Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

Polarity Effect and Electromagnetic Radiation of Partial Discharge Accompanying Growth of Electrical Tree

We have investigated the characteristics of radiated electromagnetic (EM) waves from positive and negative partial discharges (PD) in epoxy resin and cross‐linked polyethylene. We found that there is a correlation among the EM level from PD, the positive PD current, and electrical trees. Therefore, the growth of an electrical tree produces a lot of positive PD. We have also investigated the characteristics of the frequency region of EM waves from PD in air, insulating oil, and liquid epoxy in addition to the above insulators. EM waves were detected in the frequency region of 40 MHz to 300 MHz from positive and negative PD in epoxy resin and cross‐linked polyethylene. EM waves were also detected in the frequency region of 40 MHz to 150 MHz from positive and negative PD in air. In the case of insulating oil and liquid epoxy, EM waves were detected in the frequency regions of 40 MHz to 150 MHz from positive PD, and 40 MHz to 250 MHz from negative PD. The frequency region differed depending on the material and the discharge polarity. Our investigation indicates that the cause is differences in electric field strength at the time of PD occurrence.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

Recovery of fluorocarbons in Japan as a measure for abating global warming

The objective of this study is to evaluate the potential for recovering fluorocarbons as measures for the abatement of global warming. In this study, we focused on the three different kinds of fluorocarbons: CFCs, HCFCs and HFCs, and targeted refrigerant use because of the availability of relevant data. We first estimated future fluorocarbon emissions from the targeted appliances; we next compared those emissions in the units of CO₂ equivalent to the level of CO₂ emissions in 1990 from a quantitative point of view. As the result of this study, it was found that fluorocarbon emissions in 1999 and 2010 would be equal to approximately 7 and 3% of the level of CO₂ emissions in 1990 respectively. Moreover, if we implement a 100% recovery rate in every recovery route, we can reduce a large amount of emissions which correspond to approximately 2–5% of the level of CO₂ emissions in 1990, even if we take into account the energy-related CO₂ emissions by the transportation and decomposition of fluorocarbons.     

Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Temporal Specificity of Extinction in Autoshaping.

Three experiments investigated the effects of varying the conditioned stimulus (CS) duration between training and extinction. Ring doves (Streptopelia risoria) were autoshaped on a fixed CS-unconditioned stimulus (US) interval and extinguished with CS presentations that were longer, shorter, or the same as the training duration. During a subsequent test session, the training CS duration was reintroduced. Results suggest that the cessation of responding during an extinction session is controlled by generalization of excitation between the training and extinction CSs and by the number of nonreinforced CS presentations. Transfer of extinction to the training CS is controlled by the similarity between the extinction and training CSs. Extinction learning is temporally specific. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Performance prediction of a hybrid‐excitation synchronous machine with axially arranged excitation poles and permanent‐magnet poles

This paper presents a method of predicting the steady‐state performance of a new hybrid‐excitation synchronous machine (HESM) theoretically. The field pole of this HESM is axially divided into two parts; one is an excitation part and the other a permanent‐magnet (PM) part. A nonlinear equivalent circuit, which can include the saliency of the rotor and the magnetic saturation due to the iron core, is derived. Based on this equivalent circuit, the steady‐state performance of the HESM is calculated, and the results are confirmed through experiments. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 43–49, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20033