Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Investigation the correlation between chemical structure and swelling,thermal and flocculation properties of carboxymethylcellulose hydrogels

Hydrophilic polymer networks (hydrogels) based on sodium carboxymethylcellulose (NaCMC) and polycarboxylic acids (oxalic, succinic, citric and adipic) as cross-linking agents are synthesized by esterification reaction; one series of NaCMC hydrogels cross-linked with citric acid is prepared with acrylamide and acrylic acid (Aam/Aac) copolymers using the design of semi-interpenetrating polymer networks (semi-IPN), in order to increase their potential application for flocculation purposes. The Infrared spectroscopy (FTIR) of hydrogels confirms the esterification reaction between NaCMC and cross-linking agents. Results of swelling measurements show that citric acid in the amount of 15 wt% gives the hydrogels with the best absorption capacity. The results of Differential scanning calorimetry (DSC) and Thermal gravimetric analysis (TGA) show no significant difference in thermal properties of neat and semi-interpenetrating NaCMC hydrogels. The amorphous nature of hydrogels is confirmed by X-ray diffraction analysis (XRD). The results of flocculation study show that combination of NaCMC network and Aam/Aac copolymer with initial mass ratio of 10/90 creates a theoretical platform for the production of flocculant which could show high efficacy in purifying of water dominated by positively charged particles.     

Development of green extraction process to produce antioxidant-rich extracts from purple coneflower

The present study was conducted to develop subcritical water extraction (SWE) of Echinacea purpurea flowers. The influence of temperature and extraction time on quality of extracts considering total phenols content, total flavonoids content, antioxidant capacity and extraction yield, was determined. Optimized extraction parameters for maximised investigated responses were as follows: 147.56 °C and 8.43 min. The experimental values agreed with the values predicted, thus indicating the adequacy of central composite experimental design for modelling the SWE of bioactive compounds from E. purpurea. Results of the study also highlighted the potential application of E. purpurea subcritical water extracts as a source of valuable bioactive compounds.     

Novel strategy for encapsulation and targeted delivery of poorly water-soluble active substances

Carriers for targeted delivery and controlled release of poorly water-soluble active substances (PWSAS) are facing three challenges: (a) the encapsulation issues, (b) limitations of PWSAS water solubility, and (c) burst drug release which can be pharmacologically dangerous and economically inefficient. The present study brings a novel strategy for encapsulation and controlled release of PWSAS—caffeine in concentrations which are higher than its maximal water solubility without the possibility of burst effect. The modification of hydrophilic carrier based on poly(methacylic acid) was done using casein and liposomes. To further increase the maximal caffeine loading inside the carrier nicotinamide was used. The release study of the encapsulated PWSAS was elaborated with respect to morphology of the carriers and interactions that could be established between its structural components. The carriers swelling and the release of caffeine and nicotinamide were also investigated depending on caffeine concentration, the presence of different liposomal formulations and the volume ratio of liposomal formulation, in three media with different pH simulating the path of the carrier through the human gastrointestinal tract. The synthesized carriers are promising candidates for encapsulation of PWSAS in concentrations which are higher than its maximal water solubility and for the targeted delivery of those dosages.     

Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor

The paper analyses the corrosion behaviour of naturally and artificially aged AA2024 alloy in NaCl solution and in the presence of an environment-friendly corrosion inhibitor, CeCl₃. On the basis of the values of polarisation resistance and corrosion current density, the corrosion resistance of the protective inhibitor film is established as well as the general corrosion resistance of this aluminium alloy. Resistance to pit formation is determined based on the difference in pitting and corrosion potentials while resistance to pit growth is determined based on the amount of charge consumed during pit growth. A scanning electron microscope is used to examine the morphology of the pits formed during the pitting corrosion testing, as well as to determine the cerium content on intermetallic particles and the matrix AA2024 alloy. The corrosion behaviour of AA2024 alloy is investigated after different test periods in NaCl solution and in the same solution with the CeCl₃ inhibitor. The corrosion resistance of both tempers of AA2024 alloy is more than one order of magnitude higher in the presence of CeCl₃. An explanation of the observed differences in the corrosion behaviour of the naturally and artificially aged AA2024 alloy is proposed. Different corrosion behaviour of the alloy after different test periods is also explained.     

Anthocyanin composition of the red wine Babić affected by maceration treatment

Identification of anthocyanins in the wine made of the Croatian autochthonous grape variety of Babić (Vitis vinifera L.) was carried out and their profile was determined by means of high-performance liquid chromatography with diode array and mass spectrometric detection. Dependence of anthocyanins content and profile on maceration treatment conditions was investigated. Statistically significant differences of anthocyanins concentration in wines Babić produced by various maceration treatments were confirmed by the use of multivariate analysis of variances. The investigation results indicated that the maceration temperature exerts higher influence on anthocyanins concentration than the duration of maceration. In addition, on the basis of anthocyanin composition and using different multivariate statistical analyses, differentiation of wines Babić according to maceration treatments was procured.     

The effect of segment length on some properties of thermoplastic poly(ester–siloxane)s

A series of novel thermoplastic elastomers, based on poly(dimethylsiloxane) (PDMS) as the soft segment and poly(butylene terephthalate) (PBT) as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reactions of dimethyl terephthalate and methyl esters of carboxypropyl‐terminated poly(dimethylsiloxane)s (M?_n = 550–2170 g mol^?1) with 1,4‐butanediol. The lengths of both the hard and soft segments were varied while the weight ratio of the hard to soft segments in the reaction mixture was maintained constant (57/43). The molecular structure, composition and molecular weights of the poly(ester–siloxane)s were examined by ¹H NMR spectroscopy. The effectiveness of the incorporation of the methyl‐ester‐terminated poly(dimethylsiloxane)s into the copolymer chains was verified by chloroform extraction. The effect of the segment length on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as the degree of crystallinity and hardness properties of the synthesized TPESs, were studied. Copyright © 2003 Society of Chemical Industry     

An algorithm for architecture partitioning in high-speed networks with bursty traffic

This paper analyzes the performance of a switching architecture. The performance measures include the elapsed time of packet transfer and the waiting time to begin transfer. The architecture is partitioned depending on the type of network used and the expected traffic in the network. Every partition has a switch with a buffer that can absorb surges of bursty traffic within the network partition. The buffer size depends on the type of the network and incoming traffic. The partition size depends on the network bandwidth, network traffic, packet size and buffer size. Examples of different networks are used to show the applications of the model. The results show that the elapsed time of packet switch transfer depends exponentially on the number of partitions in the network.