Evolution of properties of parts during MIM and sintering of recycled oxide particles

Metal injection moulding (MIM) is an established process for high volume production of complex shaped metallic parts using commercially available feedstocks. The characteristics of parts after moulding, debinding, and sintering cannot be simply predictable from raw materials because the properties get altered with the process parameters and the corresponding levels of porosity during processing steps. In this study, physical properties, microstructure, and mechanical properties of the MIM parts have been characterised to understand the evolution of strength during various steps in MIM processing. Feedstocks with different binder loading show a considerable difference in physical as well as mechanical characteristics. During sintering of parts which have solid loading of grinding sludge, simultaneous in situ reduction and densification takes place, whereas only densification occurs in carbonyl iron parts. It is, therefore, possible to make complex shaped parts of different levels of porosity from downgraded shop floor metallic waste.     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Synthesis, Characterization and Crystal Structure of Quaternary Complex of Gadolinium （Ⅲ）

Ａｎｕｍｂｅｒｏｆｌａｎｔｈａｎｉｄｅｔｅｒｎａｒｙｃｏｍｐｌｅｘｅｓｃｏｎ ｔａｉｎｉｎｇｈｅｔｅｒｏｃｙｃｌｉｃａｍｉｎｅｓｈａｖｅｂｅｅｎｒｅｐｏｒｔｅｄｓｉｎｃｅ1960 [1] .Ｉｎｒｅｃｅｎｔｙｅａｒｓｍｕｃｈａｔｔｅｎｔｉｏｎｈａｓｂｅｅｎｐａｉｄｔｏｑｕａｔｅｒｎａｒｙｃｏｍｐｌｅｘｅｓｏｆｌａｎｔｈａｎｉｄｅｓｂｅｃａｕｓｅｏｆｉｎ ｔｅｒｅｓｔｉｎｇｓｔｒｕｃｔｕｒｅ ,ｃｏｏｒｄｉｎａｔｉｏｎｍｏｄｅ ,ｃｏｍｐｅｔｉｔｉｏｎｒｅ ａｃｔｉｏｎａｎｄｐｒｏｐｅｒｔｙ[2～ 9] .ＥＳＲｃａｎｅ…     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

A novel dynamic survivable routing in WDM optical networks with/without sparse wavelength conversion

In this paper, we study the dynamic survivable routing problem, both in optical networks without wavelength conversion and in optical networks with sparse wavelength conversion, and propose a novel hybrid algorithm for it based on the combination of mobile agents technique and genetic algorithms (GA). By keeping a suitable number of mobile agents in the network to cooperatively explore the network states and continuously report cycles (that are formed by two disjoint-link routes) into the routing tables, our new hybrid algorithm can promptly determine the first population of cycles for a new request based on the routing table of its source node, without the time consuming process associated with current GA-based lightpath protection schemes. We further improve the performance of our algorithm by introducing a more advanced fitness function that is suitable for both the above networks. Extensive simulation studies on the ns-2 network simulator show that our hybrid algorithm achieves a significantly lower blocking probability than the conventional survivable routing algorithms for all the cases we studied.     

Preferential Oxidation of CO in H2-Rich Gas at Low Temperatures over Au Nanoparticles Supported on Metal Oxides

We investigated Au catalysts supported on TiO₂, Fe₂O₃, and ZnO for their preferential oxidation of CO in a H₂-rich atmosphere. Both full conversion and selectivity were achieved over Au/Fe₂O₃ and Au/ZnO around room temperature, but at higher temperatures the CO conversion was suppressed due to competition between CO and H₂.     

Interaction of two close quantized vortices in superfluid4He

The three-dimensional dynamics of two interacting quantized vortex filaments is studied. The equations of motion and the method of numerical calculation follow Schwarz. Whether two approaching filaments reconnect or not depends on their arrangement before approach. When a ring moves toward a line from a distance, only within a critical initial distance they can reconnect. The critical distance is minimized when their circulations are parallel at the closest place, while it increases as their circulations begin to deviate from being parallel. Hence the reconnection probability can be less than unity.     

Applications of the 4×4 determinant method and the POLYGON ENGINE

In the first half of the paper, various types of processing pertaining to a polygon, using the 4×4 determinant theories are explained along with a new containment test algorithm of a point in a polygon. In the latter half of the paper, a general-purpose geometric processor, the POLYGON ENGINE, is presented which can deal with various types of interference problems, such as Boolean operations in solid modelling, hidden line and surface eliminations, ray tracing and so on. It is, a successor of the TRIANGLE PROCESSOR and is also based upon the 4×4 determinant theories [4–6]. While the TRIANGLE PROCESSOR processes a triangulated polygon on a triangle-by-triangle basis, the POLYGON ENGINE can treat a polygon without triangulation. The latter is expected to be more functional, more efficient and easier to use.