Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Design for Consecutive Testability of System-on-a-Chip with Built-In Self Testable Cores

This paper introduces a new concept of testability called consecutive testability and proposes a design-for-testability method for making a given SoC consecutively testable based on integer linear programming problem. For a consecutively testable SoC, testing can be performed as follows. Test patterns of a core are propagated to the core inputs from test pattern sources (implemented either off-chip or on-chip) consecutively at the speed of system clock. Similarly the test responses are propagated to test response sinks (implemented either off-chip or on-chip) from the core outputs consecutively at the speed of system clock. The propagation of test patterns and responses is achieved by using interconnects and consecutive transparency properties of surrounding cores. All interconnects can be tested in a similar fashion. Therefore, it is possible to test not only logic faults but also timing faults that require consecutive application of test patterns at the speed of system clock since the consecutively testable SoC can achieve consecutive application of any test sequence at the speed of system clock.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

An accurate experimental method for characterizing transmission lines embedded in multilayer printed circuit boards

We have developed an accurate method for measuring the complex propagation constant and characteristic impedance of transmission lines embedded in multilayer printed circuit boards. It is based on mathematical error-removal schemes using two different length transmission lines and an advanced via-hole structure that minimizes coupling. Consequently, associated errors, due to discontinuities and interference can be effectively eliminated, and the frequency dependencies of the transmission line parameters can be clarified in wide frequency bandwidths. We verified the validity of this method in frequency ranges up to at least 18 GHz, by comparing the determined values with the theory derived from transverse electromagnetic (TEM) approximations.     

Crack opening displacement of a through-wall crack in a plate subjected to bending load

This study was performed in order to clarify crack opening displacement (COD) of through-wall cracks in a plate subjected to bending load. The former COD evaluation methods were mainly developed corresponding to tensile load, but there has been nothing that has been developed corresponding to bending load. Therefore, the authors evaluated CODs of the through-wall cracks in plates which were subjected to a bending load using finite element method (FEM) analyses, and proposed a simplified COD evaluation method accounting for both tensile and bending loads. The proposed method is useful for leakage evaluation at a crack opening of an elbow crown or in the vicinity of the coolant surface of a vessel in which the bending stress is relatively large.     

Survey of switching techniques in high-speed networks and their performance

One of the most promising approaches for high speed networks for integrated service applications is fast packet switching, or ATM (asynchronous transfer mode). ATM can be characterized by very high speed transmission links and simple, hard-wired protocols within a network. To match the transmission speed of the network links, and to minimize the overhead due to the processing of network protocols, the switching of cells is done in hardware switching fabrics in ATM networks. A number of designs have been proposed for implementing ATM switches. Although many differences exist among the proposals, the vast majority of them are based on self-routeing multistage interconnection networks. This is because of the desirable features of multi-stage interconnection networks such as self-routeing capability and suitability for VLSI implementation. Existing ATM switch architectures can be classified into two major classes: blocking switches, where blockings of cells may occur within a switch when more than one cell contends for the same internal link, and non-blocking switches, where no internal blocking occurs. A large number of techniques have also been proposed to improve the performance of blocking and non-blocking switches. In this paper, we present an extensive survey of the existing proposals for ATM switch architectures, focusing on their performance issues.     

Clinical features of primary and secondary atypical mycobacteriosis

A clinical investigation was carried out in 39 patients with atypical mycobacteriosis (AM). The patients at our hospital diagnosed as having AM during an 11-year period from 1981 to 1991 were reviewed in this study. The incidence of AM among all of mycobacterial infections has been increasing since 1988. The atypical mycobacteria detected included M. avium complex (MAC) in 79%, M. kansasii in 26%, and other organisms in 5%. Patients who had primary infection without underlying respiratory disease were compared with those who had secondary infection. In secondary infection, MAC was detected in the sputum of a high percentage of patients and was positive for more than 6 months despite therapy. Gamma globulin levels were also increased in patients with secondary infection. Cell mediated immunity was examined by the DNCB reaction and the detection of CD4- and CD8- positive T lymphocytes. The DNCB skin reaction was positive in 6 out of 26 patients with secondary infection. The percentage of CD8- positive T lymphocytes was higher in patients with secondary disease. Fischer's ratio (indicating the balance of plasma amino acids) was also examined as an index of the nutritional status. It was significantly lower in secondary infection compared with primary infection. Moreover, secondary infection was associated with a lower positive rate for the DNCB skin reaction and a lower Fischer's ratio when compared with pulmonary tuberculosis. Thus impairment of cell-mediated immunity, malnutrition, and a poor prognosis were significantly more common in secondary infection compared with primary infection.     

A novel on-chip electrostatic discharge (ESD) protection withcommon discharge line for high-speed CMOS LSIs

A novel on-chip electrostatic discharge (ESD) protection for high-speed CMOS LSI's that operate at higher than 500 MHz has been developed. Introduction of a newly developed common discharge line (CDL) can completely eliminate the protection device influence on the inner circuit operation. This enables minimization of the I/O capacitance by shrinking the dimension of the output transistor, which also serves as a protection device in conventional devices. This new protection (CDL protection) was applied to a high-speed DRAM of which I/O pin capacitance specification is 2 pF. As a result, the ESD tolerance of 4 kV for the charged device model test, 4 kV for the human body model test, and 700 V for the machine model test were obtained. In addition, the DRAM data rate higher than 660 MHz at room temperature was achieved. The results show significant improvement for both ESD and the I/O capacitance, compared with the conventional structure     

Extended AB Period Study of the Electron Pairing Transition int-J Ladders

The extended Aharonov-Bohm period test, recently proposed by the present authors, is used to study the electron pairing transition in the t-J ladders. The critical point is detected as a gap opening in the extended spectral flow. The result suggests a pairing prior to the onset of a phase separation, which is consistent with a recent Tomonaga-Luttinger analysis.     

The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.