Geo- and Hydro-Mechanical Evaluation of Slope Failure Induced by Torrential Rains in Northern-Kyushu Area,July 2009

Torrential rainfall in mid-July 2009 triggered numerous geodisasters such as slope failure and debris flow in Chugoku and Northern Kyushu areas of Japan. A number of slope failures and debris flows occurred in Yamaguchi and Fukuoka prefectures resulting in extensive damage to human life and infrastructure. One of the most serious geodisasters included a slope failure followed by debris flow at Sasaguri-machi and Fukuchi-machi, Fukuoka prefecture, Japan. This paper summarizes the results of geotechnical investigations on the geodisaster sites in Fukuoka prefecture. The geotechnical investigation included determining a series of grain size distributions, consistency limits and conducting direct box shear tests for collapsed soils collected at six disaster sites. The generation mechanisms of slope failure followed by debris flow were also investigated by analyzing the precipitation, topography, geology, and strength properties of the collapsed soils. Moreover, slope deformation and stability analyses were coupled with an unsaturated-saturated seepage analysis to investigate the slope failure mechanism. The main findings from the study are summarized as: The physical properties, such as the grain size distribution, the plastic limit and liquid limit of collapsed soils, are summarized and compared with the results of other failure slopes in the literature. The collapsed soil was characterized as being a well grained soil (the uniformity coefficient >50) and highly weathered (the ignition loss >5%), however, with regard to the liquid limit and plastic index, there were no remarkable findings. The original shear strength for collapsed soils with natural water content is relatively large and slope failure doesn't occur because the cohesion in the shear strength is induced by a suction force between the soil particles under unsaturated condition. However, water seepage into the soil induces a drastic decrease in the shear strength, which is mainly caused by a decrease in cohesion (losing suction) resulting from soil saturation. In addition, the drained/undrained condition in the shear process is also sensitive to shear strength. For example, both water seepage and the shear process with constant volume cause an approximate 30% reduction in shear strength for Fukuchi-machi and Sasaguri-machi soil samples. Therefore, the reduction of cohesive strength due to water seepage and the low permeability of the slope are the parameters which trigger geodisaster. Based on the results of slope deformation and a stability analyses which took the change in water pressure and cohesive strength into account, the geodisaster at Fukuchi-machi was simulated, it is reasonable to assume that the shallow failure near the top of slope occurred due to torrential precipitation of about 100 mm per hour which triggered a debris flow.     

Characterization of polystyrene-binding peptides (PS-tags) for site-specific immobilization of proteins

In this study, we characterized polystyrene-binding peptides (PS-tags) that possess a specific binding affinity for hydrophilic polystyrene (phi-PS) plates. Both the FITC-labeled PS19-1 (RAFIASRRIKRP) and PS19-6 (RIIIRRIRR) peptides showed strong binding affinity for commercially available hydrophilic, but not hydrophobic, PS plates in the presence of the non-ionic surfactant Tween 20. The dissociation constants (K_d) of the PS19-1 and PS19-6 peptides for the hydrophilic PS-A plate were 169 and 86 nM, respectively, and the K_d of both peptides increased with the concentration of NaCl or urea. Based on adsorption yield and residual activity of glutathione S-transferase (GST) after fusion with the PS19-6 peptide or its variants, it was found that the basic amino acid in the PS-tags, i.e., Arg was essential for the strong binding affinity of PS-tags in both the peptide and peptide-fused protein forms The aliphatic amino acids in PS19-6 and PS19-6L, such as Ile or Leu, were also effective. Thus, a series of PS-tags that possess this unusual feature, especially the peptides PS19-6 (RIIIRRIRR) and PS19-6L (RLLLRRLRR), are potential candidate affinity peptide tags for site-specific immobilization of proteins onto hydrophilic PS plates, which show potential as solid supports for protein-based biochips.     

Liquid phase growth of graphene on silicon carbide

We developed a novel method to produce graphene on silicon carbide (SiC) at a temperature as low as 1000 °C. The method is based on liquid phase growth (LPG) of graphene mediated by liquid gallium, which acts not only as a flux to store carbon dissolved from a surface of SiC when heated, but also as a catalyst to promote the formation of graphene on SiC when cooled. Our experimental results revealed that gallium-treated SiC substrates are coated with uniform and continuous graphene films. The LPG method is able to supply graphene films consisting of one to several hundreds of layers, depending on heating temperatures. Our approach can not only provide an alternative way to form graphene natively on SiC, but will also bring a technological breakthrough in industrial applications of graphene, e.g. the realization of graphene-on-insulator substrates.     

Gas entrainment rate and flow pattern of vertical plunging liquid jets

For a vertical plunging liquid jet system using various liquids, the effects of the operating conditions including the nozzle length-to-diameter ratio on the gas entrainment rate Q_g were evaluated experimentally. The differences in Q_g were related to the changes in the jet shape before plunging and the velocity of the plunging liquid jet at the point where the gas sheath breaks up. Empirical relationships were also presented to predict the maximum depth Z of bubbles entrained by the diffusing jet. The changes of Z were further discussed in terms of the downward liquid velocity distribution in the submerged two-phase region, which depends mainly on the size of entrained bubbles.     

