Metal chlorides-promoted ammonia absorption of deep eutectic solvent

Ammonia is considered as a promising hydrogen or energy carrier. Ammonia absorption or adsorption is an important aspect for both ammonia removal, storage and separation applications. To these ends, a wide range of solid and liquid sorbents have been investigated. Among these, the deep eutectic solvent (DES) is emerging as a promising class of ammonia absorbers. Herein, we report a novel type of DES, i.e., metal-containing DESs for ammonia absorption. Specifically, the NH₃ absorption capacity is enhanced by ca. 18.1–36.9% when a small amount of metal chlorides, such as MgCl₂, MnCl₂ etc., are added into a DES composed of resorcinol (Res) and ethylene glycol (EG). To our knowledge, the MgCl₂/Res/EG (0.1:1:2) DES outperforms most of the reported DESs. The excellent NH₃ absorption performances of metal–containing DESs have been attributed to the synergy of Lewis acid–base and hydrogen bonding interactions. Additionally, good reversibility and high NH₃/CO₂ selectivity are achieved over the MgCl₂/Res/EG (0.1:1:2) DES, which enables it to be a potential NH₃ absorber for further investigations.     

不同管距时玉米渗灌效果的试验研究

在运城市夹马口灌区和红旗灌区进行了1996,1997两个年度的玉米渗灌试验,研究了不同毛管间距条件下渗灌对其产量及水分生产率等的影响。结果表明,玉米渗灌毛管间距采用0.8~1.0 m较为适宜。毛管间距愈大,产量愈低;渗灌较地面灌平均减产7.23%,较旱地平均增产30.8%;玉米生长期内总耗水量地面灌最大,渗灌次之,旱地最小。渗灌可明显提高玉米水分生产率,渗灌处理水分生产率平均为1.65 kg/m3,是地面灌的1.2倍,是旱地的1.33倍;两年度渗灌较地面灌平均节水44.4%。     

小井距开发现河油田低渗油藏可行性研究

认为注采井网井距大,水驱控制程度差,采收率偏低是影响胜利油田现河低渗透油藏开发的关键,通过井间密度与水驱控制程度和采收率的关系等分析,提出了现河低渗透油藏开发的合理的井网密度。     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

低渗透油田合理注采井距的确定--以纯41块沙4段低渗透油田为例

以纯41块沙4段低渗透油田为例，从低渗透油田渗流机理出发，分析了造成低渗透油田开发效果差的主要原因。在计算注水井最大井底流压、油井最小井底流压、油水井之间可建立的最大注采压差的基础上，结合室内试验确定的最小启动压力梯度公式计算油田技术极限注采井距，并结合经济合理井距计算结果，确定了油田合理注采井距，并提出了下二步调整方案，实施后取得了显著的效果。该方法为低渗透油田合理井距的确定、提高低渗透油田的开发效果提供了理论依据。     

C／O测井响应随源距变化的理论研究

针对井内介质分别为水、油，地层分别为３５％孔隙度饱和水砂和油砂的４种情况，采用蒙特卡罗方法模拟外径φ８９碳氧比测井仪不同源距处的非弹性散射伽马能谱。通过分析地层或井内介质不同时的Ｃ／Ｏ差值随源距变化的关系，为设计仪器推荐源距参数。     

一种高温蓄冷介质蓄放冷特性的应用研究

采用实验的方法获得了氯酸锂共晶盐的蓄放冷特性的实用关系式。这种介质的融点为８℃，单位体积蓄冷量比冰大３０％，适于用作空调系统中的蓄冷材料。     

Determination of Discrete-Structure Parameters of Coatings with Allowance for Residual Stresses

The authors suggest that the dimensions of a discrete section of a coating should be chosen on the basis of calculation of the critical crack spacing in cohesion cracking. This approach allows for residual stresses in the coating. The reliability of the calculation method has been verified experimentally by direct measurement of the crack spacing.     

Phase equilibria in the system Al-Rh

Methods of differential thermal analysis, x-ray diffraction, microstructural analysis and electron probe microanalysis are used to study alloys of the Al-Rh system over the whole concentration range. It is established that the phase of equiatomic composition AlRh melts congruently at 2060°C and it has an extended range of homogeneity (45.1–54.2 at.% Rh). The solubility of aluminum in rhodium reaches 9 at.%, decreasing to 6 at.% at 850°C. Coordinates are determined for the eutectic point l ⇆ AlRh + 〈Rh〉 as 70 at.% Rh and 1715°C. The existence of intermediate phases, their crystal structure, and also the method of forming phases in the field of composition rich in aluminum given in publications are confirmed. __________ Translated from Poroshkovaya Metallurgiya, Nos. 5–6(449), pp. 48–56, May–June, 2006.