A thermal perspective of flash sintering: The effect of AC current ramp rate on microstructure evolution

In flash sintering experiments, the thermal history of the sample is key to understanding the mechanisms underlying densification rate and final properties. By combining robust temperature measurements with current-ramp-rate control, this study examined the effects of the thermal profile on the flash sintering of yttria-stabilized zirconia, with experiments ranging from a few seconds to several hours. The final density was maximized at slower heating rates, although processes slower than a certain threshold led to grain growth. The amount of grain growth observed was comparable to a similar conventional thermal process. The bulk electrical conductivity correlated with the maximum temperature and cooling rate. The only property that exhibited behavior that could not be attributed to solely the thermal profile was the grain boundary conductivity, which was consistently higher than conventional in flash sintered samples. These results suggest that, during flash sintering, athermal electric field effects are relegated to the grain boundary.     

High-temperature stabilization of polypropylene using hindered phenol–thioester stabilizer combinations,Part 1: Optimization and efficacy via nondust blends

The thermal degradation of unstabilized polypropylene has been investigated under long-term processing (twin extruder) and thermal aging at 150°C, with additive concentration studies on combinations of an established hindered phenolic antioxidant (pentaerythritol tetrakis (3-(3,5-di-tert-butyl-4-hydroxyphenyl) propionate) [S1010] and two popular thioesters (distearyl-3,3′-thiodipropionate [DSTDP] and didodecyl-3,3′-thiodipropionate [DLTDP]) using melt flow rate, carbonyl index and powder diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) (FTIR), and differential scanning calorimetry (DSC) (oxidation induction time [OIT]) and ultimate embrittlement time (Fracture) on injection-molded test pieces. It was found that 20:80 phenol:thioester ratios provided the best long-term thermal stability (LTTS); however, this was the reverse for processing stabilization (80:20), underlining the antioxidant nature of the two stabilizers (long term vs. melt). Melt preblending of the stabilizers (to form a no-dust blend) gave rise to improved LTTS. DRIFTS FTIR indicated that there was an improvement in preblending the additives, which removed any volatile impurities. Increased additive dispersion and localized potential efficacy in the stabilization cycle is important, as well as possible improved addition of the additives to the extruder rather than fine powder. The data are discussed in relation to the long-term stabilization of polypropylene in high-temperature applications such as under the bonnet of automobiles where minimizing stabilizer losses and maximizing synergy are important.     

Fire safe,sustainable loose furnishing

The aim of this exploratory study has been to investigate the fire properties and environmental aspects of different upholstery material combinations, mainly for domestic applications. An analysis of the sustainability and circularity of selected textiles, along with lifecycle assessment, is used to qualitatively evaluate materials from an environmental perspective. The cone calorimeter was the primary tool used to screen 20 different material combinations from a fire performance perspective. It was found that textile covers of conventional fibres such as wool, cotton and polyester, can be improved by blending them with fire resistant speciality fibres. A new three‐dimensional web structure has been examined as an alternative padding material, showing preliminary promising fire properties with regard to ignition time, heat release rates and smoke production.     

Interlaced layer thicknesses within single laser powder bed fusion geometries

The geometrical design freedoms associated with additive manufacturing techniques are currently well exploited and finding commercial application. The capability of layer-based processes to allow modification of composition and microstructure in process to achieve functional grading is currently a growing topic. In this work, a method is demonstrated for varying layer thickness within single components that allows part sections to be interlaced for the purpose of locally manipulating material and structural properties. Demonstrator geometries are explored here which exhibit the interfaces within specimens constituted of both 30 µm and 150 µm. Accordingly, a new design freedom for laser powder bed fusion is created.     

