Suggestions to the article: medical professionalism research characteristics and hotspots

Scientometrics - The article published on 5 July 2021 is well-written and of interest. However, some improvements could be made, such as ten Tables/Figures can be shortened to highlight the focused...     

Improvement of dielectric breakdown strength and energy storage performance in Er2O3–modified 0.95Sr0.7Ba0.3Nb2O6-0.05CaTiO3 lead-free ceramics

In this study, 0.95?Sr_0.7Ba_0.3Nb₂O₆-0.05CaTiO₃-x wt% Er₂O₃ ceramics (SBNCTEx; x?=?0–5) were synthesized using traditional solid-state method, and we investigated the microstructure, energy storage properties as well as the relationship between dielectric breakdown strength and interfacial polarization. As compared with pure 0.95?Sr_0.7Ba_0.3Nb₂O₆-0.05CaTiO₃ ceramics, the Er₂O₃ dopants suppressed the grain growth of SBNCTEx, and the doped ones showed the dense microstructure. The secondary phase was found for x?≥?1 according to the EDS results, and the influence of the secondary phase on relative dielectric breakdown strength has also been studied. The dielectric breakdown strength increased from 18.1?kV/mm to 34.4?kV/mm, which is good for energy storage. The energy storage density of 0.28?J/cm³ and the energy storage efficiency of 91.4% were obtained in the SBNCTE5 ceramics. The results indicate that SBNCTE ceramics can be used as energy storage capacitors.     

Stabilizing temperature-capacitance dependence of (Sr,Pb, Bi)TiO3-Bi4Ti3O12 solutions for energy storage

(1-x)Sr_0.7Pb_0.15Bi_0.1TiO₃-xBi₄Ti₃O₁₂ ((1-x)SPBT-xBIT, x = 0-0.125) bulk ceramics were developed and calcined via the solid-state method, aimed at the application of pulsed power capacitors. The phase structures, temperature stability, hysteresis loop, and discharge properties were systematically investigated. Considering both the temperature stability and dielectric properties, 0.925SPBT-0.075BIT bulk ceramics with a capacitance variation satisfying the X7R specification were developed for pulsed power capacitors. The energy storage density was 0.252 J/cm³, and the ceramics showed high temperature stability at 80 kV/cm. The discharge current waveforms of the 0.925SPBT-0.075BIT ceramics were recorded. A high discharge power density of approximately 1.01 × 10⁸ W/kg with an 8 Ω load resistor and short discharge period of 84 ns were achieved at 50 kV/cm. The good temperature stability properties and high power density show that the 0.925SPBT-0.075BIT ceramics are well suited for pulsed power capacitors with a wide temperature range.     

Structural dependence of microwave dielectric properties of spinel structured Mg2(Ti1-xSnx)O4 solid solutions: Crystal structure refinement,Raman spectra study and complex chemical bond theory

Mg₂(Ti_1-xSn_x)O₄ (x?=?0–1) ceramics were prepared through conventional solid-state method. This paper focused on the dependence of microwave dielectric properties on crystal structural characteristics via crystal structure refinement, Raman spectra study and complex chemical bond theory. XRD spectrums delineated the phase information of a spinel structure, and structural characteristic of these compositions were achieved with the help of Rietveld refinements. Raman spectrums were used to depict the correlations between vibrational phonon modes and dielectric properties. The variation of permittivity is ascribed to the Mg₂(Ti_1-xSn_x)O₄ average bond covalency. The relationship among the B-site octahedral bond energy, tetrahedral bond energy and temperature coefficient are discussed by defining on the change rate of bond energy and the contribution rate of octahedral bond energy. The quality factor is affected by systematic total lattice energy, and the research of XPS patterns illustrated that oxygen vacancies can be effectively restrained in rich oxygen sintering process. Obviously, the microwave dielectric properties of Mg₂(Ti_1-xSn_x)O₄ compounds were obtained (${\epsilon }_r$= 12.18, $Q\times f$?=?170,130?GHz, ${\tau }_f$?=??53.1?ppm/°C, x?=?0.2).     

A facile pathway to prepare molybdenum boride powder from molybdenum and boron carbide

Molybdenum boride is an ideal hard and wear-resistant material. In this study, a new method is proposed for preparing molybdenum boride, by which Mo first reacts with B₄C to generate the mixture of molybdenum boride and C, and then the product is decarburized by molten Ca to generate CaC₂. Pure molybdenum boride could be obtained after acid leaching to remove the by-product CaC₂. According to the experimental and thermodynamic calculation results, it is concluded that the single-phase MoB could be successfully prepared, while Mo₂B, Mo₂B₅, and MoB₄ could not be synthesized by this method. Moreover, it was found that the particle size of finally prepared MoB is determined by particle size of raw Mo powder. The residual carbon content of the product could be decreased to 0.10 wt% after first reaction at 1673 K for 6 hours and then decarburization reaction at 1673 K for 6 hours.     

Effect of coupling agent content on properties of composites made from polylactic acid and chrysanthemum waste

Chrysanthemum flower is among one of the highly sought after and widely planted flower crops, in particular for cultural and religious ceremonies. However, the chrysanthemum stem and stalk have little value and usually discard as by‐product waste from floristry. The objective of this research is to investigate the potential value of utilizing chrysanthemum stem and stalk as reinforcing fillers for thermoplastic composites. In this study, 2‐mm thick composite sheet containing predefined formulations of polylactic acid (PLA), chrysanthemum waste filler (CWF) ranging from 15 to 60 phr, and maleated polyethylene (MAPE) coupling agent up to 5 phr were prepared with the aid of Haake internal mixer and compression molding. The effect of MAPE loading on tensile, thermal, and morphological properties of PLA/CWF composites was investigated. The findings revealed that PLA/CWF composite attained improved tensile modulus compared to the neat PLA, and the tensile modulus increases with higher concentration of CWF. However, both tensile strength and elongation at break reduces with increase loading of CWF. Overall, PLA/CWF composites with MAPE shows better performance compared to those without MAPE, where an optimum strength of 21.8 MPa can be achieved with 60 phr CW and 3 phr MAPE. The measured tensile strength is comparable to alternatives natural fiber thermoplastic composites demonstrating its potential to be used in non‐structurally demanding application. J. VINYL ADDIT. TECHNOL., 26:10–16, 2020. © 2019 Society of Plastics Engineers