Effects of rice bran fermented with Lactobacillus plantarum on palatability,volatile profiles,and antioxidant activity of brown rice noodles

Brown rice noodles (RN) are typical whole-grain products with health benefits. This study investigated the effects of rice bran fermented with Lactobacillus plantarum on palatability, volatile profiles, and antioxidant activity of brown RN. Three kinds of RN, including RN, brown RN (BRN), and bran fermented RN (BFRN), were involved in this study. The results indicated that bran fermentation reduced the cooking loss of BFRN and improved the elongation and the sensory attributes of brown RN. After fermentation, aldehydes were significantly decreased while alcohols increased, and more pleasant flavours were shown in BFRN. Fermentation increased the content of free phenolics and decreased the content of bound phenolics. Among the four major phenolics detected in this study, ferulic acid was the most abundant one in all three RN samples. The DPPH radical scavenging activity and the ferric reducing antioxidant power of free phenolics in BFRN increased significantly compared to BRN. This study proved that rice bran fermentation is an effective approach to improve palatability, enrich the flavour as well as enhance the antioxidant activity of brown RN, which may facilitate the development of processing technology for brown RN.     

Parameter characterization of HTPEMFC using numerical simulation and genetic algorithms

This paper develops a novel approach to the parameterisation of high temperature exchange membrane fuel cells (HTPEMFC) with limited and non-invasive measurements. The proposed method allows an effective identification of electrochemical parameters for three-dimensional fuel cell models by combining computational simulation tools and genetic algorithms. To avoid each evaluation undertaken by the optimisation method involving a complete computational simulation of the 3D model, a strategy has been designed that, thanks to an iterative process, makes it possible to decouple the fluid dynamic resolution from the electrochemistry one.Two electrochemical models have been incorporated into these tools to describe the behaviour of the catalyst layer, Butler-Volmer and spherical aggregate. For each one, a case study has been carried out to validate the results by comparing them with empirical data in the first model and with data generated by numerical simulation in the second. Results show that, from a set of measured operating conditions, it is possible to identify a unique set of electrochemical parameters that fits the 3D model to the target polarisation curve. The extension of this framework can be used to systematically estimate any model parameter in order to reduce the uncertainty in 3D simulation predictions.     

Picosecond laser trimming of ceramic cores with porous multi-scale particle microstructure

The ceramic core, produced by hot injection molding, is one of the critical components for manufacturing high-performance aircraft engine turbine blades. However, the injection molding process will cause defects such as burrs and flashes in the fine structure of the formed ceramic core. Manual trimming is necessary, but the trimming quality is poor, and the yield is low. In this paper, the online trimming method of ceramic cores is studied. Based on the orthogonal experiment method, the optimal laser parameters for processing the ceramic core's porous multi-scale particle structure material were obtained. Further, the problems of the match head and tail phenomenon and dimensional accuracy improvement in trimming ceramic cores have been studied. A path optimisation method is proposed to improve the quality and accuracy of the trimming profile effectively. Finally, the overall process flow of ceramic core trimming is elaborated, and experimental verification is given. The results show that the ceramic core online trimming method proposed in this paper has advantages of high precision and high yield compared with the manual method, which will have substantial potential application value in the aviation field.     

Process knowledge-based random forest regression for model predictive control on a nonlinear production process with multiple working conditions

In process industry, predictive control approaches have been widely used for nonlinear production processes. Practically, the predictor in a predictive controller is extremely important since it provides future states for the optimization problem of controllers. The conventional predictive controller with precise mathematical predictors approximating the state space of physical systems is difficult and time-consuming for nonlinear production processes, and it performs poorly over a wide range of working conditions and with significant disturbances. To address the challenges, the trend of applying artificial intelligence emerges. However, the industrial process-specific knowledge is ignored in most cases. In this study, a predictive controller with a control process knowledge-based random forest (RF) model is proposed. Specifically, working data are clustered at first to handle diverse working conditions. Then, a process knowledge-based forest predictor, namely MIW-RF model with a redesigned cascading RF structure, is proposed to incorporate control process knowledge into modeling. Thus, future states of controlled variables could be more accurately acquired for the optimizer. A simplified version of the predictive model is also developed with quick model training and updating. The proposed predictive methods are finally introduced into the controller design. According to the empirical results, the proposed methods deliver a better control performance against benchmarks, including more accurate anticipated controlled-variable responses, better set-point tracking and disturbance rejection capability.     

