地应力条件下的凿岩爆破数值模拟

为了研究地应力对凿岩爆破的影响,采用DDA方法模拟爆炸应力波作用下考虑地应力条件时的单孔和多孔凿岩爆破破岩过程。模拟发现,随着初始地应力水平的增加,裂纹扩展半径和破岩区域面积减小,裂纹发育主方向趋于地应力的最大主应力方向,初始地应力对裂纹的抑制和引导作用明显;初始地应力水平的增加,对拉伸裂纹的抑制作用更为显著,从而降低了拉伸破坏对爆破破岩的贡献。模拟也表明,在初始地应力存在的条件下,通过对爆破载荷和炮孔布置进行针对性的优化,可以克服地应力带来的影响,并取得预期的爆破效果。本研究对地应力条件下的凿岩爆破工程具有理论和参考意义。     

建筑结构控制爆破拆除的力学分析与应用

应用运动学、动力学理论建立建(构)筑物控爆坍落过程的力学模型,进而研究在非定常约束条件下坍落结构的力学特征。首次提出了采用延时起爆技术时,非自由质点系及其广义坐标应是建立在每一段位上的瞬间虚位移。在此基础上,分析求解运动过程中时控单元的质点自由度,为精确选定爆破部位及时序提供了设计理论和计算依据。同时,结合振动理论,将控爆时差、结构载荷分布调制为振动系统,形成坍落结构梁板单元的强迫振动,充分实现在运动中进一步解体、破碎其自身结构,并形成具有明显缓冲效果的下落过程。应用实践结果证明力学分析是正确的,为工程结构爆破拆除计算机辅助设计及动态模拟技术的有效应用奠定了基础。     

基于FLAC3D的破碎围岩巷道支护效果分析

为了解破碎围岩分别采用锚杆支护、锚喷支护以及锚喷+锚索耦合三种支护方式下的支护效果,进而为破碎围岩巷道选择合理的支护方式提供参考。通过借助FLAC^3D软件建立数值模型,分析不同支护条件下的破碎围岩巷道位移量、应力分布以及塑性区的时空演化特征。结果表明,采用锚喷+锚索耦合支护时,可以较好的控制巷道围岩的位移量、减小应力集中效应、缩小塑性区的影响范围。     

Strength and deformation properties of frozen sand under a true triaxial stress condition

In recent years, the mechanical properties of frozen soils under complex stress states have attracted significant attention; however, limited by the test apparatus, true triaxial tests on frozen soils have rarely been conducted. To study the strength and deformation properties of frozen sand under a true triaxial stress state, a novel frozen soil testing system, i.e., a true triaxial apparatus, was developed. The apparatus is mainly composed of a temperature control system, a servo host system, a hydraulic servo loading system, and a digital control system. Several true triaxial tests were conducted at a constant minor principal stress (σ₃) and constant intermediate principal stress ratio (b) to study the effect of intermediate principal stress (σ₂) on the mechanical properties of frozen sand. The test results showed that the stress–strain curve can be mainly divided into three stages, with evidence of strain hardening characteristics. The strength, elastic modulus, and friction angle increased with the increase in b from 0 to 0.6, but decreased when increasing b from 0.6 to 1, whereas the cohesion varied little with the variation in b. The deformation in the direction of σ₂ changed from dilative to compressive and that in the direction of σ₃ remained dilative throughout.     

Stability assessment of 3D reinforced soil structures under steady unsaturated infiltration

Internal stability assessment of geosynthetic-reinforced soil structures (GRSSs) has been commonly carried out assuming plane-strain conditions and dry backfills. However, failures of GRSSs usually show three-dimensional (3D) features and occur under unsaturated conditions. A procedure based on the kinematic limit-analysis method is proposed herein to assess 3D effects and the role of steady unsaturated infiltration on the required geosynthetic strength for GRSSs. A suction stress-based framework is used to describe the soil stress behavior under steady unsaturated infiltration. Based on the principle of energy-work balance, the required geosynthetic strength is determined. A comparison analysis with the prior research is conducted to verify the developed method. Two kinds of backfills, i.e., high-quality backfill and marginal backfill, are considered for comparison in this work. It is shown that accounting for 3D effects and the role of unsaturated infiltration considerably reduces the required geosynthetic strength. The 3D effects are primarily affected by the width-to-height ratio of GRSSs, and the contribution of unsaturated infiltration is mainly influenced by the soil type, flow rate, GRSS's height, and location of the water table.     

A comparison of shear stress estimation methods for a single geobag on a rough bed

There are several methods for estimating bed shear stress in the literature, but comprehensive comparisons among them are limited and under specific conditions. This study compared these methods first on a bare smooth bed, and then for a single geobag on a rough bed in the interest of determining the stability of geobags used in riverbank protection structures. The geobag was filled with cement or sand and tested under different open channel flow conditions. The turbulent kinetic energy method appeared to best represent the local bed shear stress on the geobag when using the newly calibrated proportionality constants. The Reynolds stress method via extrapolation was relatively unaffected by changes to the geobags shape and measurement locations, suggesting this method inadequately represents the local bed shear stress. The Patel method and the universal law of the wall method failed to represent local bed shear stress in the rough bed cases due to instrument limitations and the breakdown of the law of the wall. This study highlights the impact of different methods on the bed shear stress estimation.     

建筑物掏土纠倾法单孔与多孔塑性区特性研究及工程应用

在建筑物水平掏土纠倾工程中，掏土孔间距是影响纠倾工程安全与工期的重要因素。为了快速准确地确定纠倾工程中的水平掏土孔间距，研究了单个掏土孔和多个掏土孔情况下孔周边土体塑性区发展特性。利用土体塑性力学分析计算得到了单孔下的孔周土塑性区半径，而后通过有限元模拟得到孔周土体塑性区半径的数值解，将孔周塑性区半径解析解与数值解进行了对比。并通过有限元数值模型研究了多个掏土孔相互影响情况下的塑性区发展规律，以孔间土体塑性区贯通时的距离作为掏土孔间距。考虑土体参数随机特性的影响，研究不同上部荷载作用下掏土孔间距的取值变化规律，上部面荷载与地基承载力特征值比值用p表示，孔间距与掏土孔直径比值用n表示。研究发现：多孔塑性区半径（孔间塑性区贯通时）是单孔塑性区半径的1.3倍左右;标准化荷载p与孔间距比值n二者呈线性关系;通过不同土体参数及上部荷载的不同情况下的p-n曲线，给出了掏土孔间距建议值。同时，将研究结果与三个实际工程进行对比，发现p-n曲线法与实际结果更为接近。     

Experimental study and numerical modeling of mixing by air injection in yield stress fluids using the OpenFOAM software

Mixing by gas injection is an operation used in industrial processes such as wastewater treatment, metallurgy, or methanization in which pressurized gas is injected into a fluid in order to reduce concentrations and temperatures gradients. This study demonstrates how the CFD toolbox OpenFOAM can be used to simulate such flows. Experimental measurements and observations have been performed on a pilot-scale reactor where pressurized air is injected in a yield stress fluid. The volume of fluid method and an adaptive mesh with refinement at the interface have been used to track the gas inclusions. The numerical model accuracy has been assessed by comparing experimental and numerical results related to the bubble's frequency, dimensions, and rising velocities as well as the fluid recirculation, yielded, and unyielded regions in the tank. The influence of injection parameters such as the injection flow rate and the fluid rheological parameters has been quantified.