Hydrogen desorption from alloys Mg–Cu(–KCl): Cu catalysis in detail

Effect of chemical composition of Mg-xCu based alloys (x = 9.94–58.00 wt %) modified by KCl upon their hydrogen storage performance was studied. Kinetic curves and pressure-concentration isotherms were measured in the ranges up to 60 bar and 388 °C, respectively. It was observed that desorption rate dc/dt is not significantly influenced by the composition. Unknown Cu-rich phase was detected that has shown a catalytic effect on desorption from a mixture with other phases. Activation energy of hydrogen desorption decreased with increasing x from 180 kJ/mol down to 98 kJ/mol. Average hydride dissociation enthalpy, ΔH, for the lowest plateau was 75 kJ/mol which is equal to literature value for pure Mg. Slightly lover average value, 67 kJ/mol was obtained for the second plateau and ΔH for the third one decreased from 70 kJ/mol for the lowest to 49 kJ/mol for the highest x.     

Is the association between temperature and mortality modified by age, gender and socio-economic status?

Background

A number of studies have examined the relationship between high ambient temperature and mortality. Recently, concern has arisen about whether this relationship is modified by socio-demographic factors. However, data for this type of study is relatively scarce in subtropical/tropical regions where people are well accustomed to warm temperatures.

Objective

To investigate whether the relationship between daily mean temperature and daily all-cause mortality is modified by age, gender and socio-economic status (SES) in Brisbane, Australia.

Methods

We obtained daily mean temperature and all-cause mortality data for Brisbane, Australia during 1996-2004. A generalised additive model was fitted to assess the percentage increase in all deaths with every one degree increment above the threshold temperature. Different age, gender and SES groups were included in the model as categorical variables and their modification effects were estimated separately.

Results

A total of 53,316 non-external deaths were included during the study period. There was a clear increasing trend in the harmful effect of high temperature on mortality with age. The effect estimate among women was more than 20 times that among men. We did not find an SES effect on the percent increase associated with temperature.

Conclusions

The effects of high temperature on all deaths were modified by age and gender but not by SES in Brisbane, Australia.     

Protease Inhibition—An Established Strategy to Combat Infectious Diseases

Therapeutic agents with novel mechanisms of action are urgently needed to counter the emergence of drug-resistant infections. Several decades of research into proteases of disease agents have revealed enzymes well suited for target-based drug development. Among them are the three recently validated proteolytic targets: proteasomes of the malarial parasite Plasmodium falciparum, aspartyl proteases of P. falciparum (plasmepsins) and the Sars-CoV-2 viral proteases. Despite some unfulfilled expectations over previous decades, the three reviewed targets clearly demonstrate that selective protease inhibitors provide effective therapeutic solutions for the two most impacting infectious diseases nowadays—malaria and COVID-19.     

Synthesis,Characterization and Immunological Evaluation of Self‐Adjuvanting Group A Streptococcal Vaccine Candidates Bearing Various Lipidic Adjuvanting Moieties

Four group A streptococcal glycolipopeptide vaccine candidates with different lipidic adjuvanting moieties were prepared and characterized. The immunogenicity of the compounds was evaluated by macrophage and dendritic cell uptake studies and by in vivo quantification of systemic IgG antibody by ELISA. Three of the candidates showed significant induction of the IgG response.     

Antibacterial modification of nylon-6 nanofibers: structure,properties and antibacterial activity.

Antibacterial nylon 6 (PA6) nanofibers have been prepared in one-step procedure using Nanospider technology. Chlorhexidine (CHX), 1-dodecyltrimethylamonium bromide (DTAB) and benzyltrimethylamonium bromide (BTAB) have been used as antibacterial agents. Samples were characterized by a series of analytical and testing methods to investigate the surface chemistry, zeta potential, structure, morphology, phase composition, mechanical properties and antibacterial activity. Experimental characterization has been combined with molecular modeling to analyze the interaction of nanofibers with modifying molecules for better understanding the effect of nanofibers modification on their properties. Antibacterial modification of PA6 led to significant changes of zeta potential (from -31 mV for PA 6 up to -49 mV for PA6/BTAB), changes in phase composition (decrease of alpha phase content and increase of gamma phase content for PA6/BTAB and PA6/CHX) and to significant increase of fiber diameter for PA6/BTAB. Antibacterial modification resulted in the straightening of nanofibers and to higher permeability of nanofiber textile for all investigated samples. Tensile tests showed the the increase of Young modulus for all the investigated samples. All the modified samples: PA6/DTAB, PA6/BTAB and PA6/CHX exhibit good antibacterial activity.     

