基于(火用)效率目标的环冷机余热回收系统操作参数优化

摘要：针对烧结环冷机余热回收利用率不高的难题，采用分析法建立了评价某钢铁厂烧结环冷机余热回收系统运行效率的效率模型。基于多孔介质模型、局部非热平衡方程、真实气体SRK方程建立环冷机内气固两相换热模型。通过CFD仿真模拟，探究料层高度、循环风机输入烟气温度、烧结矿底部入口风速三项可控环冷机运行工艺参数对系统效率的影响规律。结果表明，料层厚度在1～1.5 m区间每增加0.1 m，效率增加0.8%～1.1%；循环风温在100～140℃之间每增加10℃，效率增加1.4%～1.5%；烧结矿底部入口风速在0.9～1.9 m/s之间每增加0.1 m/s，效率降低0.18%～0.24%。在此基础上，基于工业运行数据建立效率正交试验优化模型，提高了该余热回收系统3.42%的效率。     

首钢烧结配加扬地粉试验研究

介绍了首钢原料条件下配加扬地粉对烧结生产影响的实验室研究.随着扬地粉配入量的增加,烧结矿转鼓强度、成品率改善,燃耗有少量上升,利用系数增加,低温还原粉化指数变差.研究结果表明:在首钢目前条件下,配入10%～20%的扬地粉是可行的.二烧车间进行了扬地粉工业试验,其最高配比达到30%,工业试验时烧结各项指标变化与实验室试验结果基本一致.     

近年来攀钢烧结工序采用的新技术

为了提高烧结矿强度、改善烧结矿粒度组成，提高烧结矿质量，对近年来攀钢烧结工序采用的一些新技术及其效果作了系统介绍。     

From Long Infrared to Very Long Infrared Wavelength Focal Plane Arrays Made with HgCdTe n + n ?/ p Ion Implantation Technology

This paper aims at studying the feasibility of very long infrared wavelength (VLWIR) (12–18 μm) focal plane arrays using n-on-p planar ion-implanted technology. To explore and analyze the feasibility of such VLWIR detectors, a set of four Cd _x Hg_1−x Te LPE layers with an 18 μ cutoff at 50 K has been processed at Defir (LETI/LIR–Sofradir joint laboratory), using both our “standard” n-on-p process and our improved low dark current process. Several 320 × 256 arrays, 30-μm pitch, have been hybridized on standard Sofradir readout circuits and tested. Small dimension test arrays characterization is also presented. Measured photonic currents with a 20°C black body suggest an internal quantum efficiency above 50%. Typical I(V) curves and thermal evolution of the saturation current are discussed, showing that standard photodiodes remain diffusion limited at low biases for temperatures down to 30 K. Moreover, the dark current gain brought by the improved process is clearly visible for temperatures higher than 40 K. Noise measurements are also discussed showing that a very large majority of detectors appeared background limited under usual illumination and biases. In our opinion, such results demonstrate the feasibility of high-performance complex focal plane arrays in the VLWIR range at medium term.     

降低烧结返矿率的途径与实践

通过对影响烧结返矿率的因素进行分析，从优化配料、强化制粒和造球、提高料层厚度、实现低碳低水均质烧结等几个方面着手，使烧结返矿率从1998年的23．6％降到了2003年的16．9％。     

Al2O3在钒钛烧结矿中的行为研究

针对攀钢钒钛烧结矿Al2O3含量高的情况，在实验室对Al2O3在钒钛烧结矿中的行为进行了试验研究，结果表明，Al2O3含量增加对钒钛烧结矿的产量，质量有不利影响，钒钛烧结矿中的Al2O3主要以固溶体形式贮存于除钙钛矿外的其他矿物相，它对烧结矿的矿物组成和结构有较大的影响。     

W-Ni-Cu高比重合金注射成形烧结收缩及性能的研究

研究了W-Ni-Cu高比重合金注射成形工艺过程收缩率和性能。比较了模具尺寸、注射坯尺寸、烧结坯尺寸，及烧结阶段各方向收缩率的关系，发现实际收缩与理论预测收缩率较为一致，但在厚度方向存在与其他方向收缩不一致的情形，这与由重力作用产生的塑料流动有关；还探讨了烧结坯密度与烧结条件的关系，测定了烧结坯的力学性能及断口形貌、金相组织，烧结坯在1400℃，90min烧结达到了99％的相对密度，断裂强度600MPa以上。     

Hydrothermal Synthesis and Low-Temperature Sintering of Zinc Gallate Spinel Fine Particles

Nanosized powders of single-phase zinc gallate (ZnGa₂O₄) spinel were hydrothermally synthesized from solutions in the presence of NaOH over the pH range of 1.9 to 7.0 and from solutions above pH 7.0, i.e., the very basic medium (pH of 13.85), by removing the residual ZnO phase by washing with aqueous H₂SO₄ from the precipitate mixtures of zinc gallate spinel particles and ZnO. A very wide compositional range (Zn/2Ga = 0.705–1.157) of zinc gallate spinel solid solutions could be hydrothermally synthesized in the form of nanosized particles from acid and very basic mediums (pH of 2.4–13.85) in the presence of NaOH. These hydrothermally synthesized spinel powders showed good sinterability and almost full densification at 1100°C for 1 h. Dense sintered bodies consisting of single-phase zinc gallate spinel were fabricated at 1100°C using zinc gallate spinel powders having almost stoichiometric composition formed from the solution at pH 9.95 in the presence of aqueous ammonia.     

YAG光学功能陶瓷材料

对日本研制的ＹＡＧ光学功能陶瓷的制备工、性能作了较详细的介绍。与过去的ＹＡＧ单晶陶瓷作了对比，并对其发展及应用前景进行了分析。     

钒钛磁铁精矿的烧结特性及强化措施

阐述了钒钛磁铁精矿的矿石特点，烧结特性及其与烧结矿质量之间的关系，并提出了强化烧结的措施。