Propagation and termination of an internal crack in continuously cast austenitic stainless steel analyzed by ∑ values and the Schmid factor

The formation mechanism of an internal crack was clarified from the viewpoint of the crystallography and thermal expansion. An inverse pole figure map obtained by EBSD pattern showed that the crack propagated along the grain boundaries having high ∑ values within the columnar zone. After the crack initiation, these positions were considered to undergo cracking followed by propagation toward the equiaxed side. Near the termination position, the grains ahead of crack propagation had a Schmid factor higher than 0.45 consuming elastic strain energy. Thermal expansion measurements showed that the grain with (0 0 1) orientation had the largest expansion while that with (0 1 1) the smallest. The grain boundaries neighboring the combination of (0 0 1) and (0 1 1) grains had the largest thermal stress. Therefore, thermal stress contributed to the initiation of cracking. It was thus proposed to enlarge the equiaxed zone to prevent cracking by discontinuing the crack propagation.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Possibility of Japanese Cedar Pollen Causing False Positives in the Deep Mycosis Test

Because Japanese cedar pollen (JCP) contains beta-1,3-d-glucan (BG), there is concern that its lingering presence in the atmosphere, especially during its scattering period, may cause false positives in the factor-G-based Limulus amebocyte lysate (LAL) assay used to test for deep mycosis (i.e., G-test). Hence, we examined whether the LAL assay would react positively with substances contained in JCP by using the G-test to measure JCP particles and extracts. BG was purified from the JCP extract on a BG-specific affinity column, and the percentage extractability was measured using three different BG-specific quantitative methods. The G-test detected 0.4 pg BG in a single JCP particle and 10 fg from a single particle in the extract. The percentage extractability of JCP-derived BG was not significantly different among the three quantitative methods. As the JCP particles should technically have been removed during serum separation, they should be less likely to be a direct false-positive factor. However, given that the LAL-assay-positive substances in the JCP extract were not distinguishable by the three BG-specific quantitative methods, we conclude that they may cause the background to rise. Therefore, in Japan false positives arising from JCP contamination should be considered when testing patients for deep mycosis.     

Topic allocation method on edge servers for latency-sensitive notification service

The importance of real-time notification has been growing for social services and Intelligent Transporting System (ITS). As an advanced version of Pub/Sub systems, publish-process-subscribe systems, where published messages are spooled and processed on edge servers, have been proposed to achieve data-driven intelligent notifications. In this paper, we present a system that allows a topic to be managed on multiple edge servers so that messages are processed near the publishers, even when publishers spread over a wide area. Duplicating messages on geographically distributed servers could enable immediate notification to neighboring subscribers. However, the duplicated message spool may cause exhaustion of resources. We prepare a formal model of our publish-process-subscribe system and formulate the topic allocation as an optimization problem under the resource constraints of edge servers. As the optimization problem is NP-hard, we propose heuristics leveraging the locality and the pub/sub relationships observed between clients to use the edge server resources efficiently. Our performance evaluation shows that our method reduces the delay to deliver notifications and the effectiveness of the strategy exploiting the relationships between clients.     

Development of silicon wafer packaging technology for deep UV LED

This paper reports a deep‐ultraviolet LED (deep‐UV‐LED) package based on silicon MEMS process technology (Si‐PKG). The package consists of a cavity formed by silicon crystalline anisotropic etching, through‐silicon vias (TSVs) filled with electroplated Cu, bonding metals made of electroplated Ni/AuSn and a quartz lid for hermetic sealing. A deep‐UV LED die is directly mounted in the Si‐PKG by AuSn eutectic bonding without a submount. It has advantages in terms of size, heat dissipation, light utilization efficiency, productivity and cost over conventional AlN ceramic packages. We confirmed a light output of 30 mW and effective reflection on Si (111) cavity slopes in the Si‐PKG. Based on simulation, further improvement of the optical output is expected by optimizing DUV‐LED die mount condition.     

Investigation on the Interactions between Self-Assembled β-Sheet Peptide Nanofibers and Model Cell Membranes

Self-assembled peptide nanofibers (NFs) obtained from β-sheet peptides conjugated with drugs, including antigenic peptides, have recently attracted significant attention. However, extensive studies on the interactions of β-sheet peptide NFs with model cell membranes have not been reported. In this study, we investigated the interactions between three types of NFs, composed of PEG-peptide conjugates with different ethylene glycol (EG) lengths (6-, 12- and 24-mer), and dipalmitoylphosphatidylcholine (DPPC) Langmuir membranes. When increasing the EG chain length, those interactions significantly decreased considering measurements in the presence of the NFs of: (i) changes in surface pressure of the DPPC Langmuir monolayers and (ii) surface pressure–area (π–A) compression isotherms of DPPC. Because the observed trend was similar to the EG length dependency with regard to cellular association and cytotoxicity of the NFs that was reported previously, the interaction of NFs with phospholipid membranes represented a crucial factor to determine the cellular association and toxicity of the NFs. In contrast to NFs, no changes were observed with varying EG chain length on the interaction of the building block peptide with the DPPC membrane. The results obtained herein can provide a design guideline on the formulation of β-sheet peptide NFs, which may broaden its potential.     

Aqueous One-pot Synthesis of Glycopolymers by Glycosidase-catalyzed Glycomonomer Synthesis Using 4,6-Dimetoxy Triazinyl Glycoside Followed by Radical Polymerization

Glycopolymers have attracted increased attention as functional polymeric materials, and simple methods for synthesizing glycopolymers remain needed. This paper reports the aqueous one-pot and chemoenzymatic synthesis of four types of glycopolymers via two reactions: the β-galactosidase-catalyzed glycomonomer synthesis using 4,6-dimetoxy triazinyl β-D-galactopyranoside and hydroxy group-containing (meth)acrylamide and (meth)acrylate derivatives as the activated glycosyl donor substrate and as the glycomonomer precursors, respectively, followed by radical copolymerization of the resulting glycomonomer and excess glycomonomer precursor without isolating the glycomonomers. The resulting glycopolymers bearing galactose moieties exhibited specific and strong interactions with the lectin peanut agglutinin as glycoclusters.