Detection of light-absorbing iron oxide particles using a modified single-particle soot photometer

Copyright © 2016 American Association for Aerosol Research     

Off-line coupling of capillary electrophoresis to substrate-assisted laser desorption inductively coupled plasma mass spectrometry

A novel off-line coupling of capillary electrophoresis (CE) and inductively coupled plasma mass spectrometry (ICPMS) is reported here. The coupling interface is based on the connection of a separation capillary to a deposition capillary via a liquid junction maintaining high separation efficiency and sample utilization due to the self-focusing effect and lack of pressure-induced flow in comparison with nebulizer-like interfaces. The separation is recorded in the form of droplets of CE effluent on a suitable substrate--a poly(ethylene terephthalate) glycol (PETG) sample plate placed inside a partially evacuated chamber. Substrate-assisted laser desorption (SALD) is used to vaporize the sample fractions and to enable further transfer to the ICPMS. The mechanism of SALD is examined using model samples deposited on a variety of substrates. The highest response is obtained for a PETG substrate; sample desorption due to ablation of PETG is found to outweigh direct ablation of sample. Detection limits are given for several metal elements. Finally, a rapid (2.5-min), high-resolution separation of Cr(III)/Cr(VI) species injected in subpicomolar quantity is shown.     

Dry versus hydrated collagen scaffolds: are dry states representative of hydrated states?

Collagen composite scaffolds have been used for a number of studies in tissue engineering. The hydration of such highly porous and hydrophilic structures may influence mechanical behaviour and porosity due to swelling. The differences in physical properties following hydration would represent a significant limiting factor for the seeding, growth and differentiation of cells in vitro and the overall applicability of such hydrophilic materials in vivo. Scaffolds based on collagen matrix, poly(DL-lactide) nanofibers, calcium phosphate particles and sodium hyaluronate with 8 different material compositions were characterised in the dry and hydrated states using X-ray microcomputed tomography, compression tests, hydraulic permeability measurement, degradation tests and infrared spectrometry. Hydration, simulating the conditions of cell seeding and cultivation up to 48?h and 576?h, was found to exert a minor effect on the morphological parameters and permeability. Conversely, hydration had a major statistically significant effect on the mechanical behaviour of all the tested scaffolds. The elastic modulus and compressive strength of all the scaffolds decreased by ~95%. The quantitative results provided confirm the importance of analysing scaffolds in the hydrated rather than the dry state since the former more precisely simulates the real environment for which such materials are designed.

Open image in new window

     

The properties of free-standing epoxy polymer multi-mode optical waveguides

The paper reports on the fabrication and characterisation of free-standing multimode optical epoxy polymer waveguides consisting of a core made of EpoCore and EpoClad polymer cladding and cover protection layers. The 50 × 50 μm² rectangular waveguides are intended for short-reach optical interconnection and optimised for an operating wavelength of 850 nm. The waveguides of the proposed shapes were fabricated by a standard photolithography process on a silicon substrate provided with a Poly(vinyl alcohol) thin layer. The free-standing structure was then achieved by peeling the deposited EpoClad/EpoCore/EpoClad structures of that substrate. The optical scattering losses of the created planar waveguides, measured by the fibre probe technique at 632.8 and 964 nm, were 0.30 dB cm⁻¹ at 632.8 nm and 0.17 dB cm⁻¹ at 964 nm. Propagation optical loss measurements for rectangular waveguides were performed by the cut-back method and the best samples had optical losses below 0.55 dB cm⁻¹ at 850 and 1310 nm.