Effect of PyC interface phase on the cyclic ablation resistance and flexural properties of two-dimensional Cf/HfC composites

Composites based on hafnium carbide and reinforced with continuous naked carbon fiber with and without PyC interface were prepared at low temperature by precursor infiltration and pyrolysis and chemical vapor deposition method. The microstructure, mechanical property, cyclic ablation and fiber bundle push-in tests of the composites were investigated. The results show that after three times ablation cycles, the bending strength of samples without PyC interface decreased by 63.6 %; the bending strength of samples with PyC interface only decreased by 37.8 %. The force displacement curve of the samples with PyC interface presented a well pseudoplastic deformation state. The mechanical behavior difference of two kinds of composites was due to crucial function of PyC interface phase including protection of fiber and weakening of fiber/matrix interface.     

加氢反应器头盖密封质量控制探讨

加氢反应器是加氢装置的重要组成部分,反应器头盖因工况复杂,导致密封难度较大,密封不严,会导致整个装置不能正常运转。为此,就其头盖拆装及密封问题进行探讨,提出有效的质量控制措施。     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法

提出了一种新的计算弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法，它是一种时域复模态分析方法。利用此方法获得了弹性-粘弹性复合结构在白噪声、滤过白噪声等典型平稳随机激励下随机响应的各阶谱矩的解析表达式，分析了粘弹性对各阶谱矩的影响。此计算方法简便、易用，无论单自由度或多自由度系统均适用，为进一步研究弹性-粘弹性复合结构在随机激励下的可靠性打下良好基础。     

STATIONARY TANGENT: THE DISCRETE AND NON-SMOOTH CASE

Abstract. In Keich (2000 ),we define a stationary tangent process, or a locally optimal stationary approximation, to a real non-stationary smooth Gaussian process. This paper extends the idea by constructing a discrete tangent – a `locally' optimal stationary approximation – for a discrete time, real Gaussian process. Analogously to the smooth case, our construction relies on a generalization of the recursion formula for the orthogonal polynomials of the spectral distribution function. More precisely, we use a generalization of the Schur parameters to identify the stationary tangent. By way of discretizing, we later demonstrate how this tangent can be used to obtain `good' local stationary approximations to non-smooth continuous time, real Gaussian processes. Further, we demonstrate how, analogously to the curvatures in the smooth case, the Schur parameters can be used to determine the order of stationarity of a non-smooth process.     

微带型Wilkinson功分器设计与实现

小型低功耗器件是射频电路设计的研究热点,而微带技术具有小型化低功耗的优点,为此在介绍微带型Wilkin-son功分器工作原理的基础上,使用基于矩量法的ADS软件设计、仿真和优化计算相关数据参数,并制作了一个微带功分器实例,最后对加工的样品进行实测,获得与仿真值吻合较好的预期结果。     

一种新型弹载偶极子天线分析与设计

给出了一种新型结构的弹载偶极子天线,采用基于自补结构的蛇形振子作为辐射器,并用矩量法对振子结构进行优化,采用简化形式的锥形BALUN以实现平衡馈电。测试结果表面该天线具有良好的E面全向特性和宽带特性。主要分析了该天线的辐射特性,最后给出并分析了实测数据。该天线具有结构紧凑、馈电简单、带宽较宽、易于制作等优点。