Radiation and slip effects on MHD Maxwell nanofluid flow over an inclined surface with chemical reaction

The numerical solutions of the upper-convected Maxwell (UCM) nanofluid flow under the magnetic field effects over an inclined stretching sheet has been worked out. This model has the tendency to elaborate on the characteristics of “relaxation time” for the fluid flow. Special consideration has been given to the impact of nonlinear velocity slip, thermal radiation and heat generation. To study the heat transfer, the modified Fourier and Fick's laws are incorporated in the modeling process. The mass transfer phenomenon is investigated under the effects of chemical reaction, Brownian motion and thermophoresis. With the aid of the similarity transformations, the governing equations in the ordinary differential form are determined and then solved through the MATLAB's package “bvp4c” numerically. This study also brings into the spotlight such crucial physical parameters, which are inevitable for describing the flow and heat transfer behavior. This has been done through graphs and tables with as much precision and exactitude as is possible. The ascending values of the magnetic parameter, the Maxwell parameter and the angle of the inclined stretching sheet cause decay in the dimensionless velocity while an assisting behavior of the thermal and concentration buoyancy parameters is noticed.     

Perovskite SrFe1-xTixO3-δ (x < = 0.1) cathode for low temperature solid oxide fuel cell

Stable and compatible cathode materials are a key factor for realizing the low-temperature (LT, ≤600?°C) operation and practical implementations of solid oxide fuel cells (SOFCs). In this study, perovskite oxides SrFe_1-xTi_xO_3-δ (x?< = 0.1), with various ratios of Ti doping, are prepared by a sol-gel method for cathode material for LT-SOFCs. The structure, morphology and thermo-gravimetric characteristics of the resultant SFT powders are investigated. It is found that the Ti is successfully doped into SrFeO_3-δ to form a single phase cubic perovskite structure and crystal structure of SFT shows better stability than SrFeO_3-δ. The dc electrical conductivity and electrochemical properties of SFT are measured and analysed by four-probe and electrochemical impedance spectra (EIS) measurements, respectively. The obtained SFT exhibits a very low polarization resistance (R_p), .01 Ωcm² at 600?C. The SFT powders using as cathode in fuel cell devices, exhibit maximum power density of 551?mW?cm^?2 with open circuit voltage (OCV) of 1.15?V at 600?C. The good performance of the SFT cathode indicates a high rate of oxygen diffusion through the material at cathode. By enabling operation at low temperatures, SFT cathodes may result in a practical implementation of SOFCs.     

Application of GA-Optimized ANNs to Predict the Water Content,CO2 and H2S Absorption Capacity of Diethanolamine (DEA) in Khangiran Gas Sweetening Plant

Theoretical Foundations of Chemical Engineering - In this work, with the aim of accurate prediction of water content, H2S and CO2 absorption capacity of diethanolamine (DEA) solvent in Khangiran...     

Antioxidant potential of extracts from peels and stems of yellow-fleshed and white cassava varieties

This study focused on the exploration of the potentials of extracting antioxidants from peels and stems of yellow-fleshed and white cassava varieties. The effect of particle size (0.2 and 0.5 mm) and variety on the phenolic content and antioxidant activity was assessed. The peels of the yellow-fleshed cassava variety with a particle size of 0.2 mm showed the highest phenolic content with 681.5 GAE mg 100 g⁻¹ and antioxidant activity of 19% and 425 μM TE g⁻¹ dry matter using DPPH and FRAP assays respectively. The stems of the white cassava with a particle size of 0.2 mm exhibited high phenolic content (442.4 GAE mg 100 g⁻¹) and antioxidant activity of 12.8% and 234 μM TE g⁻¹, better than the stem of the yellow-fleshed cassava. These results indicate that phenolic and antioxidant extractions were influenced by variety, the plant parts and particle size for the antioxidant assays.     

Micro‐morphological,environmental and phytochemical investigation of herbal medicines by using LM and SEM: A quality control tool

The use of quality control tool for authentication of Jadwar (Delphinium denudatum Wall. ex Hook.f. & Thomson), a folk herbal drug used for the treatment of different ailments, was studied. People face problems of adulteration for this drug at global, regional, national and local levels. Two different plant species are commercially marketed in the Indo‐Pak Subcontinent under the same trade name of Jadwar. One is D. denudatum Wall. ex Hook.f. & Thomson and the other is Aconitum heterophyllum Wall. ex Royle. To focus on this problem, a marketable available drug sample of Jadwar was authenticated by using basic microscopy tools (LM) and advanced chemo‐taxonomic markers. Authentication, quality and standardization of this drug was achieved using morphology, organoleptography, UV and IR analyses, scanning electron microscopy of pollen and anatomical investigations. The techniques used for authentication marked the clear difference between the studied plants. Microscopic studies, chemotaxonomic investigation and other techniques used in this project provided the basis for the authentication of this species.