Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

Effects of (Li0.5Sm0.5)/W co-substitution and sintering temperature on the structure and electrical properties of ultrahigh Curie temperature piezoceramics,Ca0.92(Li0.5Sm0.5)0.08Bi2Nb2-xWxO9

With co-substitution of (Li_0.5Sm_0.5) at A site and W at B site, the electrical properties of modified Ca_0.92(Li_0.5Sm_0.5)_0.08Bi₂Nb_2-xW_xO₉ [(CLS)BN-xW, x = 0, 0.015 and 0.03] piezoceramics with ultrahigh Curie temperature (T_C) of > 930 °C were enhanced dramatically. The increased resistivity induced by the co-substitution ensure them to be polarized under an enough high field. Combined with the increase of spontaneous ferroelectric polarization (P_S), the significant enhancements in the piezoelectric, dielectric and ferroelectric properties can be obtained in the composition x = 0.015. Furthermore, the piezoelectric activity (d₃₃) and bulk resistivity (ρ_b) of (CLS)BN-0.015 W can be further enhanced at an appropriate sintering temperature. This optimum composition sintered at 1170 °C shows ultrahigh T_C of ～948 °C, d₃₃ of ～17.3 pC/N and ρ_b of ～6.9 MΩ cm at 600 °C, which are comparable to those of the reported high-temperature Aurivillius piezoceramics with T_C > 850 °C.     

Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

Constructing magnetically recoverable CdS/CaFe2O4 P–N heterojunctions for enhanced photoelectrochemical properties towards H2 evolution reaction

A novel CdS/CaFe₂O₄ (CS/CFO) heterogeneous p-n junction was created by thermal deposition of CaFe₂O₄ nanoparticles on CdS rods. The CS/CFO hetero-structured photocatalysts exhibited increasingly efficient visible light harvesting compared to the bare CdS. The CS/CFO composites also presented higher photocurrent and slower decay of photoluminescence, suggesting a better separation of the photo-generated electrons and holes. The photocatalytic H₂ evolution quantity on the optimized CS/CFO composite from water in the presence of ethanol was up to 2200 μmol after 3-h visible light illumination, which is more than twice that of the pristine CdS. The chemical interaction between CdS and CaFe₂O₄ was confirmed by the shifts in the XPS peaks, which made it possible for the charge carriers to transfer across the p-n junction interface. This research highlights the importance of forming an interfacial p-n heterojunction between two semiconductors for efficient charge separation and improved photocatalytic performance.     

基于图神经网络的网络性能智能预测

传统网络性能预测技术存在网络状态获取不够全面及网络性能评估准确性欠佳等问题，利用图神经网络学习推理网络关系数据的特点，结合捕获的网络全局信息，提出了一种基于图神经网络的网络性能智能预测方法。通过网络系统抽象及网络性能建模，将复杂的网络信息转化为形式化的图数据进行描述，利用图空域卷积处理图网络节点的消息传递过程，实现网络信息之间的关系推理，研究了实现网络性能预测的图神经网络模型，提出了一种能处理流量矩阵、网络拓扑、路由策略、节点配置的图神经网络体系结构，最后通过实验论证了模型能更好地实现包括时延、抖动和丢包率的网络性能的准确预测。     

基于TRNSYS的茯砖茶生产工艺能源系统节能环保特性研究

茯砖茶发酵、干燥过程中，烘房内温湿度稳定性和能源系统低能耗是保证茯砖茶品质与成本的重要因素。本文采用TRNSYS仿真与实验研究相结合的方法，对咸阳某茯砖茶厂实际使用的空气源热泵系统进行建模，通过研究各季节典型代表月烘房温湿度的波动情况，确定该空气源热泵系统在全年的运行状态是否满足工艺要求，在此基础上，对比了该系统在全年可运行季节代表月与该生产厂房早期使用的燃气锅炉系统的能耗仿真结果，对空气源热泵系统的节能与环保特性进行研究。结果表明：由于夏季送风质量流量过大且室外空气含湿量较高，7月烘房温湿度不满足工艺要求。热泵系统在1、4、10月的总标煤消耗量的平均值是锅炉系统的44.42%，平均CO2、SO2、NOx排放量分别为锅炉系统的34.13%、44.1%、40.60%。在茯砖茶发酵、干燥的过程中，相比于燃气锅炉系统，空气源热泵系统具有更好的节能与环保特性。     

基于氮掺杂碳纳米颗粒荧光猝灭-恢复方法检测还原型谷胱甘肽

分别以海藻酸钠和色氨酸为碳源和氮源,采用固相法一步合成出了量子产率为47.9%的氮掺杂荧光碳纳米颗粒(N-CNPs)。根据铜离子存在的条件下,N-CNPs荧光强度的恢复情况与还原型谷胱甘肽浓度成正比的关系,建立基于N-CNPs检测还原型谷胱甘肽的新方法。优化了溶液pH及反应时间等条件。在pH 6.0、铜离子浓度30μmol/L条件下,谷胱甘肽在0.2~45μmol/L浓度范围内与N-CNPs荧光恢复强度呈良好的线性关系,检出限为50 nmol/L。方法具有灵敏度高、选择性好、操作简单等优点,可用于实际样品中谷胱甘肽的检测。     

儿童用品TBT通报数据可视化预警研究

探索采用数据可视化技术分析儿童用品TBT通报数据,以可视化图形图像呈现通报热点并揭示趋势信息,提出对策与建议,助力为儿童用品产业升级、TBT预警数据分析和信息传播工作提供新思路,提高中小企业的国外市场准入机会。