Photoinduced Formation of Small Gold Particles in Silica Gels

AuCl⁻₄ ions in sol-gel-derived silica gels (Au/silica gels) were photoreduced by ultraviolet light irradiation at room temperature. In the presence of ethylene glycol in the silica gels, small Au particles were effectively formed by the irradiation. When the storage temperature of the gels was increased in the dark after the irradiation, the surface plas-mon resonance absorption peak of the Au particles was shifted to longer wavelengths, indicating that the Au particles became large. At a storage temperature below 9°C, Au particles could not be observed in the silica gels. The apparent activation energy of Au particle formation was estimated to be 17. 3 kcal·tmol⁻¹.     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Mechanical properties of SiNxCx ceramic films prepared by plasma CVD

The mechanical properties of Si₃N₄-SiC, SiN_x and SiC_y films prepared at a low temperature of 400 °C by plasma chemical vapour deposition are reported. Microhardness, internal stress of the film and adhesive strength between the film and glass or stainless steel substrate were evaluated as principal mechanical properties. Microhardness was measured to be about 10 to 20 G Pa dependent on the film composition in each system. Internal stress of the films on borosilicate glass substrates extensively varied from tensile to compressive with the film composition change from Si₃N₄ to SiC. Adhesive strength, as ascertained by the scratch test, was about 580 to 800 MPa for crown glass substrates, and about 210 to 310 M Pa for 316 stainless steel substrates. It is pointed out that tensile stress in these films brought about more abrupt decreases of the adhesive strength than did compressive stress.     

[110]-surface strained-SOI CMOS devices

We have newly developed [110]-surface strained-silicon-on-insulator (SOI) n- and p-MOSFETs on [110]-surface relaxed-SiGe-on-insulator substrates with the Ge content of 25%, fabricated by applying the Ge condensation technique to SiGe layers grown on [110]-surface SOI wafers. We have demonstrated that the electron and the hole mobility enhancement of [110]-surface strained-SOI devices amounts to 23% and 50%, respectively, against the mobilities of [110]-surface unstrained MOSFETs. As a result, the electron and the hole mobility ratios of [110]-surface strained-SOI MOSFETs to the universal mobility of (100)-surface bulk-MOSFETs increase up to 81% and 203%, respectively. Therefore, the current drive imbalance between n- and p-MOS can be reduced. Moreover, both the electron and the hole mobilities of the [110]-surface strained-SOIs strongly depend on the drain current flow direction, which is qualitatively explained by the anisotropic effective mass characteristics of the carriers on a [110]-surface Si. As a result, the [110]-surface strained-SOI technology with optimization of the current flow directions of n- and p-MOS is promising for realizing higher speed scaled CMOS.     

Phase diagrams calculated for Fe-rich Fe-Si-Co and Fe-Si-Al ordering alloy systems

Theoretical analysis based on the calculation of phase diagrams was employed for Fe-Si-Co and Fe-Si-Al ordering systems to clarify the necessity for the occurrence of phase separation in Fe-base ternary ordering systems. The free energy of Fe-base ternary ordering alloys where B2 and D0₃ ordered structures are formed is evaluated statistically using a pairwise interaction approximation up to second nearest neighbours, taking into account not only the atomic interaction but also the magnetic interaction, based on the Bragg-Williams-Gorsky model. The calculated phase diagrams are consistent with the experimentally obtained ones. The phase diagram calculation in this work is useful to predict the equilibrium states of the ternary ordering systems. The phase separation in ordering alloys is caused by the contribution of excess free energies due to ordering. The influences of ferromagnetism on the two-phase regions are also demonstrated.     

Hepatitis GB virus C genome in the serum of aplastic anaemia patients receiving frequent blood transfusions

GB virus C (GBV-C) RNA was detected in five of 18 patients with aplastic anaemia who had received blood transfusions, whereas it was not detected in eight patients who had not received any transfusions. Antibody against hepatitis C virus (anti-HCV) was detected in nine patients in the transfusion group, compared with one of eight who had not received any transfusions. Therefore, the route of transmission of both GBV-C and HCV in these patients appeared to have been multiple blood transfusion. Since all of the GBV-C RNA-positive patients harboured anti-HCV, GBV-C seems to frequently superinfect with HCV. Neither GBV-C nor HCV is likely to have been a causative agent of the anaemia in the cases examined.     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.