Dielectric performance and conductive mechanism of KNN-based ceramics prepared via sol–gel core–shell process

Journal of Materials Science: Materials in Electronics - 0.95(Li0.02Na0.50K0.48)(Nb0.95Sb0.05)O3–0.05AgTaO3@BaZrO3 (LNKNbSAT@BZ) lead-free ceramics were prepared via a sol–gel...     

子集模拟中马尔可夫链蒙特卡洛抽样算法比较

文章着重研究子集模拟中马尔可夫链蒙特卡洛(MCMC)抽样算法的抽样效率与计算精度。首先，阐述可靠度子集模拟的基本原理与中间状态样本生成的各种MCMC抽样算法，在稳态马尔可夫链构造基础上提出延迟拒绝MMH(Modified Metropolis Hasting)算法，通过在MMH算法上增加备选样本的延迟拒绝步提高MMH算法的抽样效率；阐述基于随机游走与基于扩散方程MCMC方法中建议分布的差异，进一步对备选样本接受率为1的preconditioned Crank-Nicolson(pCN)算法和条件抽样(Conditional sampling, CS)算法开展研究，证明两种算法的等价性；推导有效样本量的计算方法，提出采用有效样本量与总样本量的比值定义MCMC方法的抽样效率。通过复杂目标分布的样本生成研究不同MCMC抽样算法建议分布及其参数对备选样本接受率与抽样效率的影响，最后通过计算实例研究子集模拟过程采用不同MCMC抽样算法得到失效概率的相对误差及其变异性，揭示不同MCMC抽样算法对失效概率计算精度的影响。研究表明：不同MCMC抽样算法生成备选样本的接受率及其自相关性受建议分布及其参数影响较大，对于复杂的目标分布，pCN算法和CS算法的抽样效率较高，延迟拒绝MMH算法次之；采用CS算法和延迟拒绝MMH算法进行子集模拟得到的失效概率精度较高且变异性较低；增加子集模拟中间状态样本量可以提高失效概率计算精度并降低其变异性。     

Spatial–Temporal Fusion Based Path Planning for Source Seeking in Wireless Sensor Network

International Journal of Wireless Information Networks - Source seeking problem has been faced in many fields, especially in search and rescue applications. We proposed a virtual structure-based...     

Stabilization for Schrödinger Equation with Internal Damping and Boundary Disturbance

In this paper, the stabilization for Schrödinger equation subject to internal damping and boundary disturbance at the control end is investigated. Due to its immeasurability, the nonlinear observer system is designed to obtain the state information, and the existence of weak solution and its convergence for the nonlinear observer system are proved. The feedback control is realized by the backstepping transformation. In addition, the adaptive disturbance rejection control is applied to estimate the disturbance. According to the observer and disturbance estimation, the feedback control is finally designed to stabilize the system asymptotically.

     

Research on the Failure Characteristics of a Spherical Bearing

Strength of Materials - In order to study the failure process of a large-scale spherical bearing, the finite element simulation method was used to establish the full-scale finite element model of...     

Dynamic voltage scaling based energy-minimized partial task offloading in fog networks

Wireless Networks - With the dynamic voltage scaling (DVS) technology, the terminal node (TN) can dynamically adjust its computational speed, thus providing a new way to save energy during task...     

Graph-Theoretic Method on Topology Identification of Stochastic Multi-weighted Complex Networks with Time-Varying Delayed Coupling Based on Adaptive Synchronization

Neural Processing Letters - This paper is concerned with topology identification of stochastic multi-weighted complex networks based on adaptive synchronization. Different from previous work,...     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.