Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

A strategy for defects healing in 3D printed ceramic compact via cold isostatic pressing: Sintering kinetic window and microstructure evolution

In this study, we developed a unique defect healing method for 3D printed ceramic compact via cold isostatic pressing (CIP) after debinding, and typical features of interlayer interface defects of 3D-printed zirconia compact were characterized and found to be reduced significantly. The characteristic sintering kinetics window and microstructure evolution of the healed sintered bodies were systematically investigated, which was found to be quite different from conventional shaping methods. The three sintering stages are probed by their feature microstructure details such as the mechanically flattening surface at the early sintering stage, the heterogeneous microstructure and high porosity in the interlayer interface region at the middle stage, and the slightly ripple-like structural features combined with the healed interlayer defects at the final stage. The evolution of the pore structure of the healed 3D printed bodies were traced and the mechanical properties such as the Young's modulus, hardness, and fracture toughness were measured to understand the significance of the heal effect.     

依托泊苷联合卡铂用于复发性髓母细胞瘤患儿的疗效与安全性

目的:探讨依托泊苷联合卡铂用于复发性髓母细胞瘤患儿的疗效与安全性。方法:选取浙江大学医学院附属儿童医院在2011年1月至2014年6月收治的72例复发性髓母细胞瘤患儿（3～15岁），随机分为CE组和对照组，每组36例，CE组采用依托泊苷＋卡铂给药方式化疗；对照组采用经典伊立替康＋替莫唑胺＋长春新碱方案化疗。比较两组患儿临床疗效、卡诺夫斯基健康状况量表（KPS）评分、儿科生活质量测定量表4.0（PedsQLTM4.0）评分、总生存期（OS）、无事件生存（EFS），记录患儿治疗期间药物不良反应的发生情况。结果:治疗后CE组和对照组完全缓解率（CR）分别为41.67%（15/36）和27.78%（10/36），总缓解率（OR）分别为94.44%（34/36）和77.78%（28/36），差异有统计学意义（P<0.05）。两组患儿治疗前KPS评分及PedsQLTM4.0评分无统计学差异（P＞0.05），治疗后CE组和对照组的KPS评分分别为（80±8）和（75±10）分，PedsQLTM4.0评分分别为（89±11）和（84±11）分，差异均有统计学意义（均P<0.05）。截至末次随访时间，CE组有3例失访，对照组有2例失访。截至末次随访时间，CE组和对照组总生存率分别为78.8%（26/33）和55.9%（19/34），差异有统计学意义（P<0.05），无事件生存率分别为72.7%（24/33）和52.9%（18/34），差异无统计学意义（P＞0.05）。CE组化疗期间共出现10例3级以上不良反应，发生率为27.78%（10/36），对照组化疗期间共出现9例3级以上不良反应，发生率为25.00%（9/36），差异无统计学意义（P＞0.05）。结论:依托泊苷联合卡铂方案能够明显提高患儿临床缓解率，延长患儿总生存率，同时不增加化疗不良反应，但对无事件生存率的影响并不明显。     

基于步冷试验的2.25Cr-1Mo-0.25V钢母材及焊缝回火脆化研究

对原始态、步冷态、脱脆态和脱脆步冷态2.25Cr-1Mo-0.25V钢母材及焊缝冲击试验结果进行分析,得到了母材和焊缝在不同状态下的韧脆转变温度vTr54.2和FATT以及脆化度ΔvTr54.2和ΔFATT。试验结果表明,步冷试验之后,母材发生较低程度脆化或脱脆现象,但是脆化度或脱脆度较低,表明母材具有良好的抗回火脆化性能;经脱脆试验后,母材和焊缝都发生较高程度的脱脆,表明材料的脆化主要是由于回火脆化引起的,脱脆试验使得材料的韧脆转变温度降低;脱脆步冷试验后,焊缝发生较高程度的脆化,焊缝对脱脆步冷试验的敏感性较高,脱脆步冷试验有效促进了焊缝的脆化。在相同脆化条件下,母材的脆化敏感性低于焊缝,焊缝更易发生脆化。     

Investigation of machining and wear performance of various diamond micro-grinding tools

The International Journal of Advanced Manufacturing Technology - The wear of micro-grinding tools less than 1 mm in diameter is crucial for achieving acceptable surface quality and accurate...     

12CrNi3钢外锁止套局部表面激光淬火工艺

利用半导体激光宽带对12CrNi3外锁止套局部进行表面淬火处理,并对处理后的零件进行外观检验、显微组织观察、硬度检测分析和摩擦磨损试验。试验结果表明:采取定光斑方式,激光头到工件表面扫描区域中心点距离375 mm(离焦量为0),工件倾斜22°,激光头倾斜18°,温度1350 ℃,扫描速度9 mm/s,单道扫描后表面平整性最好。表面激光淬火硬化层为750～1000 μm,最浅处为443.1 μm,硬化区组织为极细小马氏体组织,硬度达600～700 HV0.2,是基体硬度的2倍左右, 约为渗碳+淬火态硬度的1.3倍,且相变硬化区耐磨性能明显提高。     

Controllable layer-by-layer assembly based on brucite and alginates with the assistance of spray drying and flame retardancy influenced by gradients of alginates

With the aim of tailoring and controlling surface assembly, multifunctional flame retardants (FRs) were obtained based on depositing alginates and silane coupling agents on brucite via the spray-drying-assisted layer-by-layer assembly technique. The assembly was controllable in both structure and gradient mass. Two series of FRs were named CuFR1-3 and NiFR1-3 based on the assembly content of metal alginates. With the assistance of spray drying, good compatibility between FRs and ethylene-vinyl acetate (EVA) was obtained, resulting in better mechanical properties. Meanwhile, the FRs improved flame retardancy and smoke suppression when used in EVA composites. With 55 wt % loading, composites with CuFR3 and NiFR1 passed UL 94 V-0 rating, while those with brucite were not rated. The peak of heat release rate decreased by 51.7 and 49.3% while the residue increased by 9.8 and 11.9%, respectively. The FRs also reduced the smoke and CO production rates. For the two series of FRs, the relationship between FR efficiency and alginate contents is different. The CuFRs assembled more copper alginates and exerted better flame retardancy caused by lower catalytic graphitization. NiFRs exerted a higher catalyzing efficiency at low assembly content. However, at high assembly content, the catalytic graphitization effect would decrease by thermally oxidized degradation leading to excess nickel alginates. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 47570.     

Novel poly(aryl ether nitrile ketone) foams and the influence of copolymer structure on the foaming result

Novel poly(aryl ether nitrile ketone) foams were prepared through the batch foaming method with supercritical CO₂ as the blowing agent. Both temperature‐induced and pressure‐induced foaming methods were conducted to examine the influence of nitrile groups on the foaming result. The results indicated that nitrile groups influenced the foaming result by affecting both the viscoelasticity and CO₂ absorption of the polymers. In addition, the CO₂ solubility of the polymers increased with increasing CN content presumably because of the Lewis acid–base nature of the interaction between the CO₂ molecules and the nitrile groups. The cell growth process was assessed by analyzing the influence of foaming temperature and foaming time on the cell morphology. Nanocellular foams with a minimum size of 30–50 nm were achieved by the temperature‐induced foaming method. Moreover, highly expanded foams with a maximum expansion ratio of 23.6 were obtained by the pressure‐induced foaming method. © 2018 Society of Chemical Industry