吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

三维石墨烯-碳纳米管/水泥净浆的压敏性能

为了探索三维石墨烯-碳纳米管(G-CNTs)/水泥净浆的压敏性能,采用四电极法研究了荷载作用下GCNTs/水泥净浆的电阻率变化,并分析不同G-CNTs掺量、加载幅度、加载速度以及恒定荷载对电阻率变化的影响。研究表明:随着G-CNTs掺量的增加,电阻率呈先减小后稳定的变化趋势,在G-CNTs掺量由0.2wt%增加至1.6wt%时,电阻率下降51.8%;电阻率与温度呈负相关;G-CNTs掺量高于0.8wt%时可以显著提高水泥净浆的压敏性能,且电阻率变化率与应力应变有明显的对应关系,1.2wt%G-CNTs掺量下试件的应力灵敏系数和应变灵敏系数分别为2.3%/MPa和291;G-CNTs/水泥净浆电阻率变化率幅值随着加载幅度增大而相应增加,其电阻率变化率曲线在不同加载速度以及恒定荷载作用下均与应力-应变曲线一一对应,具有良好的压敏特性。     

建筑工业化产品的系统论与装配式住宅设计

从建筑工业化产品的系统论出发,聚焦建筑设计方法与策略,结合装配式建筑系统集成特征,提出装配式建筑设计七个方面的设计策略,并分析其思路和相关手法.     

The effect of alkali metal oxide on the properties of borosilicate fireproof glass: Structure,thermal properties,viscosity, chemical stability

The purpose of the current work was to research the effect of alkali metal oxide on the structure, thermal properties, viscosity and chemical stability in the glass system (R₂O–CaO–B₂O₃–SiO₂) systematically. Because the glass would emulsify when Li₂O was added to the glass batch, this article did not discuss Li₂O. The results showed that when the amount of Na₂O was less than 4 mol.%, there was a higher interconnectivity of borate and silicate sub-networks in glass, as more mixed Si–O–B bonds were present in glass. The glass samples exhibited excellent thermal properties and chemical stabilities. As the amount of Na₂O exceeded 4 mol.%, the interconnectivity of borate and silicate sub-networks was weakened. The thermal properties and chemical stabilities of the glass samples were reduced. The connectivity of the silicate sub-network was weakened slightly as the Na/K ratio varied, and the coefficient of thermal expansion (CTE) of the glass samples gradually increased, and the resistance to thermal shock (RTS) value gradually decreased. Moreover, the viscosity of the glass samples decreased with the ratio of Na/Si and Na/K increased.     

多孔SiO2分子巢制备多功能涤纶纤维试验研究

针对传统PET材料不具备抗菌、不耐洗等问题,以煎煮法为基础,以草珊瑚、艾叶和薄荷为原料,制备含植物活性成分的溶液,其具有抗菌、杀菌的作用;以溶胶-凝胶法为多孔材料制备方法,用十六烷基三甲基溴化铵、十二烷基苯磺酸钠表面活性剂为模板剂,正硅酸乙酯为有机硅源,氨水为催化剂,乙醇和乙醚为助溶剂,在水-乙醇-乙醚体系中合成多孔二氧化硅微球;然后,多孔二氧化硅微球与提取液混合制备含植物活性成分的多孔二氧化硅分子巢;最后以制备的多孔二氧化硅分子巢与普通的聚酯切片用熔融纺丝工艺进行造粒、纺丝,得到具有抗菌、杀菌和耐洗的多功能涤纶纤维.通过SEM微观观察和力学性能测试、抗菌试验、耐洗性测试,对上述制备的多功能涤纶纤维性能进行验证.结果表明:在模板剂总浓度为0.029 mol·L-1、V醇:V醚=20:20、两种表面活性剂比为4:1时,得到的多孔SiO2微球排列规整;当多孔二氧化硅分子巢掺量(质量分数)在0.5％～1％时,通过熔融共混纺丝得到的新型多功能涤纶纤维力学性能表现最优;当多孔二氧化硅分子巢掺量(质量分数)在1％时,得到的新型多功能涤纶纤维的抗菌性能达到87.9％.而二氧化硅分子巢掺量越高,纤维材料越耐洗.以上结果说明本试验制备涤纶纤维的方案可行.     

Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

中药桂枝总黄酮的提取工艺研究

优化桂枝总黄酮的提取工艺，建立桂枝的提取和含量测定方法。通过单因素试验，考察提取方法、提取溶剂浓度、提取体积、提取时间对药材总黄酮含量的影响，采用正交试验，优化提取工艺条件，筛选出桂枝总黄酮的最佳提取工艺。总黄酮最佳提取工艺为75%乙醇、料液比1:40、回流提取时间60 min。该方法能有效测定桂枝药材总黄酮的含量，为该药材的质量标准研究提供一定的科学依据。本方法重复性较好、方法稳定、可行。     

中国智能机械制造评价及发展研究

以中国规模以上工业企业数据库为基础，结合在智能制造主要区域调研的结果，筛选出15145家智能制造企业，经同行评议后，生成322家候选企业名单；再由资深产业专家从“开发式创新”和“探索式创新”两个方面去考察候选企业的能力，得到中国智能制造百强排行榜；随后根据行业分类，得到智能机械制造企业排行榜。在概述了智能机械制造上榜企业的基本情况后，着重分析了前20强企业，并提出了中国智能机械制造发展路径和未来的发展趋势。