Linear regression-based multifidelity surrogate for disturbance amplification in multiphase explosion

Structural and Multidisciplinary Optimization - When simulations are very expensive and many are required, as for optimization or uncertainty quantification, a way to reduce cost is using...     

Flame extension and the near field under the ceiling for travelling fires inside large compartments

Structures need to be designed to maintain their stability in the event of a fire. The travelling fire methodology (TFM) defines the thermal boundary condition for structural design of large compartments of fires that do not flashover, considering near field and far field regions. TFM assumes a near field temperature of 1200°C, where the flame is impinging on the ceiling without any extension and gives the temperature of the hot gases in the far field from Alpert correlations. This paper revisits the near field assumptions of the TFM and, for the first time, includes horizontal flame extension under the ceiling, which affects the heating exposure of the structural members thus their load-bearing capacity. It also formulates the thermal boundary condition in terms of heat flux rather than in terms of temperature as it is used in TFM, which allows for a more formal treatment of heat transfer. The Hasemi, Wakamatsu, and Lattimer models of heat flux from flame are investigated for the near field. The methodology is applied to an open-plan generic office compartment with a floor area of 960 m² and 3.60 m high with concrete and with protected and unprotected steel structural members. The near field length with flame extension (fTFM) is found to be between 1.5 and 6.5 times longer than without flame extension. The duration of the exposure to peak heat flux depends on the flame length, which is 53 min for fTFM compared with 17 min for TFM, in the case of a slow 5% floor area fire. The peak heat flux is from 112 to 236 kW/m² for the majority of fire sizes using the Wakamatsu model and from 80 to 120 kW/m² for the Hasemi and Lattimer models, compared with 215 to 228 kW/m² for TFM. The results show that for all cases, TFM results in higher structural temperatures compared with different fTFM models (600°C for concrete rebar and 800°C for protected steel beam), except for the Wakamatsu model that for small fires, leads to approximately 20% higher temperatures than TFM. These findings mitigate the uncertainty around the TFM near field model and confirm that it is conservative for calculation of the thermal load on structures. This study contributes to the creation of design tools for better structural fire engineering.     

On the efficiency of quantization-based integration methods for building simulation

Models describing energy consumption, heating, and cooling of buildings usually impose difficulties to the numerical integration algorithms used to simulate them. Stiffness and the presence of frequent discontinuities are among the main causes of those difficulties, that become critical when the models grow in size. Quantized State Systems (QSS) methods are a family of numerical integration algorithms that can efficiently handle discontinuities and stiffness in large models. For this reason, they are promising candidates for overcoming the mentioned problems. Based on this observation, this article studies the performance of QSS methods in some systems that are relevant to the field of building simulation. The study includes a performance comparison of different QSS algorithms against state-of-the-art classic numerical solvers, showing that the former can be more than one order of magnitude faster.     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

Hierarchical micro-nanostructured albite-based glass-ceramic for high dielectric strength insulators

A novel glass-ceramic material based on albite type Na-rich feldspar has been synthesized by conventional ceramic process. High crystallinity, >94%?Vol.% is obtained by fast sintering which allows energy saving processing. Albite is the main crystalline phase and tetragonal SiO₂ is a secondary phase. Electrical properties were examined by complex impedance, DC measurements, and dielectric breakdown test. Dielectric characterization shows a non-Debye type dielectric behavior with low dielectric constant, 4.6 at 1?MHz, low dielectric losses, (～10^?3 at 1?MHz, and a large dielectric strength, ～60?kV/mm), that it is the largest value reported in ceramic insulators. Those dielectric properties are attained by the low glassy phase content in the samples and their unique micro-nanostructure. All these properties make this novel material a very promising candidate in the market of ceramic electrical insulator, highlighting for high-voltage applications.     

Microbial Fuel Cell Application for Azoic Dye Decolorization with Simultaneous Bioenergy Production Using Stenotrophomonas sp.

A single‐chamber air‐cathode microbial fuel cell (MFC) was successfully applied for decolorization of the diazoic dye Reactive Black 5 (RB5) with simultaneous production of electricity. An innovative low‐cost medium, the marine water‐glucose‐yeast extract medium (MWGY), was developed which appears as a textile marine effluent in terms of salinity. The anode compartment containing a single bacterial strain of Stenotrophomonas sp. showed almost complete dye decolorization with different RB5 concentrations after seven days of treatment. For the four dye concentrations used, a correlation between dye removal and production of electrical energy was found. The comparison of the decolorization process in the MFC with that in a batch reactor as control experiment highlights the efficiency of the single‐chamber air‐cathode MFC technology which improved the dye removal by the same bacterial strain.     

Correction to: EKLT: Asynchronous Photometric Feature Tracking Using Events and Frames

International Journal of Computer Vision - The original version of this article was unfortunately omitted to publish the footnote “The best result per row is highlighted in bold” in...