Effects of Preprocessing on Multi-Direction Properties of Aluminum Alloy Cold-Spray Deposits

The effects of powder preprocessing (degassing at 400 °C for 6 h) on microstructure and mechanical properties of 5056 aluminum deposits produced by high-pressure cold spray were investigated. To investigate directionality of the mechanical properties, microtensile coupons were excised from different directions of the deposit, i.e., longitudinal, short transverse, long transverse, and diagonal and then tested. The results were compared to properties of wrought 5056 and the coating deposited with as-received 5056 Al powder and correlated with the observed microstructures. Preprocessing softened the particles and eliminated the pores within them, resulting in more extensive and uniform deformation upon impact with the substrate and with underlying deposited material. Microstructural characterization and finite element simulation indicated that upon particle impact, the peripheral regions experienced more extensive deformation and higher temperatures than the central contact zone. This led to more recrystallization and stronger bonding at peripheral regions relative to the contact zone area and yielded superior properties in the longitudinal direction compared with the short transverse direction. Fractography revealed that crack propagation takes place along the particle-particle interfaces in the transverse directions (caused by insufficient bonding and recrystallization), whereas through the deposited particles, fracture is dominant in the longitudinal direction.     

Review of Bioretention System Research and Design: Past, Present, and Future

This paper reviews the evolution of bioretention systems, a promising at-source storm-water best management practice. The introduction of bioretention systems in the 1990s by Prince George’s County, Md. is examined along with the motivations behind the development of the systems. A summary of the research findings on the performance of bioretention systems is provided including proposed design modifications to improve the field performance. Also included is an overview of past and current bioretention design guidelines in North America, as well as a discussion of issues surrounding the public adoption and implementation of bioretention systems. Potential alternative uses for the systems are highlighted and a review of bioretention modeling work is provided. Finally, the paper outlines research needs and anticipated future work necessary to bring about the widespread use of bioretention systems.     

Management factors associated with bovine respiratory disease in preweaned calves on California dairies: The BRD 100 study

The objective of this cross-sectional study was to determine how management practices on California dairies may be associated with bovine respiratory disease (BRD) in preweaned calves. A convenience sample of 100 dairies throughout California, providing a study population of 4,636 calves, were visited between May 2014 and April 2016. During each farm visit, in-person interviews with the herd manager or calf caretaker were conducted to collect information about herd demographics, maternity pen, colostrum and calf management, herd vaccinations, and dust abatement. A random sample of preweaned calves was identified and evaluated for the presence of BRD using a standardized tool. A survey-adjusted generalized linear mixed model with a logit link function was fitted with calf as the unit of analysis and dairy as the random effect. Mean study herd size (±SE) was 1,718 (±189.9) cows. Survey-adjusted estimates of breed types in the sample were 81.6% (±0.6) Holstein, 13.1% (±0.4) Jersey, and 5.3% (±0.5) crossbred or other purebred breeds, and calf sex proportions were 73.8% (±1.0) female and 26.2% (±1.0) male. Overall survey-adjusted BRD prevalence in the study herds was 6.91% (±0.69). Housing factors positively associated with BRD were metal hutches compared with wood hutches [odds ratio (OR) = 11.19; 95% confidence interval (CI) = 2.80–44.78], calf-to-calf contact in calves >75 d of age (OR = 9.95, 95% CI = 1.50–65.86), feeding Holstein calves <2.84 L of milk or replacer per day (OR = 7.16, 95% CI = 1.23–41.68), and lagoon water used for flushing manure under hutches compared with no flush (OR = 12.06, 95% CI = 1.93–75.47). Providing extra shade over hutches (OR = 0.08; 95% CI = 0.02–0.37), feeding calves at least 90% saleable milk (OR = 0.27, 95% CI = 0.13–0.54) or pasteurized milk (OR = 0.10; 95% CI = 0.03–0.36), and feeding >5.68 L of milk or replacer per day to Jersey calves (OR = 0.04; 95% CI = 0.01–0.28) were negatively associated with BRD. Our study identified management practices on California dairies with variability and that may contribute to differences in BRD prevalence, which will be incorporated into a risk-assessment tool to control and prevent BRD in preweaned dairy calves.     

Study of oxidation after monoacrylate grafting on polyethylene

BACKGROUND: The surface properties of high‐density polyethylene and linear low‐density polyethylene were modified by grafting urethane monoacrylate monomer under UV irradiation. This graft polymerization was carried out on native substrates and on substrates pre‐treated by wet oxidation, for different oxidation times. RESULTS: As the urethane monacrylate layer is crosslinked, its grafting efficiency was checked by dissolving the polyethylene substrates in hot toluene. Grafting was evidenced by Fourier transform infrared spectroscopy of the obtained residues, which showed that both the characteristic urethane acrylate (3350 cm^?1) and polyethylene (2920, 730 and 720 cm^?1) bands were observable for any polyethylene oxidation time. For an oxidation time longer than 10 hours, acrylate grafting was homogeneous and the grafted surface was smooth with a roughness of less than 10 nm. In addition, X‐ray photoelectron spectroscopy analysis of the residues revealed that O/C had an average value of 0.19, which is lower than the value corresponding to pure acrylate (0.42), whereas N/C had an average value of 0.068, also lower than that of pure acrylate (0.09), thus confirming the grafting. CONCLUSION: A urethane monoacrylate layer was grafted on native and oxidized polyethylene films. For highly oxidized films, the grafted surfaces are smooth and homogeneous. Copyright © 2008 Society of Chemical Industry     

Improved Peanut Flour for a Reduced-Fat Peanut Butter Product

A commercial peanut flour (12% fat) was mixed with water (30% w/w), homogenized and drum‐dried in a double drum dryer. The drum clearance was adjusted to result in thin dried sheets which on milling resulted in a very fine, single banded particle size flour. The flour was no longer gritty and was used to dilute fat by mixing with full fat (52.5%) paste to obtain a 30% fat reduction in the peanut butter product. Response surface methodology, RSM, was used to optimize drum temperature (T), speed (S), and clearance (C) in order to minimize stickiness and hardness, maximizing oil separation and particle size. Based on surface responses and contour plots, optimum conditions were: T = 135 °C, S = 1 rpm and C = 0.33 mm. Optimum values predicted by RSM for peanut flour particle size, peanut butter stickiness, hardness, and oil separation were: 49.65 μm, 12347 N, 311.4 N and 6.87% respectively. Close agreement between experimental and predicted values was obtained.     

Analysis and validation of a real-time AC drive simulator

This paper presents the analysis and validation of a real-time AC drive simulator. Real-time simulation has been used for over a decade in power systems engineering to test controllers thoroughly, efficiently, and safely. The development and testing of large DC drives could benefit from this type of simulation, but real-time power system simulators have modeling restrictions preventing stable and accurate simulation of isolated drives switching at high frequencies. These restrictions can be overcome by combining in a single model both the power converter and motor models. After discussing the salient issues related to the real-time simulation of DC drives, a prototype real-time simulator for drives is described. Its ability to accurately emulate the behavior of large drives is demonstrated through two case studies. A first case study demonstrates the feasibility of simulating a drive of typical complexity in real-time. The second case study demonstrates how the controller for a PWM VSI fed induction motor, switching at 4 kHz, is designed, implemented in a microcontroller and tested in real-time using a simulated inverter, motor and load. Comparisons against results obtained with another simulation tool, which uses extremely accurate variable-step integration algorithms, demonstrates the validity of our approach.