基于系统性能的近地告警技术研究

基于多种导航信息综合处理、告警计算的近地告警系统，对于避免可控撞地事故、 提升飞机安全具有重要意义。本文首先介绍了近地告警系统的工作原理，研究了基于 SOC 曲线的告警包线设计技术，并以过大近地速率告警模式为例进行了告警包线的仿真。最后，利用实际飞行数据分析验证了告警包线合理性以及导航信息可靠性对系统性能的影响。     

安卓平台上的医用图像信息采集系统的开发设计

为了探讨在安卓平台上构建医用图像采集系统的开发个案,分析通过以智能手机、平板电脑为核心安卓设备通过拍照获得化验单数据后进行文本识别并提交智慧医疗系统的解决方案。本文首先通过二值化算法形成低阈值图像数据,使用卷积神经元网络算法对文本进行逐一识别,使用K-means算法对识别后的单字文本进行字段记录值的整合并形成元数据库服务于其他智慧医疗系统模块。在使用9000组数据对神经元网络进行前期训练的前提下,该系统的识别准确率达到了99.5%以上。本系统具有一定的可行性,对未来智慧医疗的系统开发有实践意义。     

响应面法优化艾叶挥发油的提取工艺及其抗氧化性能研究

以艾叶挥发油提取率为考核指标,采用单因素实验考察浸泡时间、料液比、提取时间等对艾叶挥发油提取率的影响,在此基础上,采用响应面法优化艾叶挥发油的共水蒸馏提取工艺,并通过紫外分光光度法测定艾叶挥发油对DPPH自由基的清除率来评价其抗氧化性能。结果表明,艾叶挥发油的最佳提取工艺条件为:浸泡时间1.5 h、料液比1∶10(g∶mL)、提取时间4.5 h,在此条件下,艾叶挥发油提取率最高,为0.83%。当艾叶挥发油浓度为80 mg·mL~(-1)时,DPPH自由基清除率最高,为39.12%。表明艾叶挥发油具有一定的抗氧化活性。     

Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

铸态Ti-20Zr-20Al钛合金动态压缩力学性能与断裂机制研究

采用X射线衍射仪、金相显微镜、分离式霍普金森杆和扫描电镜等手段研究了Ti-20Zr-20Al钛合金在动态压缩条件下的微观结构、力学性能和断裂机制。结果表明,Ti-20Zr-20Al铸态合金由Zr基体相和TiAl/Ti₃Al针状相组成; 随着应变率增加,合金的抗压强度增加,失效应变显著增加; Ti-20Zr-20Al合金的断裂机制为解理断裂; 随着应变率增加,试验压缩断裂后碎片总数增大,平均粒径减小。采用DID模型模拟的材料碎片尺度与实验结果比较吻合,Grady模型与实验结果的偏差较大。     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。     

Hydrogel photocatalysts for efficient energy conversion and environmental treatment

Photocatalysts have attracted great research interest owing to their excellent properties and potential for simultaneously addressing challenges related to energy needs and environmental pollution. Photocatalytic particles need to be in contact with their respective media to exhibit efficient photocatalytic performances. However, it is difficult to separate nanometer-sized photocatalytic materials from reaction media later, which may lead to secondary pollution and a poor recycling performance. Hydrogel photocatalysts with a three-dimensional (3D) network structures are promising support materials for photocatalysts based on features such as high specific surface areas and adsorption capacities and good environmental compatibility. In this review, hydrogel photocatalysts are classified into two different categories depending on their elemental composition and recent progresses in the methods for preparing hydrogel photocatalysts are summarized. Moreover, current applications of hydrogel photocatalysts in energy conversion and environmental remediation are reviewed. Furthermore, a comprehensive outlook and highlight future challenges in the development of hydrogel photocatalysts are presented.