Phase composition,microstructure, and properties of Al4O4C–(Al2OC)1-x(AlN)x –Zr2Al3C4–Al2O3 refractories prepared at high temperatures in nitrogen

The novel Al₄O₄C–(Al₂OC)_1-x(AlN)_x–Zr₂Al₃C₄–Al₂O₃ refractories with ultra-low carbon content have been successfully prepared by constructing the core-shell structure of aluminum at 1300–1700°C in nitrogen. The phase composition, microstructure, and properties of the novel refractories are deeply investigated. The cracking temperature on the core-shell structure of aluminum is further explored and the reaction mechanism of Zr₂Al₃C₄ has also added explanation. The results show that the novel refractories have excellent physical properties and cannot be corroded by molten iron. There exist two different Al₂OC solid solutions in the novel refractories, Al₂OC-rich (Al₂OC)_1-x(AlN)_x and AlN-rich (Al₂OC)_1-x(AlN)_x. The temperatures affect their relative content. When temperatures are less than 1600°C, the relative content of Al₂OC-rich (Al₂OC)_1-x(AlN)_x is more than that of AlN-rich (Al₂OC)_1-x(AlN)_x. When temperatures are above 1700°C, the relative content of AlN-rich (Al₂OC)_1-x(AlN)_x is more than that of Al₂OC-rich (Al₂OC)_1-x(AlN)_x. The core-shell structure of aluminum fully ruptures at about 1200°C. Zr₂Al₃C₄ begins to form at about 1000°C and generates in large at 1200°C.     

The effect of particle size distribution on the microstructure and properties of Al2O3 ceramics formed by stereolithography

Stereolithography (SL) shows advantages for preparing alumina-based ceramics with complex structures. The effects of the particle size distribution, which strongly influence the sintering properties in ceramic SL, have not been systematically explored until now. Herein, the influence of the particle size distribution on SL-manufactured alumina ceramics was investigated, including bending strength at room temperature, post-sintering shrinkage, porosity, and microstructural morphology. Seven particle size distributions of alumina ceramics were studied (in μm/μm: 30/5, 20/3, 10/2, 5/2, 5/0.8, 3/0.5, and 2/0.3); a coarse:fine particle ratio of 6:4 was maintained. At the same sintering temperature, the degree of sintering was greater for finer particle sizes. The particle size distribution had a larger influence on flexural strength, porosity and shrinkage than sintering temperature when the particle size distribution difference reached 10-fold but was weaker for 10 μm/2 μm, 5 μm/2 μm and 5 μm/0.8 μm. The sintering shrinkage characteristics of cuboid samples with different particle sizes were studied. The use of coarse particles influenced the accuracy of small-scale samples. When the particle size was comparable to the sample width, such as 30 μm/5 μm and 5 mm, the width shrinkage was consistent with the height shrinkage. When the particle size was much smaller than the sample width, such as 2 μm/0.3 μm and 5 mm, the width shrinkage was consistent with the length shrinkage. The results of this study provide meaningful guidance for future research on applications of SL and precise control of alumina ceramics through particle gradation.     

水热法一步合成磷酸铁锂及其性能研究

为优化液相法一步制备磷酸铁锂（LiFePO₄）技术,以七水合硫酸亚铁、磷酸二氢铵、一水合氢氧化锂为原料,通过添加十二烷基苯磺酸钠（SDBS）作为表面活性剂,采用液相水热法合成技术,一步合成了LiFePO₄正极材料。研究了水热法一步合成技术对LiFePO₄材料的组成、结构、形貌、粒度等的影响,通过电感耦合等离子体发射光谱仪（ICP-OES）、X射线衍射仪（XRD）、扫描电镜（SEM）、粒度分析仪等对材料进行了表征分析,并测试了材料的电化学性能。研究结果表明,合成得到的LiFePO₄材料为微米级球形颗粒形貌的正交晶系非化学计量比的Li_1.02Fe_0.994PO₄材料。电化学性能测试结果表明,在0.1C倍率下首次充、放电比容量分别为162.0、159.9 mA·h/g,库伦效率达到98.7%、倍率性能（以1C/0.1C保持率计）为92.3%,0.1C倍率循环100次容量保持率为96.4%,展现出良好的电化学性能。     

Influence of ZrB2 hard ceramic reinforcement on mechanical and wear properties of aluminum

