A 6-DOF humanoid wall-climbing robot with flexible adsorption feet based on negative pressure suction

A wide range of dangerous and special tasks have witnessed the applications of wall-climbing robots, but they still cannot adapt well torough or sloping walls. This paper proposes a 6-DOF (degree of freedom) humanoid wall-climbing robot (HWCR) based on the principle of negative pressure suction. HWCR has the advantages of flexible adsorption feet, strong adaptability, strong anti-subversion performance, and high friction to the wall. We deduce mechanics formulas and carry out a parametric design of the foot structure so that it can meet the requirement of robot wall climbing. We use Fluent to analyze the flow field of the adsorption foot and determine the motor speed that can provide a reliable adsorption force. Using the D-H matrix to plan gait, we also design a compound cycloid-based foot trajectory to reduce the impact between the HWCR and the wall. Experiments on the uneven wall and sloping wall show that the vehicle can walk with an ideal gait, and the resistance value of the servo on each joint is much lower than the critical value, which ensures the smooth movement of the HWCR.     

Shared human–robot path following control of an unmanned ground vehicle

This paper considers the shared path following control of an unmanned ground vehicle by a single person. A passive measure of human intent is used to blend the human and machine inputs in a mixed initiative approach. The blending law is combined with saturated super-twisting sliding mode speed and heading controllers, so that exogenous disturbances can be counteracted via equivalent control. It is proven that when the proposed blending law is used, the combined control signals from both the human and automatic controller respect the actuator magnitude constraints of the machine. To demonstrate the approach, shared control experiments are performed using an unmanned ground vehicle, which follows a lawn mower pattern shaped path.     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。     

新型树启发式搜索算法的机器人路径规划

面对三维空间移动机器人从起始点到终止点的最短路径问题,提出一种新型的边缘点树启发式搜索(TreeEP)算法,该方法将地图空间进行密度可调的三维离散化处理,根据障碍安全距离筛选出障碍物的可靠边缘点信息,再利用树扩散架构选出最能引导搜索方向的潜力点进行扩散搜索,最终得出最短路径。提出局部调整策略,得到改进的Tree-EP算法。实验结果表明,在带障碍复杂地形最短路径搜索应用中,提出的Tree-EP算法与已有方法相比,能找到更短的移动路径。     

基于并行多通道卷积长短时记忆网络的轴承寿命预测方法

在预测轴承剩余使用寿命时，数据间的时序特性是一个可以利用的重要隐藏信息。为了更好地提取具有时序信息的特征用于预测，提出了一种基于并行多通道卷积长短时记忆网络（PMCCNN-LSTM）的剩余使用寿命预测模型。该模型主要由两部分组成：前端为并行多通道卷积网络（PMCCNN），提取信号特征，挖掘数据的时序特性，并采用逐层训练和微调的方式提升参数的收敛性；后端为长短时记忆（LSTM）网络，基于特征进行剩余使用寿命预测，并采用加权平均的方法对预测结果进行平滑处理。在一个轴承加速寿命实验的公开数据集上使用留一法验证了该模型的准确性，实验结果表明：所提模型的平均误差与最大误差分别比传统的卷积神经网络（CNN）低23.38%和15.84%，比传统的LSTM低24.14%和19.01%，比卷积长短时记忆网络（CNN-LSTM）低30.32%和23.09%。     

基于机器视觉的机车齿轮毂全自动双轴拧紧机的设计和应用

设计了基于机器视觉的机车齿轮毂全自动双轴拧紧机,根据拧紧工艺和扭矩控制原理实现对螺栓拧紧力矩的控制;通过丝杠变径机构,实现不同规格齿轮毂螺栓拧紧;利用机器视觉实现螺栓位置的识别以及初始位置的确定;讨论了自动拧紧机控制系统的硬件组成和软件系统配置,并介绍了防错、防漏功能的设计流程。螺栓自动拧紧机可提高装配精度和操作效率,降低工人的劳动强度。     

Parallel Multipopulation Differential Evolutionary Particle Swarm Optimization for Voltage and Reactive Power Control

This paper presents parallel multipopulation differential evolutionary particle swarm optimization (DEEPSO) for voltage and reactive power control (VQC). The problem can be formulated as a mixed integer nonlinear optimization problem and various evolutionary computation techniques have been applied to the problem including PSO, differential evolution (DE), and DEEPSO. Since VQC is one of the online controls, speed‐up of computation is required. Moreover, there is still room for improvement in solution quality. This paper applies parallel multipopulation DEEPSO in order to speed up the calculation and improve solution quality. The proposed method is applied to IEEE 30, 57, and 118 bus systems. The results indicate that the proposed method can realize fast computation and minimize more active power losses than the conventional evolutionary computation techniques.     

Plant inspection by using a ground vehicle and an aerial robot: lessons learned from plant disaster prevention challenge in world robot summit 2018

Abstract

In recent years, to prevent accidents and disaster are desired by implementing maintenance and management of facilities, such as conducting periodic inspections with appropriate frequency at plants. However, because the dangerous materials such as flammable gas and explosives is used in a plant, and there are many dangerous places in a plant such as high-temperature environment and high places and narrow spaces, it is desirable to use a remote-controlled robot for safety work and short inspections. Against this background, the Disaster Robotics Category-Plant Disaster Prevention Challenge was held in Japan at the World Robot Summit 2018. Our team was ranked 3rd in this competition, because our strategy of ‘inspection and investigation in cooperation with UGV and UAV’ was effective. In this paper, the competition contents of World Robot Summit 2018 and the robot inspection system that we are studying are explained. And what kind of strategy was challenged and result for these given competition tasks by using our robot system are introduced. And the lessons learned such as advantages and issues in UGV and UAV collaboration work at this competition are described for evaluate a robot investigation system for disaster response and inspection work at plants.     

鑫达黄金矿业急倾斜薄矿体中深孔采矿方法的研究与优化

近年来，随着开采技术的发展，急倾斜薄矿脉采用中深孔采矿越来越多。为了降低生产成本，提高经济效益和安全系数。通过在矿房对扇形中深孔和平行中深孔进行现场试验，得到扇形中深孔比平行中深孔工程量少、千吨采切比小的结论。将扇形中深孔采矿方法在急倾斜薄矿脉中进行推广应用，取得了一定经济效益。     

A finite line source simulation model for geothermal systems with series- and parallel-connected boreholes and independent fluid loops

A model for the simulation of geothermal systems with parallel- and series-connected boreholes is presented. Mass and heat balance problems are formulated for each component in the system and are assembled into system-level problems. A third problem is formulated to account for heat transfer in the bore field, using the finite line source solution. This third problem is coupled to the system-level heat balance problem by an analytical solution of the heat transfer inside boreholes with multiple U-tubes. The simulation model allows for any number of independent fluid loops within the bore field or within individual boreholes and allows for combinations of specified inlet fluid temperatures and heat extraction rates in independent fluid loops. The model accounts for the axial variation of the fluid and borehole wall temperatures and heat extraction rates. The capabilities of the model are demonstrated through three example simulations.