A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

Metabolic-heat relation for aerobic yeast respiration and fermentation

A specially developed temperature control system on a laboratory scale fermenter enabled continuous measurement of the rate of heat production during undisturbed growth of microbial cultures. Apart from being correlated with oxygen uptake rate, the heat of fermentation was established as an additional indicator of metabolic activity. The ‘aerobic respiration’ energetic activity of Candida utilis, Candida lipolytica and Saccharomyces cerevisiae on different carbon substrates was investigated with cultures of the latter species being also studied under the ‘aerobic fermentation’ conditions induced by glucose catabolite repression.     

A study of solid circulation rate in a circulating fluidized bed

An experimental investigation under cold condition was made to study the effects of some operating/design parameters and non-mechanical L valve configuration on the solid circulation rate in a 4.5 m tall, 0.15 m diameter circulating fluidized bed with riser flow rate varying from 1400 litres/min to 2000 litres/min and bed inventory from 15 kg to 25 kg of sand of average sizes 200 μm, 400 μm and 500 μm. Solid circulation rate was estimated by measuring velocity of sand particle travelling through a vertical Perspex tube section at the bottom of the return leg. It was found to be in the range of 2.8 to 12.3kg/m²s, 0.07 to 9.1kg/m²s and 0.12 to 2.23kg/m²s for sand sizes of 200 μm, 400 μm and 500 μm, respectively for a horizontal L valve. Two mathematical correlations have been developed from the experimental results to predict solid circulation rate as a function of riser flow rate, aeration flow rate, total bed inventory and particle size used.     

A genetic algorithm for the optimisation of assembly sequences

This paper describes a Genetic Algorithm (GA) designed to optimise the Assembly Sequence Planning Problem (ASPP), an extremely diverse, large scale and highly constrained combinatorial problem. The modelling of the ASPP problem, which has to be able to encode any industrial-size product with realistic constraints, and the GA have been designed to accommodate any type of assembly plan and component. A number of specific modelling issues necessary for understanding the manner in which the algorithm works and how it relates to real-life problems, are succinctly presented, as they have to be taken into account/adapted/solved prior to Solving and Optimising (S/O) the problem. The GA has a classical structure but modified genetic operators, to avoid the combinatorial explosion. It works only with feasible assembly sequences and has the ability to search the entire solution space of full-scale, unabridged problems of industrial size. A case study illustrates the application of the proposed GA for a 25-components product.     

Soluble Prokaryotic Overexpression and Purification of Human GM-CSF Using the Protein Disulfide Isomerase b′a′ Domain

Granulocyte-macrophage colony-stimulating factor (GM-CSF) is a member of the colony-stimulating factor (CSF) family, which functions to enhance the proliferation and differentiation of hematopoietic stem cells and other hematopoietic lineages such as neutrophils, dendritic cells, or macrophages. These proteins have thus generated considerable interest in clinical therapy research. A current obstacle to the prokaryotic production of human GM-CSF (hGM-CSF) is its low solubility when overexpressed and subsequent complex refolding processes. In our present study, the solubility of hGM-CSF was examined when combined with three N-terminal fusion tags in five E. coli strains at three different expression temperatures. In the five E. coli strains BL21 (DE3), ClearColi BL21 (DE3), LOBSTR, SHuffle T7 and Origami2 (DE3), the hexahistidine-tagged hGM-CSF showed the best expression but was insoluble in all cases at each examined temperature. Tagging with the maltose-binding protein (MBP) and the b′a′ domain of protein disulfide isomerase (PDIb′a′) greatly improved the soluble overexpression of hGM-CSF at 30 °C and 18 °C. The solubility was not improved using the Origami2 (DE3) and SHuffle T7 strains that have been engineered for disulfide bond formation. Two conventional chromatographic steps were used to purify hGM-CSF from the overexpressed PDIb′a′-hGM-CSF produced in ClearColi BL21 (DE3). In the experiment, 0.65 mg of hGM-CSF was isolated from a 0.5 L flask culture of these E. coli and showed a 98% purity by SDS-PAGE analysis and silver staining. The bioactivity of this purified hGM-CSF was measured at an EC₅₀ of 16.4 ± 2 pM by a CCK8 assay in TF-1 human erythroleukemia cells.     

Motion of points and lines in the uncalibrated case

In the present paper we address the problem of computing structure and motion, given a set point and/or line correspondences, in a monocular image sequence, when the camera is not calibrated.Considering point correspondences first, we analyse how to parameterize the retinal correspondences, in function of the chosen geometry: Euclidean, affine or projective geometry. The simplest of these parameterizations is called the FQs-representation and is a composite projective representation. The main result is that considering N+1 views in such a monocular image sequence, the retinal correspondences are parameterized by 11 N–4 parameters in the general projective case. Moreover, 3 other parameters are required to work in the affine case and 5 additional parameters in the Euclidean case. These 8 parameters are calibration parameters and must be calculated considering at least 8 external informations or constraints. The method being constructive, all these representations are made explicit.Then, considering line correspondences, we show how the the same parameterizations can be used when we analyse the motion of lines, in the uncalibrated case. The case of three views is extensively studied and a geometrical interpretation is proposed, introducing the notion of trifocal geometry which generalizes the well known epipolar geometry. It is also discussed how to introduce line correspondences, in a framework based on point correspondences, using the same equations.Finally, considering the F Qs-representation, one implementation is proposed as a motion module, taking retinal correspondences as input, and providing and estimation of the 11 N–4 retinal motion parameters. As discussed in this paper, this module can also estimate the 3D depth of the points up to an affine and projective transformation, defined by the 8 parameters identified in the first section. Experimental results are provided.     

An integrated system for process planning and cost estimation in hole making

The process planning function plays a critical role not only in computer integrated manufacture, but also in the economics of batch manufacturing. This paper describes the development of a generic knowledge-based system for process planning and cost estimation in the hole making process. The main function of the system, besides estimating the cost of production, is to recommend appropriate processes, their sequence and their respective machining conditions in order to obtain the required product specifications. The system has been implemented in a manufacturing organisation. The results obtained have indicated that in addition to cost savings the system also preserves the consistency in planning and cost estimation.     

Do Agile Managed Information Systems Projects Fail Due to a Lack of Emotional Intelligence?

Information Systems Frontiers - Agile development methodologies (ADM) have become a widely implemented project management approach in Information Systems (IS). Yet, along with its growing...     

Macrotexture influence on vibrational mechanisms of the tyre–road noise of an asphalt rubber pavement

The road surface is one of the most important factors that have influence on the current traffic noise. Usually, for dense surfaces, impacts of the tyre on the pavement generate vibrations which are the dominant mechanisms in the tyre–road noise. In this study, the effect of muffling these vibrations, by the incorporation of crumb rubber (CR) from wasted tyres into asphalt pavements, has been evaluated acoustically. Close proximity measurements have been carried out to register the sound emission generated in the contact zone between a reference tyre and an experimental asphalt pavement with CR. The analysis of the measurements indicates that the incorporation of CR as well as the air voids content has less influence than the macrotexture of the road surface on the acoustical behaviour of this experimental asphalt pavement.