Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

Application of bio-based dimer acid diglycidyl ester in paper-based copper clad laminate

Using dimer acid (DA) as raw material, DA diglycidyl ester (DADGE) was synthesized and used as reactive toughening agent to prepare paper-based copper clad laminate (p-CCL). The factors affecting the epoxy value of DADGE and the effect of the resin on the gelation time were studied. The effects of the epoxy value and the addition amount of DADGE on the solderleaching resistance, flammability, water absorption, bending strength, and impact strength of the p-CCL were discussed. The results showed when the molar ratio of DA to ECH was 1:8 and the molar ratio of DA to sodium hydroxide was 1:1.6, the epoxy value of DADGE reached the maximum value of 0.23 mol/100 g. The DADGE can shorten the gelation time of the glue. The p-CCL meets the performance of the IPC-TM-650 standard. And when the addition amount of DADGE is less than 12 wt %, the flammability of the p-CCL reaches UL94V-0 level. The p-CCL prepared by adding 6 wt % of DADGE with 0.08 mol/100 g epoxy value has the best comprehensive performance, its toughness and rigid are comparable to those of p-CCL with 12 wt % of commercially available high performance toughening agents and it has higher solderleaching resistance. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47508.     

Torsional statics of two-dimensionally functionally graded microtubes

A size-dependent governing equation is derived to investigate the torsional static behaviors of two-dimensionally functionally graded microtubes based on the modified couple stress theory. The shear modulus is assumed to vary along the tube’s length direction according to an exponential distribute function, and varies along the tube’s radius direction according to a power-law function. A generalized differential quadrature method is developed to determine the rotational angle and shear stresses. Some illustrative examples are given to investigate the effects of applied torques, the length scale parameter and various material compositions on the torsional angle and shear stresses.     

UV/TiO_2光催化氧化工艺脱汞的试验研究

UV/TiO_2光催化技术在TiO_2催化剂的作用下可将烟气中Hg~0氧化脱除。利用自制的UV/TiO_2氧化试验台研究了影响Hg~0去除率的相关因素,结果表明,在无催化剂和有紫外灯情况下可脱除少量Hg~0;Hg~0去除率随催化剂活性组分含量的增加而上升,但上升速率逐渐下降;在温度(50～200)℃范围内,Hg~0去除率无明显变化;Hg~0去除率随着Hg~0初始浓度的升高逐渐下降;Hg~0去除率随着烟气中氧含量先上升后趋于不变。UV/TiO_2氧化工艺脱汞可为燃煤电厂烟气脱汞提供理论指导。     

可持续煤矿矿井水处理与资源化技术综述

煤矿开采过程中会产生大量的废弃矿井水,不仅造成水资源的大量浪费,而且还威胁着矿区生态环境。本文综述了我国常见矿井水的常规处理方法,以及将矿井水视为水资源的可持续矿井水水处理与资源化技术,首次提出以“时间维度和空间维度”对矿井水进行全时空处理,并着重阐述了矿井水分级处理、分质利用技术,反渗透浓水处理与资源化技术,煤泥处理与资源化技术,以及重金属回收与利用技术等,对煤矿区矿井水处理与资源化利用具有指导意义。     

Densification,mechanical and thermal properties of ZrC1 − x ceramics fabricated by two-step reactive hot pressing of ZrC and ZrH2 powders

Densification behavior, mechanical and thermal properties of ZrC_1 ? x ceramics with various C/Zr ratios of 0.6–1.0 have been investigated by two-step reactive hot pressing of ZrC and ZrH₂ powders at 30 MPa and 1500–2100 °C. The two-step reactive hot pressed ZrC_1 ? x ceramic has a higher relative density (> 95.3%) than that (91.9%) of stoichiometric ZrC sintered at 2100 °C. A cubic Zr₂C-type ordered phase forms in the ZrC_1 ? x sample obtained at a ZrC/ZrH₂ molar ratio of 0.6 at a relatively low temperature of 1100 °C. The decrease in C/Zr ratio is beneficial to densification of ZrC_1 ? x ceramic, however, excess grain growth occurs after sintering above densification temperature. The elastic modulus and Vickers hardness decrease with decreasing the C/Zr ratio. With decreasing the C/Zr ratio, both thermal conductivity and specific heat decrease due to the enhanced scattering of conducting phonons and electrons by carbon vacancies.     

