A novel ceramic matrix composite based on YNbO4–TiO2 for microwave applications

This work presents the dielectric properties of YNbO₄ (YNO)–TiO₂ composites in the microwave range. X-ray diffraction analysis demonstrates that the addition of TiO₂ to YNO results in the formation of a Y(Nb_0.5Ti_0.5)₂O₆ phase. In the microwave range, the values of permittivity and dielectric loss did not present major changes with the increment of TiO₂. Moreover, the addition of TiO₂ results in an improvement in the thermal stability of YNO, with YNO63 demonstrating a resonant frequency of ?8.96 ppm.°C^?1. We utilised numerical simulations to evaluate the behaviour of these materials as dielectric resonator antennae and it is found that they exhibit a reflection coefficient below ?10 dB at the resonant frequency, with a realised gain of 4.94 – 5.76 dBi, a bandwidth of 665–1050 MHz and a radiation efficiency above 84%. Our results indicate that YNO–TiO₂ composites are interesting candidates for microwave operating devices.     

Chitosan Microspheres as Carriers for pH‐Indicating Species in Corrosion Sensing

Chitosan microspheres containing bromocresol green, cresol red, and phenolphthalein for corrosion detection, through pH change, are synthesized in order to be used in protective coatings for aluminium alloys. Microspheres containing corrosion detection species are characterized morphologically (SEM) and physico‐chemically (FTIR, TGA). Release studies (UV–vis) are performed in corrosion‐promoting conditions (pH, NaCl), and detection studies by immersion in media associated with corrosion activity while microspheres' sensing activity is evaluated visually. Electrochemical characterization of AA2024 substrates in the presence of chitosan spheres is performed to understand material performance, and a color change is observed as a result of local pH increase in cathodic areas when corrosion takes place. These findings can be correlated with the results from release studies and seem a promising approach for corrosion sensing purposes, not only because pH increase is possible to detect due to corrosion, but also because chitosan is considered an environmentally friendly material.     

A New Hand-Held Microsystem Architecture for Biological Analysis

This paper presents a hand-held microsystem based on new fully integrated magnetoresistive biochips for biomolecular recognition (DNA hybridization, antibody antigen interaction, etc.). Magnetoresistive chip surfaces are chemically treated, enabling the immobilization of probe biomolecules such as DNA or antibodies. Fluid handling is also integrated in the biochip. The proposed microsystem not only integrates the biochip, which is an array of 16times16 magnetoresistive sensors, but it also provides all the electronic circuitry for addressing and reading out each transducer. The proposed architecture and circuits were specifically designed for achieving a compact, programmable and portable microsystem. The microsystem also integrates a hand-held analyzer connected through a wireless channel. A prototype of the system was already developed and detection of magnetic nanoparticles was obtained. This indicates that the system may be used for magnetic label based bioassays     

Cost-Efficient SHA Hardware Accelerators

This paper presents a new set of techniques for hardware implementations of Secure Hash Algorithm (SHA) hash functions. These techniques consist mostly in operation rescheduling and hardware reutilization, therefore, significantly decreasing the critical path and required area. Throughputs from 1.3 Gbit/s to 1.8 Gbit/s were obtained for the SHA implementations on a Xilinx VIRTEX II Pro. Compared to commercial cores and previously published research, these figures correspond to an improvement in throughput/slice in the range of 29% to 59% for SHA-1 and 54% to 100% for SHA-2. Experimental results on hybrid hardware/software implementations of the SHA cores, have shown speedups up to 150 times for the proposed cores, compared to pure software implementations.      

咪唑封端扩链脲改性环氧树脂E-51/酸酐MTHPA体系性能研究

以端羟基聚环氧丙烷1000，甲苯二异氰酸酯（TDI），2－甲基咪唑为原料，合成了扩链脲TI，利用DSC，动态热机械分析仪DMA，冲击试验机及扫描电镜（SEM）等手段对TI改性的环氧树脂E－51／甲基四氢化邻苯二甲酸酐（MTHPA）固化体系的反应活性，动态力学行为，冲击性能，断裂面形态结构进行了系统研究，结果表明，改性后的E－51／MTHPA体系反应活性明显提高，固化反应峰顶温度较未改性体系降低160℃－200℃，固化反应的表观活化能由未改性体系的160．3kJ/mol降至63kJ/mol-87kJ/mol，同时与未改性体系相比，经过改性的环氧树脂固化体系冲击强度有较大的提高，在TI含量为5％时体系的玻璃化转变温度Ts达到最高，各改性体系冲击断面呈韧性断裂。     

HIV-1 and HIV-2 antibodies in pregnant women in the City of Maputo, Mozambique. A comparative study between 1982/1983 and 1990

The seroprevalence of HIV-1 and HIV-2 among pregnant women in Maputo, the capital of Mozambique, was compared between the years 1982/83, 1988 and 1990. None of the 432 serum samples collected in 1982/83 was positive for HIV antibodies whereas in 1988 the HIV-1 and HIV-2 seroprevalence was 0.4% (2/500) and 0.6% (3/500), respectively, and in 1990 0.6% (12/2014) and 0.2% (4/2014), respectively. These results indicate that HIV infection has been introduced recently in Maputo and is spreading at a slow rate among women.     

Delay spread measurements for the digital cellular channel inToronto

The paper describes a set of measurements performed in the Toronto area, in order to assess the impact of multipath propagation on the performance of the TIA IS-54 digital standard. Five existing cells were systematically surveyed: two in downtown Toronto, two in the suburbs, and one in a suburban/rural area. A sweeping correlator apparatus with a 0.1 μs resolution and 910 MHz carrier frequency, and an omnidirectional antenna was used. In one of the cells, the measurements were repeated with a 60 degree beamwidth directional antenna. A fairly sophisticated thresholding technique was applied in order to reduce the impact of noise. Generally, the measurements with the omnidirectional antenna exhibit multipath propagation with considerably smaller excess delays than some reported, but are consistent with earlier results obtained in the U.S. and Europe. Sectorization was found to considerably reduce the multipath effects. Very large delay components appear to be due mostly to the combination of large transmitter-receiver distances and a large degree of shadowing, and could probably be avoided to a large extent by standard cellular engineering techniques. In view of these results, it seems that the long delay (high selectivity) problem has been somewhat overemphasized in the past, at least for areas like Toronto. Problems associated with short delays (flat fading), on the contrary, appear to have been underestimated in the case of dense urban environments     

Determining the Tensile Stress-Crack Opening Curve of Concrete by Inverse Analysis

The determination of the fundamental stress versus crack opening (σ-w) response of concrete under uniaxial tension is performed in this study through inverse analysis using data from notched beam tests. The procedure used for optimizing the parameters of the σ-w relation using the load versus crack mouth opening displacement response of the notched beam is described. Satisfactory comparisons have been obtained between the σ-w curves obtained through the inverse analysis and those directly measured in uniaxial tension tests. The use of weighting functions in the inverse analysis may be necessary when large crack widths are to be considered.     

Density of 1,1-dichloro-1-fluoroethane (HCFC 141b) as a function of temperature and pressure

The density of HCFC 141b has been measured at several temperatures between 260 and 320 K, Mid pressures up to 20 MPa, with a mechanical oscillator densimeter. The densimeter was calibrated with 2,2,4-trimethylpentane, whose density was obtained from a correlating cyuation with 0.3% uncertainty. The density data obtained for HCFC 14H) hits a reproducibility of 0.05% and an uncertainty of 0.3%. The data obtained were fitted to a Tait-type equation. which reproduced the experimental densities within 0.11 % and were compared with the data obtained in other works.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.