Efficient QoS support in a slotted multihop WDM metro ring

A novel distributed access protocol for a slotted wavelength-division-multiplexing (WDM) metro ring employing all-optical packet switching and supporting quality-of-service (QoS) classes is presented and analyzed. Since we assume that there are more nodes than available wavelengths in the network, we obtain a scalable multihop WDM ring as underlying network architecture. By dividing each channel into several time slots and further applying destination release and slot reuse, data packets can be efficiently transmitted and received in a statistically multiplexed manner. In our architecture, each node is equipped with one tunable transmitter and one fixed-tuned receiver. Furthermore, as we generally consider so-called a posteriori access strategies, different packet selection schemes are proposed and compared. An analytical model based on the semi-Markov process methodology is developed to quantify the performance of one of these schemes. As a key element of the protocol, an efficient QoS support access mechanism is proposed and its performance is evaluated. The new QoS control scheme adopts a frame-based slot reservation strategy including connection setup and termination, which only slightly increases the signaling and node processing overhead. Thus, an efficient hybrid protocol combining connectionless and connection-oriented packet transmissions is proposed     

Surface modification of polyester and polyamide fabrics by low frequency plasma polymerization of acrylic acid

In this study, the surface characteristics of polyester and polyamide fabrics were changed by plasma polymerization technique utilizing acrylic acid as precursor. This monomer was used to produce hydrophilic materials with extended absorbency. The hydrophilicity, total wrinkle recovery angle (WRA°) and breaking strength of the fabrics were determined prior and after plasma polymerization treatment. The modification of surfaces was carried out at low pressure (<100 Pa) and low temperature (<50°C) plasma conditions. The effects of exposure time and discharge power parameters were optimized by comparing properties of the fabrics before and after plasma polymerization treatments. It was shown that two sides of polyester fabric samples were treated equally and homogeneously in plasma reactor. For polyester fabrics, the minimum wetting time, 0.5 s, was observed at two plasma processing parameters of 10 W–45 min and 10 W–20 min, where untreated fabric has a wetting time of 6 s. For polyester fabrics, the maximum value was obtained at 60 W–5 min with the wrinkle recovery angle of 306° where the untreated fabric has 290°. The optimum plasma conditions for polyamide fabrics were determined as 30 W–45 min where 2 s wetting time was observed. Wrinkle recovery angle of untreated polyamide fabric was 264°. In this study, after plasma polymerization of acrylic acid, wrinkle recovery angle values were increased by 13%. No significant change was observed in breaking strength of both fabrics after plasma treatment. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2318–2322, 2007     

Episodic memory and metamemory in Parkinson’s disease patients.

This study investigated episodic memory and metamemory for verbs and nouns in patients who have cognitive impairments associated with Parkinson’s disease (PD). PD patients and healthy control participants were asked to recall word pairs and provide feeling-of-knowing (FOK) judgments for the items they were unable to recall. This was followed by a 4-alternative recognition test. PD patients were impaired in both recall and recognition, compared with controls. In terms of metamemory, PD patients were less confident in their ability to recognize the unrecalled items in a future recognition test. Most important, accuracy of PD patients’ FOK judgments was not above chance and was lower than that of control participants. The PD group correctly recognized fewer verbs than nouns, but type of material (verb vs. noun) had no impact on recall or FOK judgments. In addition, contribution of executive functions to FOK accuracy was different in PD patients and controls. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Methanol tolerant electrocatalysts for the oxygen reduction reaction

Direct methanol fuel cells (DMFCs) represent an interesting alternative in obtaining electricity in a clean and efficient way. Portable power sources are one of the most promising applications of passive DMFCs. One of the requirements in these devices is to use high alcohol concentration, which due to methanol crossover causes a considerable loss of fuel cell efficiency. In order to develop methanol tolerant cathodes with suitable activity, different supported catalysts namely PtCo/C and PtCoRu/C, were prepared either via ethylene glycol reduction (EG) with or without microwave heating assistance (MW) or via the alloy method, the latter followed by a thermal treatment in a reducing atmosphere (N₂/H₂). All cathode-catalysts were tested to determine the role of the components in simultaneously enhancing the oxygen reduction reaction (ORR) and discouraging the methanol oxidation reaction. According to the synthesis methodology, X-ray photoelectron spectra showed that the amount of metal oxides on the surface varies, being higher on the PtCo/C EG and PtCoRu/C EG catalysts. The electrochemical characterization of the catalysts was accomplished in a three electrodes electrochemical cell with a glassy carbon rotating disk electrode covered with a thin catalytic film as working electrode. To study the ORR and the influence of different methanol concentrations, linear sweep voltammetry and cyclic voltammetry were employed. The PtCo/C EG, with an important metal oxide amount on the surface, and the PtCoRu/C MW and EG electrodes, both with RuO₂ on their surfaces, were the most tolerant to methanol presence.     