A novel bio‐based phthalonitrile resin derived from catechin: synthesis and comparison of curing behavior with petroleum‐based counterpart

The development of bio‐based thermosetting resins with good thermal stability can potentially afford sustainable polymers as replacements for petroleum‐based polymers. We report a practical route to a novel catechin‐based phthalonitrile resin precursor (CA‐Ph), which contains free phenolic hydroxyl groups that result in ‘self‐curing’ at elevated temperatures to afford a thermostable polymer. Comparison of the performance of this CA‐Ph resin with that of a conventional petroleum‐based bisphenol A phthalonitrile resin (BPA‐Ph; containing 5 wt% of the curing agent 4,4′‐diaminodiphenylsulfone) revealed that CA‐Ph exhibits a lower melting point and curing temperature. Cured CA‐Ph resin retains 95% of its weight at 520 °C under a nitrogen atmosphere, which compares favorably with results obtained for BPA‐Ph resin that retains 95% of its weight at a lower temperature of 484 °C. Kinetic results indicated that the curing reactions of both CA‐Ph and BPA‐Ph systems follow an autocatalytic mechanism. These results suggest that catechin is a useful bio‐based feedstock for the preparation of self‐curing and thermally stable phthalonitrile resins for advanced technological applications. © 2017 Society of Chemical Industry     

电压对微弧氧化膜抑制7050铝合金氢脆敏感性的影响

为进一步探究微弧氧化膜和7050铝合金的氢脆敏感性之间的关系,采用了湿空气中的慢应变速率拉伸、拉伸断口形貌分析、微弧氧化试样表面形貌分析及氢含量测试等表征手段,验证了微弧氧化膜抑制7050铝合金在湿空气中发生氢脆的机制。结果表明,不同微弧氧化电压下制备的膜层对7050铝合金具有不同的抑制氢脆效果,抑制机制主要由膜阻氢进入试样和膜致附加压应力两个方面组成。     

工业园区混合能源优化配置方法应用与实践

为了充分挖掘多能源之间的互补潜力,使工业园区混合能源系统的配置方式由传统粗放式转变为精确优化配置并降低系统配置方案的保守性,基于粒子群联合CPLEX求解算法对工业园区的系统配置和运行调度方案进行分析优化,并以某生物园区为例进行了实例分析,得到了目标函数下的最优设计方案和运行策略。仿真分析结果表明,优化配置方法的应用能够协调冷热电多种能源的混合利用,提升系统的综合经济性。同时,为工业园区能源供应项目的规划、设计提供参考性支撑,丰富设计手段。     

Mediated Electrochemistry to Mimic Biology's Oxidative Assembly of Functional Matrices

Biology uses diffusible oxidants to perform functions that range from signaling to matrix assembly, and these oxidation chemistries offer surprising selectivities. Here, it is reported that mediated electrochemistry can access the richness of such oxidation chemistries. Specifically, electrode‐imposed voltage inputs are used to locally generate oxidized mediators that can diffuse into polymer solutions and induce the formation of covalent bonds for the deposition and functionalization of hydrogels at the electrode surface. Depending on the mediator's redox potential (E⁰), it is possible to “gate” the voltage inputs to target specific residues (e.g., thiols or amines) and oxidation chemistries. Further, mediators of varying E⁰ offer different reactivities and thus allow control of reaction‐diffusion rates to modulate the hydrogel's crosslink density and mechanical properties. Importantly, this mediated oxidation can be performed under physiologically relevant conditions to preserve labile biological functionalities (e.g., cell viability and protein function). Finally, it is demonstrated that protein fusion tags can be engineered to have “targetable” amino acid residues that enable protein function to be oxidatively conjugated to electrodeposited hydrogels. In summary, mediated electrochemistry can engage orthogonal oxidation chemistries to create functionalized matrices and thus mediated electrochemistry should add important capabilities to the electrofabrication toolbox.