Occupational exposure and health risks of volatile organic compounds of hotel housekeepers: Field measurements of exposure and health risks

Hotel housekeepers represent a large, low-income, predominantly minority, and high-risk workforce. Little is known about their exposure to chemicals, including volatile organic compounds (VOCs). This study evaluates VOC exposures of housekeepers, sources and factors affecting VOC levels, and provides preliminary estimates of VOC-related health risks. We utilized indoor and personal sampling at two hotels, assessed ventilation, and characterized the VOC composition of cleaning agents. Personal sampling of hotel staff showed a total target VOC concentration of 57 ± 36 µg/m³ (mean ± SD), about twice that of indoor samples. VOCs of greatest health significance included chloroform and formaldehyde. Several workers had exposure to alkanes that could cause non-cancer effects. VOC levels were negatively correlated with estimated air change rates. The composition and concentrations of the tested products and air samples helped identify possible emission sources, which included building sources (for formaldehyde), disinfection by-products in the laundry room, and cleaning products. VOC levels and the derived health risks in this study were at the lower range found in the US buildings. The excess lifetime cancer risk (average of 4.1 × 10⁻⁵) still indicates a need to lower exposure by reducing or removing toxic constituents, especially formaldehyde, or by increasing ventilation rates.     

Nanogrooved carbon microtubes for wet three‐dimensional printing of conductive composite structures

Recent advances in three‐dimensional (3D) printing have enabled the fabrication of interesting structures which are not achievable using traditional fabrication approaches. The 3D printing of carbon microtube composite inks allows fabrication of conductive structures for practical applications in soft robotics and tissue engineering. However, it is challenging to achieve 3D printed structures from solution‐based composite inks, which requires an additional process to solidify the ink. Here, we introduce a wet 3D printing technique which uses a coagulation bath to fabricate carbon microtube composite structures. We show that through a facile nanogrooving approach which introduces cavitation and channels on carbon microtubes, enhanced interfacial interactions with a chitosan polymer matrix are achieved. Consequently, the mechanical properties of the 3D printed composites improve when nanogrooved carbon microtubes are used, compared to untreated microtubes. We show that by carefully controlling the coagulation bath, extrusion pressure, printing distance and printed line distance, we can 3D print composite lattices which are composed of well‐defined and separated printed lines. The conductive composite 3D structures with highly customised design presented in this work provide a suitable platform for applications ranging from soft robotics to smart tissue engineering scaffolds. © 2019 Society of Chemical Industry     

Modification of narrow‐spectrum peptidomimetic polyurethanes with fatty acid chains confers broad‐spectrum antibacterial activity

Each year, thousands of patients die from antimicrobial‐resistant bacterial infections that fail to respond to conventional antibiotic treatment. Antimicrobial polymers are a promising new method of combating antibiotic‐resistant bacterial infections. We have previously reported the synthesis of a series of narrow‐spectrum peptidomimetic antimicrobial polyurethanes that are effective against Gram‐negative bacteria, such as Escherichia coli; however, these polymers are not effective against Gram‐positive bacteria, such as Staphylococcus aureus. With the aim of understanding the correlation between chemical structure and antibacterial activity, we have subsequently developed three structural variants of these antimicrobial polyurethanes using post‐polymerization modification with decanoic acid and oleic acid. Our results show that such modifications converted the narrow‐spectrum antibacterial activity of these polymers into broad‐spectrum activity against Gram‐positive species such as S. aureus, however, also increasing their toxicity to mammalian cells. Mechanistic studies of bacterial membrane disruption illustrate the differences in antibacterial action between the various polymers. The results demonstrate the challenge of balancing antimicrobial activity and mammalian cell compatibility in the design of antimicrobial polymer compositions. © 2019 Society of Chemical Industry     

Bayesian Inference for ARFIMA Models

This article develops practical methods for Bayesian inference in the autoregressive fractionally integrated moving average (ARFIMA) model using the exact likelihood function, any proper prior distribution, and time series that may have thousands of observations. These methods utilize sequentially adaptive Bayesian learning, a sequential Monte Carlo algorithm that can exploit massively parallel desktop computing with graphics processing units (GPUs). The article identifies and solves several problems in the computation of the likelihood function that apparently have not been addressed in the literature. Four applications illustrate the utility of the approach. The most ambitious is an ARFIMA(2,d,2) model for the Campito tree ring time series (length 5405), for which the methods developed in the article provide an essentially uncorrelated sample of size 16,384 from the exact posterior distribution in under four hours. Less ambitious applications take as little as 4 minutes without exploiting GPUs.