Lab-scale feasibility study on new elastomer comprising chloroprene and acrylonitrile for oil and gas applications

The limited options of suitable elastomers with adequate cost-performance balance drive the necessity to introduce new materials in the oil & gas (O&G) application space. The relevance of a recently developed copolymer of chloroprene and acrylonitrile (referred to as acrylonitrile–chloroprene rubber or NCR) to O&G applications is described in this technical contribution. The new elastomer demonstrates adequate physical properties and reasonably good high and low-temperature capabilities. It offers good resistance to several aqueous and non-aqueous fluids with low volume swelling and retains its physical properties to reasonable extents while exposed to hot test oils. Acrylonitrile–chloroprene rubber has been found to sustain “sour gas” exposure. Good abrasion resistance, high tear strength, and remarkably high flex-fatigue resistance coupled with low heat build-up reflect its durability under dynamic conditions. In addition, acrylonitrile–chloroprene rubber can very well withstand the rapid gas decompression test at 25°C. This unique combination of attributes may allow acrylonitrile–chloroprene rubber to be considered as a candidate material for high-performance O&G applications.     

Physico-chemical properties of glycyrrhizic acid in aqueous media. I. Surface-active properties and formation of molecular aggregates (author''s transl)

As shown in 138 embryos and fetuses in the 40-285 mm crown-rump length range, carpal and carpal-metacarpal "fusions" arise from incomplete separation of the cartilaginous precursors rather than from failure of initiation, thus accounting for the "fusions" seen in postnatal radiographs and the grooves that are evident enough in adult fusions. Radiographs selected from over 20,000 apparently normal individuals provide postnatal counterparts for the prenatal examples shown in histological sections.     

High-Performance Induction Motor Drive System Using a PWM Inverter

A high-performance speed control system for cage induction motors is described which utilizes a PWM inverter. The effects of primary current coincidence and machine constant variation on system characteristics such as response time, torque precision, and operating noise were investigated. Based on the results obtained, new control methods have been devised; one varies the gain of the current controller in proportion to the primary frequency, and a second compensates for the slip frequency by using the deviation between the flux reference value and the actual value. Effectiveness of the compensation methods was confirmed in tests.     

In vivo performance of wax matrix granules prepared by a twin-screw compounding extruder

The in vivo performance of wax matrix granules (WMGs) prepared by a twin-screw compounding extruder was evaluated in fasted beagle dogs. In vitro dissolution behavior of the model drug, diclofenac sodium (DS), from WMGs was strongly influenced by pH in a dissolution medium due to its solubility (DS is soluble in pH 6.8 and insoluble in pH 1.2 and 4.0) and was independent of paddle rotation rate (50, 100, and 200 rpm) of the dissolution apparatus. Pharmacokinetics parameters such as mean residence time (MRT) showed a sustained action of WMGs in beagle dogs; however, the transit time of WMGs in the small intestine is found to control total drug absorption. Furthermore, the values of the area under the curve (AUC) of the plasma concentration-time curve and the maximum concentration Cmax significantly decreased with decreases in hydroxypropylcellulose (HPC) content in WMGs. Good correlation between one in vitro dissolution parameter (mean dissolution time, MDT) and two in vivo parameters (AUC12 and MRT) suggested that it would be possible to design WMGs with a desired in vivo performance by controlling HPC content.     

Starting method of a superconducting generator in a combined‐cycle power plant

In the combined‐cycle power plant generators are started by using the igniting arrangement up to the ignition rotational speed of the gas turbine. On the other hand, in the case of using the superconducting generator, it is difficult to apply the igniting arrangement used to generate electricity on the combined cycle for the structure as is. We examined the induction motor starting method for the superconducting generator by using the 70‐MW‐class quick‐response excitation superconducting model generator and the VVVF power supply. From the examination, we confirmed the ability to raise the rotational speed from 6 to 360 rpm. Moreover, it was found to be able to start 200‐MW‐class superconducting generators by the induction motor starting method with the analysis. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(2): 30– 38, 2007; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20283     

Epitaxial growth of titanium oxide thin films on MgO(100) single-crystal substrates by reactive deposition methods

