Fabrication of dense Ce0.9Mg0.1P2O7-PmOn composites by microwave heating for application as electrolyte in intermediate-temperature fuel cells

In the present work, we report a method of fabrication of dense 10 mol% Mg²⁺-doped cerium pyrophosphate-phosphate (Ce_0.9Mg_0.1P₂O₇-P_mO_n; CMP-P) composites by microwave heat-treatment of the preformed Ce_0.9Mg_0.1P₂O₇ substrates in the presence of phosphoric acid. The composite was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The microwave heating at 375 °C for 5 min resulted in the formation of dense CMP-P composites which retained most of the pyrophosphate phase. The electrical conductivity was extracted from the EIS data and for the CMP-P composite prepared by H₃PO₄ loading for 10 h and microwave heat-treatment for 5 min it was found to be >10^?2 S m^?1 in 100–250 °C range with a maximum of 0.062 S cm^?1 at 190 °C, which was significant for its application as electrolyte in intermediate temperature fuel cells.     

A Survey on Advanced Multiple Access Techniques for 5G and Beyond Wireless Communications

Wireless Personal Communications - This paper summarizes the ongoing research initiatives based on the advanced multiple access techniques towards the fifth generation (5G) wireless communication...     

Life Cycle Assessment of Wire Rope Used in Crane Application in a Steel Plant

Journal of Failure Analysis and Prevention - Wire rope is an important part of any crane. Failure of wire rope may lead to major loss in terms of life and cost. Wire rope failures are attributed by...     

Modelling and kinetic aspects of a BTEX contaminated air-treating biofilter

In this study, the overall performance of a biofilter was evaluated in terms of its elimination capacity by using 3-D mesh techniques. The overall results indicate that the agreement between experimental data and model predictions is excellent for benzene, toluene, ethylbenzene and o-xylene (BTEX). In this study, the maximum removal rate (r _max) values for BTEX were 0.0117, 0.0126, 0.0081 and 0.0146 g m^–3 h^–1, and the half-saturation constant (K_S ) values were calculated to be 0.269, 0.297, 0.156 and 0.394 g m^–3, respectively. For this system, the coefficients of determination (r ²) of BTEX compounds were greater than 0.97. The BTEX concentration profiles along the depth were also determined using a convection–diffusion reactor (CDR) model. The sums of squares of the errors (SSEs) of BTEX were 0.0078, 0.0059, 0.0129 and 0.0269, respectively, with r ² values greater than 0.99 for all four compounds at low concentrations.     

Strategies for the construction sector in the information technology era

The construction industries in many countries are starting to consider seriously the strategic use of information technology (IT). The use of information technology in construction is extending beyond the stage of piecemeal application for improving the efficiency of discrete operations by individual organizations to the advanced stage where IT is applied strategically in commercial enterprises, government agencies and professional institutions. Progress in construction in this regard appears to lag behind that in most other sectors of the economy. This paper considers the nature and the background of this progression in construction by examining proposals by Earl (1989) of nine basic prerequisites to the IT era which make a strategic approach timely. Each prerequisite is outlined and how it has been met in other sectors of the economy considered. The extent to which these prerequisites apply in construction and the scope for their application in the near future are examined. It is argued that all organizations involved in construction will ultimately have to think strategically about their use of IT, and how some are already doing so is described.

In discussing the factors which hinder the strategic application of IT in construction, the nature of the design and construction processes and initiatives that may be necessary to overcome the perceived problems are examined in detail. The strategies that are evolving at a national level in Singapore are outlined.     

Enhancement of corrosion protection of 3-glycidoxypropyltrimethoxysilane-based sol–gel coating through methylthiourea doping

Protection of aluminum metal and its alloys from corrosion is a key requirement for many engineering applications. Nowadays, sol–gel coating technology is recognized as the ideal replacement for chromate conversion coatings. The present work makes use of 3-glycidoxypropyltrimethoxysilane (GPTMS) as a precursor for sol–gel coating. GPTMS was subjected to hydrolysis and subsequent condensation reaction to get a three-dimensional network and methylthiourea (MTU) was incorporated into the sol–gel matrix. MTU-doped GPTMS-based sol–gel coatings were applied over aluminum metal by dip coating method. The resultant coating was studied by FTIR, XRD and SEM. MTU-doped GPTMS-based sol–gel coatings increased the hydrophobic nature of the coating and were stable up to a temperature of 450°C. The protective nature of the coatings was evaluated in a 1% NaCl environment using electrochemical impedance and polarization studies. The study has revealed that doping of MTU enhanced the protection ability of doped GPTMS-based sol–gel coating to a significant extent.     

Pinch Roller Failure Analysis and Resulting Enhancement of Rebar Mechanical Properties

Reinforcing bars, popularly termed “rebars,” are used to impart tensile strength to concrete structures. Concrete has high resistance to weathering and fire and high compressive strength but almost no tensile strength, hence rebars are used to provide the latter to concrete. Property consistency along the length of rebars is an important prerequisite. When the finished product is subjected to thermomechanical treatment (TMT), proper control of rolling and water box parameters and efficient pinch rolling are needed to achieve acceptable properties. Variation of yield strength (YS) along TMT bars from the front to back end has been observed within the same heat treatment. In the presented investigation, it was observed that pinch rolling ineffectiveness is the main reason for the poor mechanical properties at the back end. The pinch roller was unable to support the back end of the TMT bars properly to maintain the speed and tension of the bars, resulting in nonuniform cooling of the back end through the water box and subsequent mechanical property failure. Due to the substandard material of the pinch roller, it was unable to hold the back end of the bar properly. Based on analysis of the roller it was concluded that it failed due to improper microstructure, resulting in inadequate hardness and toughness for the stringent operating conditions. AISI H13 is a better material to use in such high-service-temperature conditions. Moreover, proper heat treatment is needed to achieve adequate hardness and microstructure properties. After proper heat treatment of pinch rollers, their service life was increased twofold, minimizing the YS variation along the rebars.     

Development and analysis of a tool for speed up of EnergyPlus through parallelization

This paper describes how the EPparallel tool splits a single annual simulation into 12 simulations of one month each and runs them in parallel. The paper also describes the methodology to prepare input files, enable file sharing between nodes, collate results generated by the nodes, and ensure quality check on the simulations. The EPparallel tool uses Message Passing Interface library and runs on Linux. The tool has been tested on 16 commercial reference buildings over 16 US weather files. The results of these 256 runs which include the run times, computing time overheads, speed gains and accuracy of results are presented in this paper. The speed gain ranged from 2.9×to 7.8×and deviation (percentage of output values obtained in parallel simulation which were off by more than 1% as compared to output values obtained in annual simulation) ranged from 0% to 4%.