Internet traffic engineering

The main goal of Internet traffic engineering is to efficiently optimize the performance of operational networks in order to avoid the well-known shortcomings of the typical destination-based IP routing. Traffic engineering attempts to reduce or even avoid congestion hot spots and to improve resource utilization across the backbone IP network. During the last years traffic engineering has become an inevitable tool concerning performance optimization in large Internet backbones. The core objective of this paper is to give an overview of the architectures and mechanisms for traffic engineering.     

Aloe vera-based antibacterial porous sponges for wound dressing applications

Journal of Porous Materials - The antibacterial sponges with high macroporosity, high interconnectivity and high biocompatibility is a significant concern for wound healing applications. In this...     

Primary User Emulation Detection Algorithm Based on Distributed Sensor Networks

In this paper, we propose a novel primary user emulation (PUE) detection approach which employs a distributed sensor network, where each sensor node operates as an independent PUE detector. Distributed nodes collaborate in order to obtain the final detection results for the whole network. A voting algorithm is used to improve the performance of energy detection, while the classification is conducted by the nearest node in order to improve the efficiency of the detector. As a result of voting, if a potential primary user exists, then the features of the unknown user is compared with entries from the database in order to obtain a solid detection match. An artificial neural network (ANN) is used for the classification of an unknown user. To assess the accuracy of the detection result, we implement a reliability check at the output of ANN. The proposed algorithm is validated via computer simulations as well as by experimental hardware implementations using the Universal Software Radio Peripheral (USRP) software-defined radio (SDR) platform. The experiment results show that the distributed network detector detects the PUE 180–200%, depending on the number of primary users, faster than single node detector.     

X-ray investigation of sintered cadmium doped hydroxyapatites

Pure and cadmium (Cd) doped hydroxyapatites (HA, Ca₁₀(PO₄)₆(OH)₂) were synthesized by a precipitation method from aqueous solutions of Ca(NO₃)₂4·H₂O for the former and Cd(NO₃)₂4·H₂O for the latter, by using (NH₄)₂HPO₄ as the phosphate source, while pH was kept in the range of 11–12. The effect of incorporation of Cd²⁺ ions into the structure of HA was investigated after the air sintering at 1100 °C for 1 h. The results indicate that Cd²⁺ addition into HA yields nearly fully densified products with respect to pure stoichiometric HA. The XRD patterns showed that Cd doping increases the crystallinity of HA. The 2, 4.4, and 8.8 mol% Cd doped HAs had calcium oxide (CaO) impurity phase in their lattice. The CaO phase in the HA structure gradually disappeared with increasing Cd amount, and was replaced with cadmium oxide (CdO) in the CdHA doped with 11 mol% Cd. Cd²⁺ ion incorporation decreased the a- and c-axis lattice constants and unit cell volume of HA.     

Development of flame retardancy properties of new halogen‐free phosphorous doped SiO2 thin films on fabrics

In this study, flame retardancy properties of fabrics treated with phosphorous (P) doped and undoped SiO₂ thin films were developed by sol–gel technique. As to this aim, P‐doped and undoped SiO₂ film were coated on cotton fabric from the solutions prepared from P, Si‐based precursors, solvent, and chelating agent at low temperature in air using sol–gel technique. To determine solution characteristics, which affect thin film structure, turbidity, pH values, and rheological properties of the prepared solutions were measured using a turbidimeter, a pH meter, and a rheometer machines before coating process. The thermal, structural, and microstructural characterization of the coating were done using differential thermal analysis/thermograviometry, fourier transform infrared spectroscopy, X‐ray diffractometry, and scanning electron microscopy. In addition, tensile strength, wash fastness, flame retandancy, and lightness properties of the coated fabrics were determined. To compensate the slight loss of tensile strength of samples, which occurred at the treated fabrics with P‐doped Si‐based solutions, the cotton fabrics were coated with polyurethane films during second step. In conclusion, the flame retardant cotton fabric with durability of washing as halogen‐free without requiring after treatment with formaldehyde was fabricated using sol–gel processing for the first time. Moreover the cotton fabrics, which were treated with P‐doped Si‐based solutions and then coated with polyurethane at second step, still has got nonflammable property. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Surface modification of textiles by glow discharge technique: Part II: Low frequency plasma treatment of wool fabrics with acrylic acid

In this study, wool fibers are modified by low frequency plasma polymerization of acrylic acid regarding to its' hydrophobic character due to cuticular cells at their surfaces. Variables of the plasma glow discharge processes were power (40–100 W) and exposure time (5–45 min). The effect of plasma modification in the performance properties of wool were investigated on the basis of hydrophilicity of wool, average wrinkle recovery angle, and breaking strength. The surface chemical structures of fabrics were examined with x‐ray photoelectron spectroscopy. The hydrophobic wool fabric became hydrophilic after all plasma treatments except one (40W–5 min). Average wrinkle recovery angle of the treated fabrics were between 157 and 178°, while that of untreated fabric was 180°. The treated fabrics had a little bit lower angles according to the untreated fabric. However, even the lowest value as 157° means that the fabric has a good crease resistance property. The breaking strengths of fabrics were increased up to 26% after the plasma treatments. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010