Characterizing physical habitat preferences and thermal refuge occupancy of brook trout (Salvelinus fontinalis) and Atlantic salmon (Salmo salar) at high river temperatures

Anthropogenic influences, including climate change, are increasing river temperatures in northern and temperate regions and threatening the thermal habitats of native salmonids. When river temperatures exceed the tolerance levels of brook trout and Atlantic salmon, individuals exhibit behavioural thermoregulation by seeking out cold‐water refugia – often created by tributaries and groundwater discharge. Thermal infrared (TIR) imagery was used to map cold‐water anomalies along a 53 km reach of the Cains River, New Brunswick. Trout and salmon parr did not use all identified thermal anomalies as refugia during higher river temperature periods (>21°C). Most small‐bodied trout (8–30 cm) were observed in 80% of the thermal anomalies sampled. Large‐bodied trout (>35 cm) required a more specific set of physical habitat conditions for suitable refugia, that is, 100% of observed large trout used 30% of the anomalies sampled and required water depths >65 cm within or adjacent to the anomaly. Densities of trout were significantly higher within anomalies compared with areas of ambient river temperature. Salmon parr were less aligned with thermal anomalies at the observed temperatures, that is, 59% were found in 65% of the sampled anomalies; and densities were not significantly different within/ outside anomalies. Salmon parr appeared to aggregate at 27°C, and after several events over 27°C variability in aggregation behaviour was observed – some fish aggregated at 25°C, others did not. We stipulate this is due to variances of thermal fatigue. Habitat suitability curves were developed for velocity, temperature, depth, substrate, and deep water availability to characterize conditions preferred by fish during high‐temperature events. These findings are useful for managers as our climate warms, and can potentially be used as a tool to help conserve and enhance thermal refugia for brook trout and Atlantic salmon in similar systems.     

Real-time organic aerosol chemical speciation in the indoor environment using extractive electrospray ionization mass spectrometry

Understanding the sources and composition of organic aerosol (OA) in indoor environments requires rapid measurements, since many emissions and processes have short timescales. However, real-time molecular-level OA measurements have not been reported indoors. Here, we present quantitative measurements, at a time resolution of five seconds, of molecular ions corresponding to diverse aerosol-phase species, by applying extractive electrospray ionization mass spectrometry (EESI-MS) to indoor air analysis for the first time, as part of the highly instrumented HOMEChem field study. We demonstrate how the complex spectra of EESI-MS are screened in order to extract chemical information and investigate the possibility of interference from gas-phase semivolatile species. During experiments that simulated the Thanksgiving US holiday meal preparation, EESI-MS quantified multiple species, including fatty acids, carbohydrates, siloxanes, and phthalates. Intercomparisons with Aerosol Mass Spectrometer (AMS) and Scanning Mobility Particle Sizer suggest that EESI-MS quantified a large fraction of OA. Comparisons with FIGAERO-CIMS shows similar signal levels and good correlation, with a range of 100 for the relative sensitivities. Comparisons with SV-TAG for phthalates and with SV-TAG and AMS for total siloxanes also show strong correlation. EESI-MS observations can be used with gas-phase measurements to identify co-emitted gas- and aerosol-phase species, and this is demonstrated using complementary gas-phase PTR-MS observations.     

2.4 GHz continuously variable ferroelectric phase shifters using all-pass networks

Continuously variable ferroelectric (BST on sapphire) phase shifters based on all-pass networks are presented. An all-pass network phase shifter consists of only lumped LC elements, and thus the total size of the phase shifter is kept to less than 2.2 mm /spl times/ 2.6 mm at 2.4 GHz. The tunability (C/sub max//C/sub min/) of a BST interdigital capacitor is over 2.9 with a bias voltage of 140 V. The phase shifter provides more than 121/spl deg/ phase shift with the maximum insertion loss of 1.8 dB and the worst case return loss of 12.5 dB from 2.4 GHz to 2.5 GHz. By cascading two identical phase shifters, more than 255/spl deg/ phase shift is obtained with the maximum insertion loss of 3.75 dB. The loss figure-of-merit of both the single- and double-section phase shifters is over 65/spl deg//dB from 2.4 GHz to 2.5 GHz.     

如何用硅振荡器替代晶体和陶瓷谐振器

对于绝大多数微控制器时钟电路而言，硅振荡器是一种简单且有效的解决方案。与晶体和陶瓷谐振器不同，基于硅材料的定时器具有抗振动、抗撞击和抗电磁干扰的优点。同时，硅振荡器不需要严格匹配的定时元件和线路板走线。     

Electrical linewidth test structures fabricated in monocrystallinefilms for reference-material applications

The physical widths of reference features incorporated into electrical linewidth test structures patterned in films of monocrystalline silicon have been determined from Kelvin voltage measurements. The films in which the test structures are patterned are electrically insulated from the bulk-silicon substrate by a layer of silicon dioxide provided by SIMOX (Separation by the IMplantation of OXygen) processing. The motivation is to facilitate the development of linewidth reference materials for critical-dimension (CD) metrology-instrument calibration. The selection of the (110) orientation of the starting silicon and the orientation of the structures' features relative to the crystal lattice enable a lattice-plane-selective etch to generate reference-feature properties of rectangular cross section and atomically planar sidewalls. These properties are highly desirable for CD applications in which feature widths are certified with nanometer-level uncertainty for use by a diverse range of CD instruments. End applications include the development and calibration of new generations of CD instruments directed at controlling processes for manufacturing devices having sub-quarter-micrometer features     

An adaptive descent method for non-linear viscoplasticity

A forming model based on a viscoplastic flow formulation is derived which includes the effects of small elastic strains. A significant feature of the formulation is its reliance on the dominant inelastic material characteristics in the formation of the stiffness matrix for large strain problems. The resultant non-linear system of equations is solved by an adaptive descent method which combines the rapid convergence of Newton's method near the solution with the robustness of a method of successive approximations. The use of the adaptive descent method effectively extends the viscoplastic flow formulations into the nearly rate-insensitive range of behaviours exhibited, for example, by metals at low temperature, where slow convergence of the non-linear solution algorithm has traditionally hampered their use.