磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

郴州某复杂硫化铅锌矿阶段磨浮试验研究

针对郴州某复杂硫化铅锌矿资源的性质特点,采用铅快速浮选后尾矿再磨再选的阶磨阶选工艺,较好地实现了铅锌的高效浮选回收。研究了磨矿方式、捕收剂和调整剂种类及用量等因素对该矿石浮选的影响,确定了最佳浮选条件,通过小型闭路浮选试验,得到了铅品位60.05%、回收率89.63%的铅精矿和锌品位47.01%、回收率88.14%的锌精矿。     

PP－g－AA的制备和表征

用熔融接枝方法制备了聚丙烯－ｇ－丙烯酸（ＰＰ－ｇ－ＡＡ）。用光电子能谱，广角Ｘ射线衍射，红外光谱和化学滴定方法对接枝物进行了定性和定量表征。讨论了单体和引发剂浓度对接枝率的影响，确定了用红外光谱法测定接枝物含量的经验公式     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

轧辊磨床砂轮主轴的改进

介绍了安钢第二轧钢厂轧辊磨床砂轮主轴系统的改进与应用, 改进后磨床加工精度、工件表面粗糙度得到提高,降低了辊耗,提高了产品成材率和加工效率.     

潜孔锤冲击作用下土体变形的有限元分析

潜孔锤冲击挤密钻进过程中周围土体的变形机理是一个高度非线性问题。针对潜孔锤在土中的面-面接触问题,运用Drucker-Prager屈服准则为判据,将土体视为DP材料,通过钻具与土之间的接触及施加冲击载荷来模拟钻进过程,从而建立了潜孔锤在土中冲击挤密钻进的有限元模型。利用非线性瞬态动力学有限元分析手段,对钻进过程中冲击力对土的作用加以研究,分析了钻具周围土体的应力、应变以及钻具与土体的摩擦情况。结果表明,在冲击载荷作用下,锥形钻头前端土体应力集中,并形成应力泡,冲击功主要用于竖向压缩土体,而水平方向的挤压作用相对较小,摩擦应力在钻头锥面附近出现峰值,是影响钻进速度的主要原因之一。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。