Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Evaluation of microbial toxins,trace elements and sensory properties of a high-theabrownins instant Pu-erh tea produced using Aspergillus tubingensis via submerged fermentation

Theabrownins (TB) are polymeric phenolic compounds associated with the multiple bioactivities of Pu-erh tea, a post-fermented Chinese dark tea. High-TB instant Pu-erh tea was produced via a novel submerged fermentation (SF) using Aspergillus tubingensis and compared with samples produced commercially via the conventional solid-state fermentation (SSF). Viable microorganisms and microbial toxins, especially aflatoxins B₁, G₁, B₂, G₂, cyclopiazonic acid, fumonisins B₁, B₂, B₃ and ochratoxin A, were below the detection limit in all samples. Fewer microbial metabolites were found in SF instant tea compared with the SSF teas. Based on an adult consuming 1 g of instant Pu-erh tea daily, the dietary intake of investigated elements was below the safe limits recommended by various authorities. Tasters viewed the instant tea infusions as very mild, smooth, mellow and full. This suggested that submerged fermentation using A. tubingensis offers a speedy and safe alternative to commercial production of instant Pu-erh tea.     

New multi-criteria LNN WASPAS model for evaluating the work of advisors in the transport of hazardous goods

Neural Computing and Applications - Successfully organizing the transport of hazardous materials and handling them correctly is a very important logistical task that affects both the overall flow...     

Detailed microkinetic modelling of syngas to hydrocarbons via Fischer Tropsch synthesis over cobalt catalyst

Fuels production from syngas via Fischer Tropsch synthesis (FTs) is an alternative technology for clean energy production. The microkinetic model is a promising approach for gaining insight into FTs activity. In this study, a systematic microkinetic model was proposed to develop a process for cobalt-catalyzed FTs. All possible elementary reactions based on the carbide mechanism and characteristics of catalyst sites were considered in the kinetic model. The effects of the reaction rate constant, reaction pathways, and H₂ to CO ratio were represented by a kinetic parameter, reaction path, and operating parameter, respectively. The model could accurately predict product distribution trends, with an R² value and mean absolute relative residuals percentage of 0.91–0.93 and 5–43%, respectively, in comparison with experimental data. Hydrogen utilization was predicted and analyzed. High model accuracy was achieved, with a 10^?10–10^?3% error in the material balance.     

Anticancer Potential of (Pentamethylcyclopentadienyl)chloridoiridium(III) Complexes Bearing κP and κP,κS‐Coordinated Ph2PCH2CH2CH2S(O)xPh (x=0–2) Ligands

Iridium(III) complexes of the type [Ir(η⁵‐C₅Me₅)Cl₂{Ph₂PCH₂CH₂CH₂S(O)_xPh‐κP}] (x=0–2; 1 – 3 ) and [Ir(η⁵‐C₅Me₅)Cl{Ph₂PCH₂CH₂CH₂S(O)_xPh‐κP,κS}][PF₆] (x=0–1; 4 and 5 ) with 3‐(diphenylphosphino)propyl phenyl sulfide, sulfoxide, and sulfone ligands Ph₂PCH₂CH₂CH₂S(O)_xPh were designed, synthesized, and characterized fully, including X‐ray diffraction analyses for complexes 3 and 4 . In vitro studies against human thyroid carcinoma (8505C), submandibular carcinoma (A253), breast adenocarcinoma (MCF‐7), colon adenocarcinoma (SW480), and melanoma (518A2) cell lines provided evidence for the high biological potential of the neutral and cationic iridium(III) complexes. Neutral iridium(III) complex 5 proved to be the most active, with IC₅₀ values up to about 0.1 μM , representing activities of up to one order of magnitude higher than cisplatin. Using 8505C cells, apoptosis was shown to be the main mechanism through which complex 5 exerts its tumoricidal action. The described iridium(III) complexes represent potential leads in the search for novel metal‐based anticancer agents.     

