率远远大于水性模拟物中的迁移率,其中锌向酸性模拟物中的最大迁移率分别为22.7%,20.3%及18.6%(ZL-1,ZL-2及ZL-2#),向水性模拟物中的最大迁移率分别为9.9%,5.7%及4.9%(ZL-1,ZL-2及ZL-2#);锌向酸性食品的迁移量(1.59~5.03 mg/g)同样高于向水性食品的迁移量(2.98~24.60μg/g);随着纳米ZnO的初始含量变大迁移率变小;而偶联剂的加入对锌的迁移有一定的抑制作用。随着纳米ZnO浓度的增加,在薄膜中观察到纳米ZnO的不规则形貌。结论纳米ZnO/LDPE膜不适合在高温下包装食物,且其在酸性食品中的安全隐患高于水性食品。     

65号航空冷却液的泡沫倾向性研究

针对65号航空冷却液在过滤循环中出现泡沫较多的现象，对65号航空冷却液泡沫倾向性进行探究。按照石化行业标准《发动机冷却液泡沫倾向测定法（SH /T 0066-2002）》，利用冷却液泡沫倾向测定仪来评价65号航空冷却液泡沫倾向性，并进行水乙二醇溶液对照试验。结果表明，航空冷却液在低温和循环时间较长的情况下，其泡沫倾向性较大，而随着温度的升高和循环时间的缩短，泡沫倾向性有一定程度的改善；并且通过水乙二醇对照试验可知，冷却液的基础液泡沫倾向性较小。航空冷却液在过滤循环中出现的泡沫问题，是加入的添加剂所引起的。     

利用KH560和纳米SiO2采用“一步法”反应挤出增黏PET

以KH560（3-缩水甘油基氧基丙基三甲氧基硅烷）和纳米SiO₂颗粒复配作为扩链剂，采用“一步法”反应挤出增黏聚对苯二甲酸乙二醇酯（PET）。KH560和SiO₂的添加量均为PET质量分数的2.5%时，增黏效果最好。并且在PET不干燥的情况下，KH560和SiO₂复配也可增加PET的黏度，可用作PET的扩链剂和防水解剂。经透射电镜观察，发现SiO₂在PET中的分散状况良好。用FTIR研究了KH560、SiO₂、PET三者之间的反应机理。用TGA分析了SiO₂的接枝率，发现接枝率高达72.0%。用DSC对PET/纳米SiO₂复合材料的结晶行为进行了研究，并讨论了结晶行为对力学性能的影响。当KH560和SiO₂的添加量均为PET质量分数的2.5%时，结晶度最低，综合力学性能最好。     

亲水性PET共混材料的制备及性能研究

以机械共混法制备亲水性聚对苯二甲酸乙二醇酯（PET）共混材料，并通过接触角测定仪、差示扫描量热仪(DSC)和电子万能材料试验机等对共混材料的亲水性能、热性能和力学性能等进行研究与分析。结果表明，亲水处理剂聚乙二醇（PEG）、聚丙烯酸钠（PAAS）、聚乙烯吡咯烷酮（PVP）均能改善PET的亲水性能，影响PET的结晶性能，但亲水处理剂对PET的力学性能影响较小，其中PET/PEG共混材料的亲水性最优；随着PEG含量的增加，PET/PEG共混材料的亲水性先逐渐增强，当PEG含量高于5 %后，共混材料的亲水性变化很小；且PET的结晶度随着PEG的加入呈现先增大后减小的趋势。