Preparation of a Near-Infrared Ray Absorption Film from N-Phenylthiocarbamoyl Chitosan Derivative

We recently observed that the decanoylation of N-phenylthiocarbamoyl chitosan (2) with a mixture of decanoic anhydride and pyridine at 60 °C for 24 h afforded N,N-(decanoyl)phenythiocarbamoyl-/2-isothiocynato chitosan decanoate (3b) rather than the expected product N,N-(decanoyl)phenylthiocarbamoyl chitosan decanoate (3a). This result suggested that some of the N,N-(decanoyl)phenylthiocarmbamoyl groups had been converted to isothiocyanate groups during the decanoylation process. The subsequent reaction of compound 3b with aniline gave N,N-(decanoyl)phenylthiocarbamoyl/N-phenylthiocarbamoyl chitosan decanoate (4) in high yield. A solution of compound 4 in CHCl₃ was then added to a solution of copper decanoate (5) in the same solvent, and the resulting mixture was cast onto a glass plate to give a cast film. The film was annealed at 200 °C in an oven to give a greenish film, which showed good near-infrared absorption characteristic in the range of 800–2200 nm.     

Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Analysis and optimization of high-power pulse transformer for SXFEL

Longitudinal injection is a promising on-axis injection scheme for diffraction-limited storage rings. In the latest version of the Hefei advanced light source(HALS), both the dynamic aperture and momentum aperture have been optimized. A longitudinal injection scheme was investigated on the HALS using a doublefrequency radio frequency system. To evaluate the injection performance, various errors were considered. A series of tracking simulations were conducted, and the injection efficiency was obtained under different error levels.     

Dynamic Stabilization of DNA Assembly by Using Pyrrole-Imidazole Polyamide

We used N-methylpyrrole (Py)-N-methylimidazole-(Im) polyamide as an exogenous agent to modulate the formation of DNA assemblies at specific double-stranded sequences. The concept was demonstrated on the hybridization chain reaction that forms linear DNA. Through a series of melting curve analyses, we demonstrated that the binding of Py−Im polyamide positively influenced both the HCR initiation and elongation steps. In particular, Py−Im polyamide was found to drastically stabilize the DNA duplex such that its thermal stability approached that of an equivalent hairpin structure. Also, the polyamide served as an anchor between hairpin pairs in the HCR assembly, thus improving the originally weak interstrand stability. We hope that these proof-of-concept results can inspire future use of Py−Im polyamide as a molecular tool to modulate the formation of DNA assemblies.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

Gap modulation in MCu[Q1−xQ′x]F (M=Ba, Sr; Q, Q′=S, Se, Te) and related materials

BaCuQF (Q=S, Se, Te) materials exhibit band gaps that allow transmission of much of the visible spectrum. BaCuSF is transparent in thin-film form with a band gap of 3.1 eV. Band gap estimates for powders of the solid solution series BaCuS_1−xSe_xF were obtained from wavelength-dependent diffuse-reflectance measurements using an integrating sphere. The band gap can be tuned by the substitution of Se for S to 2.9 eV for BaCuSeF. The decrease scales almost linearly with the increase in the volume of the tetragonal unit cell, which is determined primarily by the expansion of the a lattice parameter; the overall volume increase is 7.0% from x=0 to 1. Further reduction of the band gap is observed in BaCuSe_1−xTe_xF solid solutions, where a unit cell volume increase of 5.5% produces a band gap of 2.7 eV in BaCuSe_0.5Te_0.5F. Powders and films of BaCuSF exhibit strong red luminescence under ultraviolet excitation, which is suppressed by K doping. Additional tuning of band gap and electrical properties (the materials are p-type conductors) can be achieved by replacing Ba with Sr.     

Microstructure and mechanical behaviour of 3Y-TZP/Mo nanocomposites possessing a novel interpenetrated intragranular microstructure

Yttria stabilized tetragonal zirconia polycrystal (Y-TZP)/0-100 vol % molybdenum (Mo) composites were fabricated by hot-pressing a mixture of Y-TZP powder containing 3 mol % yttria (Y₂O₃) and a fine Mo powder in vacuum. This composite system possessed a novel microstructural feature composed of an interpenetrated intragranular nanostructure, in which either nanometer sized Mo particles or equivalent sized zirconia (ZrO₂) particles located within the ZrO₂ grains or Mo grains, respectively. The strength and toughness were both greatly enhanced with increasing Mo content for the 3Y-TZP/Mo composites thus breaking through the strength-toughness tradeoff relation in transformation toughened ZrO₂ and its composite materials. They exhibited a maximum strength of 2100 MPa and a toughness of 11.4 MPa·m^1/2 for the composite containing 70 vol % Mo. These simultaneous improvements in strength and toughness were determined to be the result of a decrease in flaw size associated with the interpenetrated intragranular nanostructure, and a stress shielding effect created in the crack tip by the elongated Mo polycrystals bridging the crack tip in addition to the stress induced phase transformation.