In this work, the effect of ZrB₂ (0, 5, 10 and 20?vol%) ceramic reinforcement on densification, structure, and properties of mechanically alloyed Al was investigated. The milling of Al-ZrB₂ powder compositions resulted in formation of agglomerates with varied size. In particular, the size of agglomerates was reduced considerably with increased addition of ZrB₂ to Al. Interestingly, the densification of hot pressed Al increased from 96.06% to 99.22% with ZrB₂ addition. The reduction of agglomerates size was attributed to the enhanced densification of Al-ZrB₂ composites. Pure Al showed relatively low hardness (0.94?GPa) and it was improved to 1.78?GPa with the addition of 20?vol% ZrB₂. The mechanical properties have significantly been improved for Al-ZrB₂ composites. Especially Al - 20?vol% ZrB₂ possessed a very high yield strength (529?MPa), compressive strength (630?MPa) and compressive strain of 19.25%. Realization of such a good combination of mechanical properties is the highest ever reported for Al composites so far in the literature. The coefficient of friction (COF) of Al-ZrB₂ varied narrowly between 0.33 and 0.40 after dry sliding wear against steel disc. The wear rate of Al-ZrB₂ composites was within mild wear regime and varied between 98.88?×?10^?6 and 34.66?×?10^?6 mm³/Nm. Among all the compositions, Al - 20?vol% ZrB₂ composite exhibited the lowest wear rate and high wear rate was noted for pure Al. Mild abrasion, tribo-oxidation, third body wear (wear debris) and delamination were the major material removal mechanisms for Al-ZrB₂ composites. Overall the hardness, strength and wear resistance of Al - 20?vol% ZrB₂ composite was improved by 84.3%, 84.3% and 64.2%, respectively when compared to pure Al.     

阴,阳离子聚合物地层内凝胶化改善水驱效果的研究

研究了一杆阴离子聚合物（Ａｃ５３０）和一种阳离子聚合物（Ｍｂ５８１）在水溶液中形成凝胶的条件和过程、凝胶化学结构、形态、稳定性和力学性能。在模拟地层的二维微观模型内观测了两种聚合物驱替渗流、相逼、形成凝胶、凝胶封堵大孔道的机理。在亲水填砂模型内测定了阴、阳离子聚合物凝胶体系降低渗透率的能力。     

Distribution of properties from sampling inhomogeneous materials by line transects

A theory related to the statistics of the structure and properties of inhomogeneous materials has been proposed, dealing with the distribution of properties from sampling of inhomogeneous structures by line transects. It is demonstrated that the empirical cumulative distribution functions of the intercepts from the microstructural constituents and their variances are important fingerprints of the inhomogeneous structures.Simulated sampling of the images of the microstructure by line transects has been proposed as a powerful method for characterization the distribution of properties of inhomogeneous structures. One of the advantages of the method based on the expected values of the order statistics of the intercepts is that the probability bounds of the property are determined without prior knowledge of the functional relationship between the property and the intercepts from the structural constituents.The concept intercept variance has an important application in determining the minimum transect length that stabilizes the variation of the intercept at a low value. Additionally, the concept ‘intercept variance’ can be used for topological optimization of the microstructure regarding the risk of intercepting a large amount of the weaker constituent. Equations regarding the variance of the intercepted fraction characterizing transect lengths with a specified distribution have also been derived.     

DCPD和PET合成不饱和聚酯的研究

探讨了用双环戊二烯和聚对苯二甲酸乙二醇酯废料合成不饱和聚酯树脂的方法：PET用二元醇醇解后，加入顺入烯二酸酐和DCPD，在80－120℃条件下滴加与DCPD等量的水进行反应，反应大约2.5h，加入其它成分，升温酯化直至反应完全。PET一定时，DCPD的含量影响不饱和聚酯同苯乙烯的互溶性和固化过程，DCPD和PET合成的不饱和聚酯树脂与标准树脂相比较，机械性能好，空干性好，解决了环境污染，具有很好的经济效益。     

试论融资租赁项下的进口贸易

阐述了当前跨国公司在合同中普遍采用的融资租赁的性质及融资租赁项下的进口贸易特点。     

废槽衬的性能研究

研究了废槽衬的外观形貌、微观结构、物相组成、元素含量,并对寿命相同的两种典型废槽衬的性能进行了对比分析,为选择废槽衬的无害化处理工艺提供了基础数据。