Effects of species and moisture content on penetration of liquid in laser incised lumber by the passive impregnation method

Penetration of liquid by passive impregnation method for Douglas-fir (Pseudotsuga menziesii Franco), sugi (Cryptomeria japonica D. Don) and Japanese larch (Larix leptolepis Gordon) was studied. Effects of initial moisture content of sugi (16, 43 and 70% moisture content) on liquid penetration were also studied. Dried Douglas-fir (mc=14%) and sugi (mc=16%), and green Japanese larch (mc=45%) and sugi (mc=70%) were treated by passive impregnation method for penetration analysis. It was observed that dried sugi had the highest level of liquid penetration both in length (170 mm) and width (8 mm) for all measured sections followed by green sugi, green Japanese larch and dried Douglas-fir. In case of different initial moisture content, the highest absorption (624 kg/m³) and penetration (maximum 87 and 96% at cross and longitudinal surfaces, respectively) was observed for sugi having the lowest initial moisture content under the same passive impregnation conditions. Absorption and penetration decreased with the increase of initial moisture content for sugi. These results could help in designing incising pattern and density, as well as solving the problems related to high initial moisture content of wood for passive impregnation.     

Selective carbon monoxide adsorbent composed of polystyrene resin having amino groups and copper(I) chloride

A carbon monoxide adsorbent composed of 10 g of a polystyrene resin having amino groups and 70 mmol of copper(I) chloride was prepared by refluxing the resin and copper(I) chloride in acetonitrile, followed by evaporation of the liquid phase at 5 mmHg, 80°C. The adsorbent rapidly adsorbs 15.9 mmol of carbon monoxide under 1 atm at 20°C. 11.4 mmol of adsorbed carbon monoxide are desorbed when the adsorbent is subjected to a reduced pressure (5 mmHg) at 80°C for 10 min. In the second and the later adsorptions, the amount of adsorbed carbon monoxide is virtually constant at 11.4 mmol. The amount of carbon dioxide adsorbed by the adsorbent under 1 atm at 20°C is 2.8 mmol, and the value for methane is 0.0 mmol. The prepared adsorbent is applicable to selective separation of carbon monoxide from gas mixtures containing both carbon dioxide and methane.     

Isotachophoretic analysis of surfactants

The qualitative and quantitative determination of anionic surfactants (sodium and lithium alkylsulfate, sodium dodecylbenzenesulfonate, sodium di-2-ethylhexyl sulfosuccinate, sodium and lithium perfluoroalkylcarboxylate, and lithium perfluorooctanesulfonate) were investigated by a capillary tube isotachophoresis using a potential gradient detector. The leading electrolyte solution was the mixture of acetonitrile and aqueous solution of histidine buffer containing calcium chloride. The terminating electrolyte solution was the aqueous solution of sodium octanoate. These electrolytes were effective for the analysis of the mixtures of strongly acidic surfactants.     

Late phase II trial of oral etoposide administered for 21 consecutive days in patients with cervical cancer. ETP 21 Study Group--Cervical Cancer Group

We conducted a multi-site late phase II trial of oral etoposide administered for 21 consecutive days in patients with cervical cancer in cooperation with 32 institutes. Fifty mg/body of oral etoposide was administered daily for 21 consecutive days. Treatment cycles were to be repeated at 4- to 5-week intervals. Eighty patients were enrolled and 70 patients were evaluated. The overall response rate (95% CI), including one complete response patient and 18 partial response patients, was 27.1% (19/70). The most commonly observed toxicity was myelosuppression such as leukopenia, neutropenia, hemoglobin decrease and thrombocytopenia. Other adverse effects were gastrointestinal toxicities such as anorexia, nausea, stomatitis and vomiting, as well as fatigue and alopecia. These adverse effects were well tolerated and controlled with medications. From these results we concluded oral etoposide administered for 21 consecutive days was an effective drug against cervical cancer.     

Cooperative behavior of various agents in dynamic environment

The multi-agent model is a model in which agents with limited ability cooperate each other to accomplish a goal. In this paper, we introduce a multi-agent model in which agents are created to imitate real ants. There are two different type of agents, each type of which has a particular task. We designed agents to communicate each other by using pheromone considering noise. On this model, we observed cooperative behavior of agents and evaluated conditions to make an order of behavior in the model.     

Compatibility between several heat resistant alloys and sintered Li2O in static helium gas environment

The reaction of sintered Li₂O discs with several commercial heat resistant alloys has been investigated under the conditions of 3.3 × 10⁴Pa ($\text{1}\text{3}\text{atm}$) static He gas atmosphere in the temperature range of 500 and 750° C. Reaction products were identified by X-ray diffraction analysis to be two phases of Li₅FeO₄ and LiCrO₂. The former was dominant below 650° C and the latter was dominant above 650° C. The activation energies of the reaction were determined by the Arrhenius plots for weight changes and sub-scale thickness measurements. The reactivity of the four Fe-Ni-Cr alloys decreased according to the order of Incoloy 800, 316 SS, Hastelloy X-R and Inconel 600. Grain boundary penetration was observed above 500° C for Incoloy 800, 550° C for 316 SS and 600° C for Inconel 600. There was no grain boundary penetration in Hastelloy X-R.