Wall Rock Alteration,Uranium Mineralization,and Potentiality of Uranium and Iron Dissolution from Mineralized Abu Rusheid Gneiss Rock,South Eastern Desert,Egypt

Radiochemistry - Ferrugination, sericitization, desulfitization, chloritization, and kaolinitization of hydrothermal origin are the main wall rock alterations occurring within the NNW shear zones...     

Map management for robust long-term visual localization of an autonomous shuttle in changing conditions

Multimedia Tools and Applications - Changes in appearance present a tremendous problem for the visual localization of an autonomous vehicle in outdoor environments. Data association between the...     

Comparison between normal and reverse thin crystalline silicon solar cells

The newly developed ingot growing techniques, as the three-grain and the columnar multigrain ingot processes, are now offering the possibility of slicing thinner wafers (≤ 100 μm). In this paper we present the results obtained on p type large area (≥ 100 cm²) and 100 μm thick wafers by using both conventional and reverse cell manufacturing technologies.The conventional cells are provided with aluminium or boron BSF plus screen-printed silver mirror or a silver-aluminium net; the reverse cells have a FSF and the deep back junction completely covered by a screen-printed or CVD silver layer.The constructing parameters have been chosen on the base of one and two dimensions modeling and both raw material and devices have been completely characterized.This work shows that very thin wafers do not introduce serious problems for the conventional manufacturing of solar cells. The efficiencies of the normal and of the reverse cells are found to be comparable and are of the same order than those of thicker cells, however at a significant lower cost. The main obtained result has to be related to the demonstration of a cell manufacturing feasibility starting from very thin wafers.     

Superior activity of a thromboxane receptor antagonist as compared with aspirin in rat models of arterial and venous thrombosis

We determined the effects of aspirin and a novel thromboxane A2/prostaglandin endoperoxide (TP)-receptor antagonist, BMS-180291, on thrombosis and bleeding times in skin and mesenteric arteries. In anesthetized rats, occlusive thrombosis was induced in the carotid artery by topical application of ferrous chloride and in the vena cava by blood flow stasis combined with either infusion of thromboplastin or hypotonic saline. Aspirin (1, 10, and 50 mg/kg) did not reduce arterial or venous thrombus weight significantly. BMS 180,291 (150 micrograms/kg/min) decreased arterial thrombus weight and hypotonic saline-induced caval thrombus weight by 58 and 57%, respectively. BMS-180291 lacked antithrombotic activity at a lower dose (50 micrograms/kg/min) and failed to inhibit thromboplastin-induced caval thrombosis. BMS-180291 (150 micrograms/kg/min) significantly reduced arterial thrombus weight by 40% when plasma epinephrine concentration was increased to 5 ng/ml. BMS-180291 and aspirin produced increases of only < or = 30% in bleeding times. These results demonstrate that BMS-180291 has antithrombotic activity in experimental aspirin-resistant arterial and venous thrombosis. Both aspirin and BMS-180291 have only modest effects on small artery hemostasis in rats.     

Pre-peritoneal bisaccular umbilical and subcutaneous abscess after laparoscopic appendectomy

Laparoscopic surgery has gained much interest since its advent the late eighties. A 36-year-old patient underwent laparoscopic appendicectomy via the transumbilical route. She was rehospitalized three times thereafter for subumblical pain. At day +48, an abscess was evacuated at the point of the umbilical trocar insertion. This hour-glass shaped abscess had a preperitoneal and subcutaneous localization, blocked by the epiploic reaction. The infection this patient developed is an unusual clinical finding as pain was localized at a distance. The umbilical site and the preperitoneal subcutaneous nature of the abscess are also unusual. This case emphasizes the gravity of post-operative abscess of the abdominal wall and the necessity for adequate prophylaxy.     

The putative tumor suppressor gene on chromosome 5q for hepatocellular carcinoma is distinct from the MCC and APC genes

We have previously shown that the tumor suppressor gene for hepatocellular carcinoma (HCC) without cirrhosis may be located on chromosome 5q35-qter. In this study, we analyzed nine cases of primary HCC without cirrhosis using probes from the MCC and APC genes, which are in the region 5q21-22. None of the informative cases had allele loss detected by these probes, whereas the probe lambda MS8 for the region 5q35-qter showed allele loss in six out of six informative cases. The results confirm that the putative tumor suppressor gene for HCC without cirrhosis on chromosome 5q is distinct from the MCC and APC genes.     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.     

Erosion rate correlations of a pipe protruded in an abrupt pipe contraction

Erosion is one of the most serious problems in various gas and liquid flow passages such as flow in pipes, pumps, turbines, compressors and many other devices. Sand presence causes loss of pipe wall thickness that can lead to pipe erosion, frequent failures and loss of expensive production time. The importance of this problem is mainly due to many related engineering applications, viz. heat exchangers. In order to reduce the frequency of such pipe erosions, caps in the form of replaceable pipes are protruded in the sudden contraction regions which are exposed to most of the serious erosion rates. In the present work, numerical investigation of the erosion of a pipe protruded in a sudden contraction is presented. The turbulent, steady, 2-D axi-symmetric flow inside an axi-symmetric abrupt contraction pipe with a pipe protrusion embedded in it was solved by steady-state time averaged conservation equations of mass and momentum along with two equation model for turbulence. Particles are tracked using Lagrangian particle tracking. An erosion model was employed to investigate the erosion phenomena for the given geometry. The influence of the different parameters such as the inlet flow velocity (3–10 m/s), the particle diameter (10–400 μm), the protruded pipe geometry (thickness T=1–5 mm and depth H=2–5 mm) and the pipe contraction ratio (Cr=0.25–0.5) on the erosion of pipe protrusion was investigated. Correlations for the influence of inlet flow velocity, depth and thickness of the protruded pipe on the erosion rate are presented.