碳纤维表面处理对铝电解用硼化钛阴极涂层性能的影响

硼化钛阴极涂层是铝电解用可润湿性阴极材料中的一种，具有优良的抗钠渗透性和对铝液润湿性，可以有效地延长铝电解槽寿命。碳纤维是硼化钛涂层材料的增强剂之一．对硼化钛阴极涂层的性能影响很大。本文研究了不同工艺的液相碳纤维表面氧化处理法对硼化钛阴极涂层抗拉强度和粘接强度的影响。采用PTIR检测碳纤维处理后表面含氧基团的变化，寻找影响硼化钛阴极涂层性能的原因，从而达到最有效地提高TiB2阴极涂层抗拉强度和粘接强度的目的。结果表明，采用工艺(1)(10％HNO3，80℃、恒温5min．超声波、5min)对碳纤维进行表面处理最合理，处理后碳纤维表面含氧基团的含量最高．用其制备硼化钛阴极涂层的抗拉强度、粘接强度最大。     

Effect of electrolysis superheat degree on anticorrosion performance of 5 Cu/（10NiO-NiFe2O4） cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.     

铝电解用TiB_2阴极涂层固化、炭化的升温制度

采用DTG ,DDTA等热分析手段 ,研究了高温固化、炭化过程中 ,铝电解用TiB2 阴极涂层糊料的质量和能量的变化速率 ,制定了涂层的变速固化、炭化升温制度 ;在此基础上 ,研究了升温制度对TiB2 阴极涂层性能的影响。结果表明 :变速升温制度优于匀速升温制度 ,采用变速固化、炭化升温制度所制备的涂层形变小、无裂纹 ,其抗拉强度达 3.13MPa,电阻率为 2 3.2 μΩ·m ;而采用升温速度为 10 .3℃ /h的匀速固化、炭化升温制度制备的涂层形变大、裂纹多 ,抗拉强度小 (2 .6 9MPa) ,电阻率大 (2 8.6 μΩ·m)。     

沥青调制温度对活性炭材料结构及电容特性的影响

以煤焦油沥青为原料，在不同温度下调制得到碳质微晶结构的中间相沥青，采用化学活化法制得超级电容器用高比表面积活性炭。以制备的活性炭作电极材料组装模拟电容器，6mol／LKOH溶液为电解液，考察了中间相沥青的调制温度对活性炭结构和电容行为的影响。结果表明：随着调制温度的提高，活性炭比表面积先增加后减小，在450℃时达到最大值，为3250m^2／g；制备的活性炭孔径主要集中在14nin范围内：在350℃时，无定形结构的中间相沥青有利于扩孔，制得的活性炭具有较高的中孔含量：随着调制温度的继续提高，中孔含量下降：活性炭比电容量随着调制温度的提高先增大后减小，450℃时达到最大值，为215F／g。     

Ambient temperature cured TiB_2 cathode coating for aluminum electrolysis

1　INTRODUCTIONAluminumindustryhasbeendevelopingrapidlyinChinainrecentyears ,soderbergcellshavebeenre placedwithmodernprebakecellsinmanyaluminumsmelters,theaveragecelllifehowever ,forprebakecellsinourcountrywasonlyabout130 0d ,muchlowerthantheaveragecelllife ,i.e .above 2 5 0 0d ,forthecellsindevelopedcountries .TiB2 cathodecoating (TCC)couldbeoneofthesolutionstoreducegreatlytheopportunitytotheearlyfailureofcellsandextendthecelllifeofprebakecell[14 ] .Theconceptoftitaniumdiboride (TiB2 …     

X(K或Li)3AlF6-Al2O3体系低温电解研究现状评述

详细概述氧化铝在锂冰晶石和钾冰晶石体系中的低温电解研究现状,系统分析各体系的优缺点,指出将来的研究方向不应该局限于单一冰晶石体系,而应该是多种冰晶石组成的复合体系,充分发挥各自优势,减少或消除弊端,最终寻找出一种低温、高氧化铝溶解度、高电导率和低铝溶解损失的新型电解质。     

Preparation and electrochemical characterization of activated carbons by chemical-physical activation

A process was proposed based on the combination of chemical and physical activation for the production of activated carbons used as the electrode material for electric double layer capacitor (EDLC). By material characterization and electrochemical methods, the influences of the activitation process on the specific surface area, pore structure and electrochemical properties of the activated carbons were investigated. The results show that specific surface area, the mesopore volume, and the specific capacitance increase with the increase of the mass ratio of KOH to char (m(KOH)/m(char)) and the activation time, respectively. When m(KOH)/m(char) is 4.0, the specific surface area and the mesopore volume reach the maximum values, i.e. 1 960 m²/g and 0.308 4 cm³/g, and the specific capacitance is 120.7 F/g synchronously. Compared with the chemical activation, the activated carbons prepared by chemical-physical activation show a larger mesopore volume, a higher ratio of mesopore and a larger specific capacitance. Foundation item: Project(2007BAE12B01) supported by the National Key Technology Research and Development Program of China     

铝电解用NiFe2O4-Cu金属陶瓷阳极的初步研究

采用粉末冶金技术制备了NiFe2O4-Cu金属陶瓷惰性阳极,并对其导电性能和腐蚀行为进行了初步研究.研究发现,金属Cu与NiFe2O4陶瓷润湿性差,难以实现致密化,在升温过程中,过低的表观密度能导致金属铜氧化,降低导电性能.在电解过程中,金属铜的耐蚀性好,但存在聚结现象,可能会导致电流分布不均匀,同时陶瓷基体发生非协同溶解.     

300 kA铝电解槽中焦粒焙烧过程温度场的仿真优化

使用有限元法建立了300 kA铝电解槽的焦粒焙烧三维1/4整槽模型,针对目前普遍采用焦粒均匀铺设方式,对其焦粒焙烧过程的温度分布与变化特征进行了瞬态数值仿真研究。当前的焦粒焙烧启动方式存在阴极表面温差过大、各阴极炭块随空间位置不同温度分布差异过大、端部第1至第3块阴极炭块平均温度低于900℃、阴极炭块和捣固糊升温速度过快等缺陷。提出在阴极表面从电解槽边缘向中心依次铺设电阻率递增的焦粒层的优化焙烧方案,并进行温度场仿真计算。结果表明：该优化方案可以使阴极表面温度分布更加均匀,端部第1至第3块阴极炭块表面温差比优化前降低8%以上,中间第4至第13块阴极炭块表面温差降低30%以上,阴极炭块和阴极缝糊平均升温速度降低12%,该优化方案更有利于减少电解槽的早期破损。     

导流槽阴极导杆安装方式对阴极表面电流分布的影响

将某厂现有的160kA Hall—Heroult铝电解槽改造成导流槽后，在阴极上表面和阳极底面呈斜坡状的条件下，计算了采用不同阴极导杆安装方式时阴极的电位和电流分布，即通过建立导流槽内部从阳极到阴极的一个半切片电热场模型，用有限元法分别对水平和平行于阴极斜坡两种不同导流槽阴极导杆的安装方式下阴极电位和表面电流密度分布进行了计算。结果表明，不同的阴极导杆安装方法对导流槽阴极的总电位降大小没有明显影响，但是水平阴极导杆安装更有利于阴极表面电流密度的均匀分布。