Fabrication and piezoelectric properties of BaTiO3/BaTiO3-Bi(Mg1/2Ti1/2)O3-BiFeO3 composites

We fabricated xBaTiO₃ (BT)/(1-x)[BaTiO₃-Bi(Mg_1/2Ti_1/2)O₃-BiFeO₃] (BT-BMT-BF)?+?0.1?wt%MnCO₃ composites by spark plasma sintering and investigated the effect of BT content x, BT powder size, and BT-BMT-BF composition on piezoelectric properties. For xBT/(1-x)(0.3BT-0.1BMT-0.6BF) +?0.1?wt%MnCO₃ (x?=?0–0.75) composites with a 0.5-µm BT powder, the dielectric constant was increased with x, and the relative density was decreased at x?=?0.67 and 0.75, creating optimum BT content of x?=?0.50 with a piezoelectric constant d₃₃ of 107?pC/N. When a larger 1.5-µm BT powder was utilized for the composite with x?=?0.50, the d₃₃ value increased to 150?pC/N due to the grain size effect of the BT grains. To compensate for a compositional change from the optimum 0.3BT-0.1BMT-0.6BF due to partial diffusion between the BT and 0.3BT-0.1BMT-0.6BF grains, a 0.5BT/0.5(0.275BT-0.1BMT-0.625BF)?+?0.1?wt%MnCO₃ composite with the 1.5-µm BT powder was fabricated. We obtained an increased d₃₃ value of 166?pC/N. These results provided a useful composite design to enhance the piezoelectric properties.     

Measurements of thermal-neutron capture cross-section of Cesium-135 by applying mass spectrometry

ABSTRACT

The thermal-neutron capture cross-section (σ₀) and resonance integral (I₀) were measured for the ¹³⁵Cs(n,γ)¹³⁶Cs reaction by an activation method and mass spectrometry. Because of difficulty in the preparation of pure ¹³⁵Cs samples, we used ¹³⁵Cs contained as an impurity in a normally available ¹³⁷Cs standard solution. An isotope ratio of ¹³⁵Cs and ¹³⁷Cs in a standard ¹³⁷Cs solution was measured by mass spectrometry to quantify ¹³⁵Cs. Cesium-135 impurity along with the ¹³⁷Cs standard solution was irradiated at the hydraulic conveyer of the research reactor in the Institute for Integral Radiation and Nuclear Science, Kyoto University. Wires of Co/Al and Au/Al alloys were used as neutron monitors to measure thermal-neutron fluxes and epi-thermal Westcott’s indices at an irradiation position. A gadolinium filter was used to measure the σ₀, and a value of 0.133 eV was taken as the cut-off energy. Gamma-ray spectroscopy was used to measure induced activities of ¹³⁷Cs, ¹³⁶Cs and monitor wires. On the basis of Westcott’s convention, the σ₀ and I₀ values were derived as 8.57 ± 0.25 barn, and 45.3 ± 3.2 barn, respectively. The value of σ₀ obtained in the present study agreed within the limits of uncertainties with the past-reported value of 8.3 ± 0.3 barn.     

Frequency of Upward Lightning Hits to Wind Turbines in Winter

In recent years, frequent damage to wind turbines by winter lightning has been reported in the region along the Sea of Japan. It is a serious finding that lightning hits concentrate on wind turbines in this region. The authors investigated the increase rate of the frequency of lightning hits on wind turbines due to wind turbine construction by using LLS (lightning location system) data. As a result, an experimental formula to estimate the increase rate of the frequency of lightning hits on wind turbines as a function of parameters related to the construction conditions, namely the height of wind turbines, the height above sea level, and the latitude, is proposed.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

Practical Continuous‐Flow Controlled/Living Anionic Polymerization

A continuous‐flow reaction system was developed, allowing flow conditions of the entire system to be maintained at a predetermined constant level, which is one of the most significant factors for successful industrial application. Controlled/living anionic polymerization was selected as a model reaction since the characteristics of its polymer products, molecular weights, and molecular weight distributions are highly susceptible to changes in the relative flow rates of a monomer and initiator solutions. In flow microreactors, controlled/living anionic polymerization of styrene in tetrahydrofuran (THF)/hexane initiated by THF‐diluted n‐butyllithium (n‐BuLi) was examined. Poly(styrenes) of larger molecule sizes such as Mn > 15 000 were successfully synthesized. After continuous operation for four hours, ca. 0.5 kg of the polymer was readily produced with narrow molecular weight distribution, demonstrating the applicability of this continuous‐flow system for controlled/living anionic polymerization on considerably large scale with a view to its industrial usage in the future.     

Effect of addition of corrosion inhibitors on corrosion behaviors of PCV material under diluted artificial seawater environment

ABSTRACT

Fukushima Daiichi nuclear power plants (1F) were damaged by unprecedented severe accident in the great east Japan earthquake, and seawater and freshwater had been injected as an emergency countermeasure for the core cooling. Although, the primary containment vessel (PCV) was not supposed to be exposed to diluted seawater, the PCV will be exposed to diluted seawater environment until fuel debris removal is completed. Therefore, it is necessary to establish a countermeasure of corrosion for the PCVs made of carbon steel. In this study, the effect of the addition of corrosion inhibitor, which is one of the corrosion countermeasures, was investigated by two types of corrosion tests. As a result of the immersion corrosion test, it was found that any of the three kinds of corrosion inhibitor could suppress corrosion of carbon steel. In addition, as a result of the inhibitor interim addition test, it was found that corrosion of carbon steel covered with corrosion products could be suppressed by optimizing the additive amount of corrosion inhibitor in the cooling water.     

Stabilizing effect of the cyclodextrins additive to spray-dried particles of curcumin/polyvinylpyrrolidone on the supersaturated state of curcumin

Although curcumin is considered to have various therapeutic effects, its use as a functional food or supplement is restricted owing to its low water solubility and bioavailability. To increase the solubility of curcumin in water, the use of polyvinylpyrrolidone (PVP) and vinylpyrrolidone-vinyl acetate copolymers with a pyrrolidone skeleton was noted to be promising. In particular, the bi-component formulations of curcumin/PVP prepared through spray drying exhibited an amorphous state in powder X-ray diffraction observations and temporally increased the apparent solubility of curcumin to over 5000 times that of untreated curcumin; nevertheless, after 24 h, the solubility decreased owing to the unstable supersaturated state of curcumin. The addition of α-cyclodextrin (α-CyD) in the bi-component curcumin/PVP formulation helped maintain the supersaturated state of curcumin, whereas the addition of β- and γ-CyD led to the collapse of the supersaturated state. The addition of α-CyD can likely help inhibit the nucleation and crystal growth of curcumin, through the interaction among the solubilized units of curcumin/PVP and α-CyD.     

吴也凡的唯美天驹艺术

<正>吴也凡原创陶瓷艺术作品新加坡展选登——天驹系列No.5、No.6(55×112cm)景德镇陶瓷学院教授、景德镇中外陶瓷艺术协会艺术总监吴也凡博士(改革开放后厦门大学最早培养的几批博士之一)系晚清两房进士之后,1953年出身于名门艺术世家,自幼在当地名师指导下勤习书法与绘画,还受过良好的音乐教育。1966年开始的文化大革命摧残了一代人的梦想。1968年吴也凡通过亲友介绍在衡阳界牌的瓷厂学习画瓷,此后就一直与陶瓷美术有了不解之缘。文革动乱结束后,举国上下科技兴国,从1980