We synthesized titanium oxide thin films on MgO(100) single-crystal substrates by two reactive deposition methods and compared the structures of the thin films formed by these methods. In one method (pulsed-molecular-beam deposition method), molecular oxygen is supplied to the substrates by using a pulsed-molecular-oxygen beam source and deposition of one unit layer of titanium and subsequent supply of molecular oxygen are repeatedly performed. In the other method (radical beam deposition method), atomic oxygen is irradiated to the substrates by using an atomic oxygen beam generated by the radical beam source and irradiation of the atomic oxygen and deposition of titanium are simultaneously performed. In the case of the pulsed-molecular-beam deposition method, the crystal structure was changed by increasing the number of oxygen pulses supplied from the beam source. We found that the crystal structure of titanium oxide depended on the composition ratio of O:Ti in the film. The maximum ratio of O:Ti attainable by this method was 1.85, and at this ratio, (100)-oriented pseudorutile was formed. In the case of the radical beam deposition method, (100)-oriented anatase was formed below the titanium deposition rate of 0.10 nm/s and pseudorutile (TiO_2−δ) was formed above 0.15 nm/s. The pseudorutile structure synthesized on this experiment was very stable in air. We concluded that the crystal structure of the pseudorutile is a new crystal structure of titanium oxide.     

A Nifedipine Coground Mixture with Sodium Deoxycholate. II. Dissolution Characteristics and Stability

Nifedipine is a poorly water soluble drug that demonstrates low bioavailability. In a previous study, a coground mixture of nifedipine with sodium deoxycholate (DCNa), a bile salt, immediately produced colloidal particles when dispersed in water. In this study, the effect of the weight fraction of DCNa, grinding time, dissolution media, and storage conditions on colloidal particle formation in solution was investigated. The coground mixture was prepared with a vibration rod mill, and its solid state was characterized using powder X-ray diffraction. A laser diffraction particle size analyzer was used to determine the particle size distribution curve in water. The size of particles formed in solution decreased with an increase in the weight fraction of DCNa and grinding time. A nifedipine-DCNa (1 : 2 w/w) mixture coground for 30 min was used in the experiments. Colloidal particle formation from the coground mixture was also observed in dissolution media of water and a pH 6.8 buffer solution at 37°C. Most precipitates passed through a filter with a pore size of 0.8 μm, but the particle size distribution in water was different from that in the pH 6.8 buffer solution. DCNa exhibited not only micellar solubilization for drug crystals, but also a retarding effect on drug crystal growth in a supersaturated solution. The latter effect could serve to form colloidal particles in solution. When stored under 75% relative humidity at 40°C for 1 month, the amorphous coground mixture crystallized, and the particle size in water markedly increased. Therefore, the weight fraction of DCNa, grinding time, dissolution media, and humidity during storage influence the dissolution characteristics of nifedipine from a coground mixture.     

Purification, characterization, and steady-state kinetics of a meta-cleavage compound hydrolase from Pseudomonas fluorescens IPO1

2-Hydroxy-6-oxo-7-methylocta-2,4-dienoate (6-isopropyl-HODA) hydrolase (CumD), an enzyme of the cumene biodegradation pathway encoded by the cumD gene of Pseudomonas fluorescens IP01, was purified to homogeneity from an overexpressing Escherichia coli strain. SDS-polyacrylamide gel electrophoresis and gel filtration demonstrated that it is a dimeric enzyme with a subunit molecular mass of 32 kDa. The pH optima for activity and stability were 8.0 and 7.0-9.0, respectively. The enzyme exhibited a biphasic Arrhenius plot of catalysis with two characteristic energies of activation with a break point at 20 degrees C. The enzyme has a K(m) of 7.3 microM and a k(cat) of 21 s(-1) for 6-isopropyl-HODA (150 mM phosphate, pH 7.5, 25 degrees C), and its substrate specificity covers larger C6 substituents compared with another monoalkylbenzene hydrolase, TodR Unlike TodF, CumD could slightly hydrolyze 2-hydroxy-6-oxo-6-phenylhexa-2,4-dienoate (6-phenyl-HODA). A mutant enzyme as to a putative active site residue, S103A, had 10(5)-fold lower activity than that of the wild-type enzyme.