Surface modification of poly(tetrafluoroethylene) and poly(ethylene terephthalate) films via environmental crazing

This work addresses the phenomenon of the development of a patterned surface relief on polymer films via different modes of environmental crazing. Commercial films of semicrystalline poly(tetrafluoroethylene) (PTFE) and amorphous glassy poly(ethylene terephthalate) (PET) were subjected to tensile drawing in the presence of physically active liquid environments (carbon tetrachloride or aliphatic alcohols). The structure parameters and wettability of the modified films were studied by AFM, SEM, profilometer measurements and contact angle measurements. Environmental intercrystallite crazing of PTFE is accompanied by the development of an unstable structure with a high free surface, which experiences marked strain recovery upon unloading. As a result of the relief formation, PTFE hydrophobicity is enhanced (the water contact angle increases by 25°). Classical environmental crazing of PET films is accompanied by the formation of an anisotropic surface relief which is an assembly of crazes oriented perpendicular to the direction of tensile drawing, thus leading to the phenomenon of anisotropic wetting. The proposed approach for structural surface modification makes it possible to use the advantages of surface instability and spontaneous self‐organization of the polymer towards the development of a unique surface microrelief. © 2020 Society of Chemical Industry     

Hydrogen wettability of clays: Implications for underground hydrogen storage

This study investigates the ability of hydrogen (H₂) to wet clay surfaces in the presence of brine, with implications for underground hydrogen storage in clay-containing reservoirs. Rather than measuring contact angles directly with hydrogen gas, a suite of other gases (carbon dioxide (CO₂), argon (Ar), nitrogen (N₂), and helium (He)) were employed in the gas-brine-clay system under storage conditions (moderate temperature (333 K) and high pressures (5, 10, 15, and 20 MPa)), characteristic of a subsurface environment with a shallow geothermal gradient. By virtue of analogies to H₂ and empirical correlations, wettabilities of hydrogen on three clay surfaces were mathematically derived and interpreted. The three clays were kaolinite, illite, and montmorillonite and represent 1:1, 2:1 non-expansive, and 2:1 expansive clay groups, respectively. All clays showed water-wetting behaviour with contact angles below 40° under all experimental set-ups. It follows that the presence of clays in the reservoir (or caprock) is conducive to capillary and/or residual trapping of the gas. Another positive inference is that any tested gas, particularly nitrogen, is suitable as cushion gas to maintain formation pressure during hydrogen storage because they all turned out to be more gas-wetting than hydrogen on the clay surfaces; this allows easier displacement and/or retrieval of hydrogen during injection/production. One downside of the predominant water wettability of the clays is the upstaged role of biogeochemical reactions at the wetted brine-clay/silicate interface and their potential to affect porosity and permeability. Water-wetting decreased from kaolinite as most water-wetting clay over illite to montmorillonite as most hydrogen-wetting clay. Their wetting behaviour is consistent with molecular dynamic modelling that establishes that the accessible basal plane of kaolinite's octahedral sheet is highly hydrophilic and enables strong hydrogen bonds whereas the same octahedral sheet in illite and montmorillonite is not accessible to the brine, rendering these clays less water-wetting.     

油藏中分散非连续残余油膜的驱替机理分析

水驱后的残余油膜将贴于孔隙壁面，为壁面边界层流体，处于三相界面的包围和共同作用下。目前的调研结果显示，油膜的组成及力学特性沿孔壁方向上是变化的。在化学驱过程中油膜不仅受到驱油剂的驱替作用。还受驱油剂／油界面张力、油／固体界面张力及驱油剂／固体界面张力的阻碍作用。由于油膜组成、力学特性及相间作用的复杂性．以往对油膜驱替机理的研究都是从微观实验的角度对现象作观察和定性解释。本文根据水驱后残余油膜在油藏孔隙中存在的特点，提出了油膜驱替的简化模型。基于油膜驱替的微观实验，采用数值方法从定量的角度分别计算了不同黏弹性驱油剂在不同的驱油剂／原油界面张力作用下对残余油膜的驱替效率。考察了驱油剂的流变性、驱油剂／油界面张力、驱替速度等因素对驱替不同厚度油膜的影响规律。进一步探讨了驱油剂／原油界面特性和流变性在驱替残余油中的综合作用。研究结果表明，驱油剂对油膜的驱替始于驱油剂／油界面，要同时克服驱油剂／油界面约束力和油膜的屈服应力。降低界面张力、增强驱油剂的黏弹性、增加驱替速度，有利于提高驱替残余油膜的驱替效率。适当增加驱油刑的黏弹性可以放宽驱替薄油膜时对超低界面张力的要求。图13参9。     

注水吞吐开发低渗透裂缝油藏探讨

室内油层岩心驱替实验研究结果表明，注水吞吐采油技术可发挥油层毛管力吸水排油作用，实现水驱，能有效地补充地层能量，恢复地层压力。通过多周期的注水吞吐开发，逐渐扩大水驱波厦半径，提高驱替效率。油层润湿性和渗透率是影响注水吞吐开发效果的主要因素。该技术简单易行，在头台油田实施后，效果十分显著，对同类油藏的开发真有指导意义。     

高温酸化助排剂HC2-1的研究

为了满足高温油藏和深井酸化作业残酸返排的需要，通过表面活性剂的筛选和复配研究，得到了高温酸化助排剂HC2—1。其性能评价结果表明，HC2—1具有使用浓度低、表面活性高的特点，在20％的HCI溶液中，当其浓度为50mg／L时，表面张力为20．7mN／m；具有良好的耐温性能，在180℃下恒温48h，HC2—1仍保持较高的表面活性；具有良好的耐盐能力，加有HC2—1的20％HCl溶液和CaCO3反应至HCl完全消耗，整个反应过程体系无新相生成且表面张力基本不变；可增大酸液体系的润湿角，进一步降低毛细管阻力，使酸液返排率由46％提高到97％，在促进酸液返排的同时与原油不发生乳化反应。     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Forecasting Capillary Characteristics for Aluminum Nitride Ceramic ― Liquid Metal Systems

A test has been devised that allows one to determine the work of adhesion and wettability in a system composed of aluminum nitride ceramics with a liquid metal without the need for experimental examination. A correlation is examined between the work of adhesion on the one hand and that criteria or others on the other that have been proposed by various researchers. Forecasts are made for the work of adhesion and wetting angle for a series of metals that have not been examined previously. An experimental check has been made on the forecast adhesion activity for some elements.