车用复合材料板簧性能的有限元分析

为了初步验证所设计复合材料板簧的结构性能,利用有限元分析方法对复合材料板簧结构的静载力学和动态疲劳进行了研究。计算得到空载工况加载过程中的载荷—位移曲线,板簧刚度为373 N/mm。当两端施加载荷为64.7 kN时,板簧达到最大压缩应力。结合复合材料的S—N曲线对板簧寿命进行了估算,循环次数最低处位于板簧下表面靠近卷耳部分,循环次数为33万次。对比复合材料板簧的设计刚度和疲劳寿命,与有限元分析处理方法计算所得结果较为接近,该板簧结构基本符合使用要求。     

Using electroencephalogram to continuously discriminate feelings of personal thermal comfort between uncomfortably hot and comfortable environments

Thermal comfort is an important factor for the design of buildings. Although it has been well recognized that many physiological parameters are linked to the state of thermal comfort or discomfort of humans, how to use physiological signal to judge the state of thermal comfort has not been well studied. In this paper, the feasibility of continuously determining feelings of personal thermal comfort was discussed by using electroencephalogram (EEG) signals in private space. In the study, 22 subjects were exposed to thermally comfortable and uncomfortably hot environments, and their EEG signals were recorded. Spectral power features of the EEG signals were extracted, and an ensemble learning method using linear discriminant analysis or support vector machine as a sub-classifier was used to build the discriminant model. The results show that an average discriminate accuracy of 87.9% can be obtained within a detection window of 60 seconds. This study indicates that it is feasible to distinguish whether a person feels comfortable or too hot in their private space by multi-channel EEG signals without interruption and suggests possibility for further applications in neuroergonomics.     

Preparation of ZrC/SiC porous self-supporting monoliths via sol-gel process using polyethylene glycol as phase separation inducer

We present a straightforward method via sol-gel process using polyethylene glycol (PEG) as phase separation inducer to prepare zirconium carbide/silicon carbide (ZrC/SiC) porous monoliths. Organic/inorganic hybrid gels are prepared using zirconium oxychloride, furfuryl alcohol, and tetraethyl orthosilicate as major starting materials. In the presence of PEG, crack-free hybrid monoliths are obtained by drying the wet gels under ambient pressure, whereas in the absence of PEG, the wet gels break into pieces as expected. PEG plays a key role in maintaining the macroscopic shape of the monoliths. After ceramization at 1300–1500?°C, ZrC/SiC porous monoliths are obtained. SEM and mercury intrusion porosimetry data show that PEG also has strong influence on the microstructures of the monoliths. The compressive strengths of the ceramic monoliths are in the range of 0.3 to 0.7?MPa. And their compressive behavior starts to differ due to the changes in their microstructures, especially the pore structure.     

基于热电效应的高效环控系统

部分空间科学实验对环境温度有较高的要求，环境温度高于或低于空间科学系统能够提供的热沉温度，需要有可靠有效的加温降温处理措施。使用可靠性强的热电制冷片作为制冷制热方式和气液换热器二次换热来实现环境温度控制的需求，并对不同流体温度制冷制热效果进行分析，结果表明流体温度和目标温度差越小，热电制冷制热的效果越好。在环境温度制冷工况中，热电单元数量随电流增加先减少后增加，在制热工况中则单调递减，设计中需按照制冷工况进行热电单元数量的确定。当流体温度接近制冷制热的目标温度时，会出现整个系统总效率优于热电系统效率的区间。通过对热电单元和气液换热器的组合系统的性能计算，提供一种适于热电环控系统的计算方法和部件选型思路，对空间站环控系统的设计有重要参考意义。     

石墨烯热电器件栅控特性研究

为了获得一种稳定可控的能源，提出一种栅控石墨烯热电器件。通过对石墨烯通道的载流子输运机理的分析，获得了温度和栅压对通道电阻的影响。依据半经典Mott公式推导了石墨烯塞贝克系数的表达式，同时给出了石墨烯的电导率和热导率模型。最后通过有限元分析(FEA)建模获得不同栅压条件下的器件温度，当栅极电压V_B=0 V时，石墨烯热电器件热端和冷端温度差为30 K；当V_B=6 V时，最大温差达到50 K；当V_B=30 V时，最小温差只有10 K。结果表明，栅压对热电器件的性能有明显的调控性。该研究可为石墨烯热电器件的设计提供理论参考。     

基于CAN总线的舵机控制系统设计

主要介绍了一种基于CAN总线的舵机控制系统。系统以CAN总线作为通信方式，PWM控制信号通过硬件方式产生，具有结构简单、信号稳定和实时性强的特点。     

从微电子到"活动的硅"--系统集成的未来潜力

本文主要介绍微电子发展趋势、微电子与微机械结合、系统集成的未来潜力。     

聚甲亚胺改性尼龙6复合材料的等温结晶动力学

采用差示扫描量热法（DSC）对聚甲亚胺（PAM）/尼龙6复合材料等温结晶过程进行了研究。结果表明，PAM的加入使得基体的结晶速率增大，尤其是当含量为5%时，半结晶期明显减少。研究还发现，该体系的等温结晶过程完全可以用Avrami方程来描述，各试样的Avrami指数均在2-3之间，表明Avrami指数，球晶生长方式基本不受聚甲亚胺加入的影响。基体中原位形成的聚甲胺微纤起到了诱导结晶的作用，使得基体的结晶速率加快，但随着微纤含量的增加，由于分散性能变差而使得诱导结晶的能力减弱，表现为结晶速率又有所降低。