Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.     

红外菲涅尔透镜的注射超声辅助成型优化

为了提升聚合物红外菲涅尔透镜的光学性能,以其表面微沟槽的成型质量为目标,提出了一种高效的注射超声辅助成型方法,并对工艺参数进行了综合质量优化。首先分析了超声振动对聚合物的加热和加压效应,设计了一套一模两腔的对比试验模具;接着以红外菲涅尔透镜的调制传递函数MTF和齿形平均高度h为优化质量目标,设计了四步骤的多目标优化流程,通过试验设计、基于BP神经网络的质量目标与注射工艺参数关系建模、基于NSGA-Ⅱ的多目标优化和试验验证进行工艺参数的综合优化。实验结果表明:该多目标优化流程具有很高的精度,MTF和h的平均预测误差MPE分别为4.16%和3.32%;注射超声辅助成型的菲涅尔透镜微沟槽具有更高的复制质量,其齿沟槽平均高度h增加了15.6%,且h值的波动量随着h值的增大而增大,MTF值受齿高h均匀性的影响大于齿高h对其的影响。     

Pregnancy by Assisted Reproductive Technology Is Associated with Shorter Telomere Length in Neonates

Telomere length (TL) influences the development of lifestyle-related diseases, and neonatal TL may influence their prevalence. Various factors have been reported to affect neonatal TL. Although the fetus is exposed to multiple conditions in utero, the main factors affecting the shortening of neonatal TL are still not known. In this study, we sought to identify factors that influence fetal TL. A total of 578 mother-newborn pairs were included for TL analysis. TL was measured in genomic DNA extracted from cord blood samples using quantitative PCR. The clinical factors examined at enrollment included the following intrauterine environmental factors: maternal age, assisted reproductive technology (ART) used, body mass index (BMI), gestational diabetes mellitus (GDM), maternal stress, smoking, alcohol consumption, preterm delivery, small-for-gestational-age, neonatal sex, and placental weight. Univariate and multivariate regression analyses were used to verify the relationship between neonatal TL and these clinical factors. The median neonatal TL to single-copy gene ratio was 1.0. Pregnancy with ART was among the 11 factors associated with shorter neonatal TL. From multiple regression analysis, we determined that neonatal TL was significantly shorter for pregnancies in the ART group than in the other groups. We conclude that pregnancy with ART is associated with shorter neonatal TL.     

Relations between asphaltene content,viscosity reduction rate of heavy oil and ultrasonic parameters

Ultrasonic treatment could decrease the viscosity of heavy oil and previous study on had focused on one heavy oil sample and involved less on the influence of asphaltene content. This study examined the effect of asphaltene content on viscosity reduction rate by ultrasonication. A comparison on samples with various asphaltene content and vibration parameter was made. The results showed that the optimal vibration frequency might decrease as the asphaltene content increased, whereas the optimal vibration intensity and the optimal treatment time were suggested to be enlarged. A semi-quantitative correlation was matched, which helped for numerical simulation about ultrasonic treatment.     

超声波解冻与传统解冻方式的比较与竞争力评估

超声波解冻通过空化效应、机械效应和热效应对冷冻食品进行解冻,解冻效率高、对冷冻食品的损伤较小。该文简要介绍了空气解冻、水解冻和电解冻的解冻机制及研究进展,详细阐述了超声波解冻的机制及研究进展。将超声波解冻与空气解冻、水解冻和电解冻进行对比,发现超声波解冻的解冻效率最优,且将超声波与这3种传统解冻方式结合可以提高解冻效率,并且获得更好的解冻效果。超声波频率和强度以及冻结食品的解冻温度是影响解冻效果的主要参数。超声波在食品中的衰减程度受到解冻温度的影响极大,因此在调节超声波频率和强度同时调控解冻温度对解冻效果至关重要。     

对于厚度70mm〜140mm焊缝超声检测的讨论

超声检测作为一种面积型缺陷的有效检测方法,被广泛应用在气化炉、除氧器、汽包等的焊缝检测上。随着近年来电厂、化工厂对质量的要求提升,确保焊缝质量就成了生产制造厂的重点。对于这些重型容器,焊缝厚度普遍在70mm~140mm,在这个厚度区间,采取的多道焊接,工艺控制不严很容易产生缺陷。无损检测标准的制定只是简单的对此厚度划分两个区间,并未给出划定此区间的依据。本文通过实际检测气化炉、除氧器、汽包等焊缝来讨论超声检测在厚度70mm?140mm区间的划定依据。     

超声提取-离子色谱法测定银精矿中水溶性氟

银精矿中水溶性氟会随雨水的冲刷进入生物圈,直接对土壤、水体、大气、人类健康产生危害。实验提出超声提取-离子色谱法测定银精矿中水溶性氟,为银精矿中水溶性氟的检测及后续环境影响评估提供重要的技术支撑。称取0.2g样品(过150目筛),加入30mL水,在40℃时超声提取20min后,使用阴离子交换柱进行分离,使用碳酸钠-碳酸氢钠混合溶液作为淋洗液进行淋洗,洗脱时间为25min,通过电导检测器进行F^-检测。F^-质量浓度在0.5~10mg/L范围内与对应的峰面积呈线性关系,校准曲线线性相关系数为0.9998;方法检出限为0.062mg/L,测定下限为0.21mg/L。按照实验方法测定两个银精矿中水溶性氟,测定结果的相对标准偏差(RSD,n=6)为3.8%和4.3%;加标回收率为92%~102%。