Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Evaluation of microbial toxins,trace elements and sensory properties of a high-theabrownins instant Pu-erh tea produced using Aspergillus tubingensis via submerged fermentation

Theabrownins (TB) are polymeric phenolic compounds associated with the multiple bioactivities of Pu-erh tea, a post-fermented Chinese dark tea. High-TB instant Pu-erh tea was produced via a novel submerged fermentation (SF) using Aspergillus tubingensis and compared with samples produced commercially via the conventional solid-state fermentation (SSF). Viable microorganisms and microbial toxins, especially aflatoxins B₁, G₁, B₂, G₂, cyclopiazonic acid, fumonisins B₁, B₂, B₃ and ochratoxin A, were below the detection limit in all samples. Fewer microbial metabolites were found in SF instant tea compared with the SSF teas. Based on an adult consuming 1 g of instant Pu-erh tea daily, the dietary intake of investigated elements was below the safe limits recommended by various authorities. Tasters viewed the instant tea infusions as very mild, smooth, mellow and full. This suggested that submerged fermentation using A. tubingensis offers a speedy and safe alternative to commercial production of instant Pu-erh tea.     

Fast internal dynamics in polyelectrolyte gels measured by dynamic light scattering

Summary Dynamic light scattering was used to investigate the dynamics of sodium poly(styrene sulfonate) and fully neutralized poly(acrylic acid) gels as a function of the degree of swelling and weight ratio of cross-linking agent. It was shown that the collective diffusion coefficient increases with increasing degree of swelling and that the diffusion coefficient shows stronger concentration dependence than predicted by scaling arguments. For gel samples measured at the swelling equilibrium, the diffusion coefficient increases with increasing gel concentration for both gel systems.     

Kinetic Monte-Carlo simulation of network formation

Summary the simulation described in Part I was applied to random step polyaddition of a trifunctional monomer and the results were compared with exact solution for an infinite system. The gel point conversions, the weight-average degree of polymerization before (P _w) and beyond (P _w,sol) the gel point, the sol fraction and the cycle rank were used for comparison. The best way for detection of the gel point conversion is the extrapolation of the gel fraction, w _g, to w _g=0. The largest fluctuations are exhibited by P _w and P _w,sol. To get results closer to the exact ones, one can repeat several experiments with smaller number of units or increase the number of units, the former way being somewhat more economical. Typical orders of magnitude used were 10⁷ monomeric units.     

Observation of higher order NMR larmor lines by SQUID in solids at low magnetic field

We describe an apparatus allowing the observation of the NMR static longitudinal component of nuclear magnetizationM _z by a SQUID at low magnetic fields and atT=4.2 K in Plexiglas, Teflon, and CaF₂. The higher order NMR Larmor lines at 2f ₀, 3f ₀, and 4f ₀, wheref ₀ is the Larmor frequency of the allowed NMR line, were measured. These lines correspond to a flip of two, three, and four spins, respectively, by one photon. The amplitudes of 2f ₀ and 3f ₀ lines and their field dependences show that the common assertion that the forbidden lines at 2f ₀ and 3f ₀ appear in the same order of perturbation theory and that their intensity decreases with static magnetic fieldB ₀ asB ₀ ^–2 is wrong. In fact, the third Larmor line 3f ₀ appears at higher order than the second Larmor line 2f ₀ and its intensity decreases asB ₀ ^–4 . This is also shown by a theoretical calculation of its intensity. For the first time the NMR SQUID technique allowed the detection of the 4f ₀ line, corresponding to the simultaneous flip of four spins by one photon.     

DC and ac Josephson effects observed in high-temperature superconductor YBaCuO

We report the observation of the dc and ac Josephson effect and quasiparticle tunnelling in the high-temperature superconductor YBaCuO. The observation is made at 4.2 K. These effects were observed in a junction made by a niobium tip pressed against a high-T _c sample of YBaCuO ceramic. We observed a clean dc Josephson effect with a critical currentI _c 2 A and the ac effect with Shapiro steps corresponding toV=(hf/2e)n. The nature of the junction is not clear; however, we suggest that all observed effects can be explained by assuming a singlet pairing state in the ceramic. We have also observed a very peculiar noise behavior along theV-I characteristic.     

Target following with motion prediction for unmanned surface vehicle operating in cluttered environments

The capability of following a moving target in an environment with obstacles is required as a basic and necessary function for realizing an autonomous unmanned surface vehicle (USV). Many target following scenarios involve a follower and target vehicles that may have different maneuvering capabilities. Moreover, the follower vehicle may not have prior information about the intended motion of the target boat. This paper presents a trajectory planning and tracking approach for following a differentially constrained target vehicle operating in an obstacle field. The developed approach includes a novel algorithm for computing a desired pose and surge speed in the vicinity of the target boat, jointly defined as a motion goal, and tightly integrates it with trajectory planning and tracking components of the entire system. The trajectory planner generates a dynamically feasible, collision-free trajectory to allow the USV to safely reach the computed motion goal. Trajectory planning needs to be sufficiently fast and yet produce dynamically feasible and short trajectories due to the moving target. This required speeding up the planning by searching for trajectories through a hybrid, pose-position state space using a multi-resolution control action set. The search in the velocity space is decoupled from the search for a trajectory in the pose space. Therefore, the underlying trajectory tracking controller computes desired surge speed for each segment of the trajectory and ensures that the USV maintains it. We have carried out simulation as well as experimental studies to demonstrate the effectiveness of the developed approach.     

Mechanical properties of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Mechanical properties of isotactic polypropylene/wollastonite/styrene rubber block copolymers (iPP/wollastonite/SRBC) composites were studied as a function of elastomeric poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and SEBS grafted with maleic anhydride (SEBS‐g‐MA) content from 0 to 20 vol%. Microphase morphology was stronger influenced by SRBC elastomers than by different wollastonite types. Higher encapsulation ability of SEBS‐g‐MA than SEBS caused more expressive core‐shell morphology and consequently higher notched impact strength as well as yield parameters, but lower Young's modulus. Higher ductility of the composites with SEBS than with SEBS‐g‐MA has been primarily caused by better miscibility of the polypropylene chains with SEBS molecules. Surface properties of components and adhesion parameters also indicated that adhesion at SEBS‐g‐MA/wollastonite interface, which was stronger than the one at the SEBS/wollastonite interface, influenced higher encapsulation of wollastonite particles by SEBS‐g‐MA. POLYM. ENG. SCI., 47:1873–1880, 2007. © 2007 Society of Plastics Engineers     

Dynamic light scattering measurements on the polystyrene/ethyl acetate system at semi-dilute concentrations as a function of temperature

Summary Measurements of autocorrelation functions extending over a broad time range are reported for a sample of polystyrene in ethyl acetate as a function of temperature between –44°C (-temperature) and 70°C. The corresponding spectra of decay times are obtained by two mathematical methods. The existence of three dynamic processes is shown and their temperature and angular behaviour is studied.