Azimuthally oscillating membrane emulsification for controlled droplet production

A novel membrane emulsification (ME) system is reported consisting of a tubular metal membrane, periodically azimuthally (tangentially) oscillated with frequencies up to 50 Hz and 7 mm displacement in a gently cross flowing continuous phase. A computational fluid dynamics (CFD) analysis showed consistent axial shear at the membrane surface, which became negligible at distances from the membrane surface greater than 0.5 mm. For comparison, CFD analysis of a fully rotating ME system showed local vortices in the continuous phase leading to a variable shear along the axis of the membrane. Using an azimuthally oscillating membrane, oil‐in‐water emulsions were experimentally produced with a median diameter of 20–120 μm, and a coefficient of variation of droplet size of 8%. The drop size was correlated with shear stress at the membrane surface using a force balance. In a single pass of continuous phase, it was possible to achieve high dispersed phase concentrations of 40% v/v. © 2015 American Institute of Chemical Engineers AIChE J, 61: 3607–3615, 2015     

Ultrasmall Nanoplatforms as Calcium‐Responsive Contrast Agents for Magnetic Resonance Imaging

The preparation of ultrasmall and rigid platforms (USRPs) that are covalently coupled to macrocycle‐based, calcium‐responsive/smart contrast agents (SCAs), and the initial in vitro and in vivo validation of the resulting nanosized probes (SCA‐USRPs) by means of magnetic resonance imaging (MRI) is reported. The synthetic procedure is robust, allowing preparation of the SCA‐USRPs on a multigram scale. The resulting platforms display the desired MRI activity—i.e., longitudinal relaxivity increases almost twice at 7 T magnetic field strength upon saturation with Ca²⁺. Cell viability is probed with the MTT assay using HEK‐293 cells, which show good tolerance for lower contrast agent concentrations over longer periods of time. On intravenous administration of SCA‐USRPs in living mice, MRI studies indicate their rapid accumulation in the renal pelvis and parenchyma. Importantly, the MRI signal increases in both kidney compartments when CaCl₂ is also administrated. Laser‐induced breakdown spectroscopy experiments confirm accumulation of SCA‐USRPs in the renal cortex. To the best of our knowledge, these are the first studies which demonstrate calcium‐sensitive MRI signal changes in vivo. Continuing contrast agent and MRI protocol optimizations should lead to wider application of these responsive probes and development of superior functional methods for monitoring calcium‐dependent physiological and pathological processes in a dynamic manner.     

Ultrastructural changes in the cemento‐enamel junction caused by acidic beverages: An in vitro study

The present in vitro study was aimed at evaluating the morphological changes in the cemento‐enamel junction (CEJ) after exposure to acidic beverages using the scanning electron microscopy (SEM). The initial pH and titratable acidity (TA) was analyzed from follow groups: (I) Coca cola, (II) orange juice, (III) Cedevita, (IV) Red Bull, (V) Somersby cider, and (VI) white wine. The CEJ samples (n = 64), obtained from unerupted third molars, were allocated to one control (artificial saliva, n = 16) and six experimental groups (n = 8). The experimental samples were immersed in beverages (50 ml) for 15 min, three times daily, 10 days, and in artificial saliva between immersions. SEM analysis was performed in a blind manner, according to scoring scale. One‐way ANOVA and Tukey's post hoc tests, as well as Kruskal–Wallis and Mann–Whitney U test used for statistical analysis. The pH values of the acidic beverages ranged from 2.65 (Coca cola) to 3.73 (orange juice), and TA ranged from 1.90 ml (Coca cola) to 5.70 ml (orange juice) of NaOH to reach pH 7.0. The SEM analysis indicated statistically significant differences between the control samples and those immersed in acidic beverages. The Groups IV, I, and II, showed the highest CEJ damage grade while those of the Group VI were the lowest. All the tested acidic beverages caused morphological changes in the CEJ with a smaller or larger exposure of dentine surface, and were not always related to the pH or TA of acidic beverages.     

Production of stable amorphous form by means of spray drying

Spray drying is a very useful method for manufacturing of amorphous solid materials. This is mainly due to the possibility of fast solvent evaporation that leads to a rapid transformation of solution to a solid state. Besides evaporation kinetics, there are various process parameters that influence physical and chemical characteristics of such obtained material. The possibility of obtaining a stable amorphous structure of the active pharmaceutical ingredient in a spray dryer was examined. A solution of the hydrochloride crystalline structure of the active pharmaceutical ingredient in a mixture of water and acetonitrile was dried at different temperatures and flowrates of nitrogen used for atomization, as well as the flowrates of the solution. The influence of the process conditions on the properties of the product was analyzed. The final dried products were characterized and identified with a variety of analytical and physical methods. The results showed that a stable amorphous structure of the high purity active pharmaceutical ingredient is obtained, and that the optimal conditions of the process are defined. The amorphous structure is stable at temperatures below 200°C when it is transformed into a new crystal structure. Conditions of high relative air humidity lead to partial transformation.