Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

Air-Coupled Ultrasonic Resonance Imaging of Hexagonal SiC and Alumina Tiles

Resonant ultrasound spectroscopy (RUS) is an NDE technique that evaluates a sample based on its predicted resonant behavior, but RUS is limited by lack of spatial resolution and small specimen size. Air-coupled ultrasonic resonance imaging (ACURI) is a new NDE technique that is based on RUS but introduces a spatial resolution by generating an image of the flexural vibration modes. This paper presents experimental results of ACURI applied to hexagonal silicon carbide tiles. Frequency sweep scans demonstrate the ability of air-coupled transducers to detect resonance modes. Several mode shapes are imaged and compared to Finite Element simulations with good agreement. Visual comparison allows for easy detection of material differences such as density variations.     

Influence of Inclusion and Specimen Orientations on Intergranular Corrosion Testing of AISI 316LN Stainless Steel

Fabricated components must be free from sensitization for using these in critical applications in aggressive environments. During fabrication of a hollow bar from solid bar, deep hole drilling was employed which introduces residual stresses. Stress-relieving heat treatment was employed by heating the hollow bar from room temperature to 1,065°C @ 40°C/h and soaking at 1,065°C for 1 h followed by cooling @ 40°C/h as well as 70°C/h. To detect the susceptibility to IGC, specimens were taken from both circumferential direction as well as longitudinal direction and subjected to ASTM A 262 Practice E test. In U bend, the specimens from the circumferential direction failed whereas longitudinal specimens did not fail. However specimens of both orientations showed Step structure in Practice A test indicating that no carbide has nucleated during the stress-relieving heat treatment ensuring that the cooling rates are faster than the critical cooling rates and the material is not susceptible to IGC. EDAX studies indicated the presence of numerous MnS inclusions enriched in chromium which might have led to chromium depletion around the inclusions resulting in poor passivity at these locations. This study presents the influence of orientation of MnS inclusions in causing failure in U bend test. The need to select specimens of correct orientation during IGC testing is emphasized in this investigation.     

Conceptual Design of Unpressurized Shelters on Lunar Surface

Three concepts for the shelters on the moon are presented here. It is envisaged that the first robots will land on the moon and start preparing sites for advanced bases and also for future human presence. These robots will encounter severe radiation and micrometeor hits when they are exposed to the lunar atmosphere. During the period of intense solar radiation these robots have to be temporarily sheltered, since shielding on the robots may not be adequate to protect the instruments. The construction of these shelters has to be performed with very little equipment support. This paper presents concepts and their feasibility analysis for the fabrication of shelters under such stringent constraints.     

A new efficient optimal path planner for mobile robot based on Invasive Weed Optimization algorithm

Planning of the shortest/optimal route is essential for efficient operation of autonomous mobile robot or vehicle. In this paper Invasive Weed Optimization (IWO), a new meta-heuristic algorithm, has been implemented for solving the path planning problem of mobile robot in partially or totally unknown environments. This meta-heuristic optimization is based on the colonizing property of weeds. First we have framed an objective function that satisfied the conditions of obstacle avoidance and target seeking behavior of robot in partially or completely unknown environments. Depending upon the value of objective function of each weed in colony, the robot avoids obstacles and proceeds towards destination. The optimal trajectory is generated with this navigational algorithm when robot reaches its destination. The effectiveness, feasibility, and robustness of the proposed algorithm has been demonstrated through series of simulation and experimental results. Finally, it has been found that the developed path planning algorithm can be effectively applied to any kinds of complex situation.     

Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.     

The effects of noise on frequency-domain parameter estimation ofsynchronous machine models

The authors present results of a study conducted to evaluate the effects of measurement noise on the estimation of machine parameters from standstill frequency response test data. Results obtained indicate that, because the test data are inherently noise-corrupted, multiple solution sets can be obtained. Moreover, some of the estimated machine parameters could be unrealistic. It is shown that the results are very sensitive to the value of armature resistance used in the data analysis. Even a 0.5% error in the value of armature resistance could result in unrealistic estimation of the machine parameters     

Ultrasonic nondestructive evaluation of fibre-reinforced composite materials — a review

A framework is presented for examining the effectiveness of limiting and modelling arguments used in the analysis of fluid flows. It consists of examining the consequences of the arguments on the flow problem as a whole and breaking down the limiting/modelling process into a sequence of steps and associated sequence of flow problems, termed here as ‘lidels’. The notion of validity of lidels is given. Several examples are given to explain the present approach. Invited general lecture at 3rd ACFM, Tokyo, September 1986