Experimental study and model predictions on helium release in an enclosure with single or multiple vents

This paper presents experiments performed at Canadian Nuclear Laboratories (CNL) to examine the dispersion behaviour of helium in a polycarbonate enclosure that was representative of a residential parking garage. The purpose was to gain a better understanding of the effect of buoyancy- or wind-driven natural ventilation on hydrogen dispersion behaviour. Although hydrogen dispersion studies have been reported extensively in the literature, gaps still exist in predictive methods for hazard analysis. Helium, a simulant for hydrogen, was injected near the centre of the floor with a flow rate ranging from 5 to 75 standard litres per minute through an upward-facing nozzle, resulting in an injection Richardson number ranging between 10^?1 and 10². The location of the nozzle varied from the bottom of the enclosure to near the ceiling to examine the impact of the nozzle elevation on the development of a stratified layer in the upper region of the enclosure. When the injection nozzle was placed at a sufficiently low elevation, the vertical helium profile always consisted of a homogenous layer at the top overlaying a stratified layer at the bottom. To simulate outdoor environmental conditions, a fan was placed in front of each vent to examine the effect of opposing or assisting wind on the dispersion. The helium transients in the uniform layer predicted with analytical models were in good agreement with the measured transients for most tests. Model improvements are required for adequately predicting transients with primarily stratified profiles or strong opposing wind.     

Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently, which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure (EWP). By means of a three-dimensional (3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system (TDS) widely used in China and its optimized drainage system (ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice, including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 kPa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.     

Recent advances during CH4 dry reforming for syngas production: A mini review

Given the continuing issues of environment and energy, methane dry reforming for syngas production have sparked interest among researchers, but struggled with the process immaturity owing to catalyst deactivation. This review summarizes the recent advances in the development of efficient and stable catalysts with strong resistance to coking and metal sintering, including the application of novel materials, the assessment of advanced characterizations and the compatibility to improved reaction system. One feasible option is the crystalline oxide catalysts (perovskite, pyrochlore, spinel and LDHs), which feature a fine metal dispersion and surface confinement effect via a metal exsolution strategy and exhibit superior reactivity and stability. Some new materials (h-BN, clays and MOFs) also extend the option because of their unique morphology and microstructure. It also is elaborated that progresses were achieved in advanced characterizations application, leading to success in the establishment of reaction mechanisms and attributions to the formed robust catalysts. In addition, the perspective described the upgrade of reaction system to a higher reaction efficiency and milder reaction conditions. The combination of efficient reaction systems and robust catalysts paves a way for a scaling-up application of the process.     

Development of structurally modified OER catalysts with enhanced performance and longevity for PEM-based electrolytic air dehumidification

PEM-based electrolytic air dehumidification is innovative in dehumidification that requires high precision and small space due to its high efficiency, compactness, and cleanness. However, the system dehumidification performance and durability are limited by using commercial Anatase-IrO₂ catalysts. In this study, two types of structurally modified OER catalyst materials, ATO-IrO₂ and ND-MnO₂-IrO₂, are developed to improve the performance of the system. System experiments showed that, compared to the commercial catalysts, the use of ATO-IrO₂ and ND-MnO₂-IrO₂ as the anode catalyst can improve the dehumidification performance by 45% and 20%, respectively. Furthermore, in 50-h accelerated aging tests, the attenuation rates of the ATO-IrO₂ and ND-MnO₂-IrO₂ systems are 3% and 8% respectively, which are far lower than the 35% attenuation of commercial catalyst. The results indicate that, as catalysts with a classic core-shell structure, ATO-IrO₂ and ND-MnO₂-IrO₂ still have a significant impact on improving the performance of the electrolytic dehumidification systems.