Impact behavior and fractographic study of carbon nanotubes grafted carbon fiber-reinforced epoxy matrix multi-scale hybrid composites

Carbon nanotubes are the most promising reinforcement for high performance composites. Multiwall carbon nanotubes were directly grown onto the carbon fiber surface by catalytic thermal chemical vapor deposition technique. Multi-scale hybrid composites were fabricated using the carbon nanotubes grown fibers with epoxy matrix. Morphology of the grown carbon nanotubes was investigated using field emission scanning electron microscopy and transmission electron microscopy. The fabricated composites were subjected to impact tests which showed 48.7% and 42.2% higher energy absorption in Charpy and Izod impact tests respectively. Fractographic analysis of the impact tested specimens revealed the presence of carbon nanotubes both at the fiber surface and within the matrix which explained the reason for improved energy absorption capability of these composites. Carbon nanotubes presence at various cracks formed during loading provided a direct evidence of micro crack bridging. Thus the enhanced fracture strength of these composites is attributed to stronger fiber–matrix interfacial bonding and simultaneous matrix strengthening due to the grown carbon nanotubes.     

基于α-FeOOH催化H2O2蒸气的低温烟气脱硝实验

针铁矿是分布广泛、储量丰富的铁氧化物，其主要成分为α-羟基氧化铁（α-FeOOH）。为了探究针铁矿在催化H₂O₂烟气脱硝反应中的性能，本文通过沉淀-水解法制备了α-FeOOH，并在自行搭建的实验台上开展了α-FeOOH催化H₂O₂的低温烟气脱硝实验研究，深入分析了H₂O₂流量、H₂O₂浓度、汽化温度、反应温度和共存气体浓度等工况参数对脱硝性能的影响。采用离子色谱（IC）分析了单独脱硝反应和同时脱硫脱硝反应后的含氧酸成分，结合各项表征分析技术考察了催化剂反应前后的理化特性和稳定性。实验结果显示，随着汽化温度和反应温度的升高，NO的脱除效率先增加后降低；增加H₂O₂浓度对脱硝效率有明显的促进作用。当汽化温度为140℃、反应温度为160℃时，以2.5mL/h注入10mol/L的H₂O₂脱硝效率达到80%。当SO₂浓度为1000μL/L时，脱硝效率提高至86.4%。离子色谱分析结果显示，单独脱硝反应和同时脱硫脱硝反应后含氧酸产物为HNO₃和H₂SO₄。反应前后催化剂的表征结果显示，α-FeOOH在脱硝反应后依然具有良好的稳定性，显示出针铁矿在低温烟气脱硝工艺中的潜在应用前景。     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Hydrogen from wet air and sunlight in a tandem photoelectrochemical cell

A solid-state photoelectrochemical (SSPEC) cell is an attractive approach for solar water splitting, especially when it comes to monolithic device design. In a SSPEC cell the electrodes distance is minimized, while the use of polymer-based membranes alleviates the need for liquid electrolytes, and at the same time they can separate the anode from the cathode. In this work, we have made and tested, firstly, a SSPEC cell with a Pt/C electrocatalyst as the cathode electrode, under purely gaseous conditions. The anode was supplied with air of 80% relative humidity (RH) and the cathode with argon. Secondly, we replaced the Pt/C cathode with a photocathode consisting of 2D photocatalytic g-C₃N₄, which was placed in tandem with the photoanode (tandem-SSPEC). The tandem configuration showed a three-fold enhancement in the obtained photovoltage and a steady-state photocurrent density. The mechanism of operation is discussed in view of recent advances in surface proton conduction in absorbed water layers. The presented SSPEC cell is based on earth-abundant materials and provides a way towards systems of artificial photosynthesis, especially for areas where water sources are scarce and electrical grid infrastructure is limited or nonexistent. The only requirements to make hydrogen are humidity and sunlight.     

Development of mobile miniature natural gas liquefiers

With increasing consumption of natural gas (NG), small NG reservoirs, such as coalbed methane and oil field associated gas, have recently drawn significant attention. Owing to their special characteristics (e.g., scattered distribution and small output), small-scale NG liquefiers are highly required. Similarly, the mixed refrigerant cycle (MRC) is suitable for small-scale liquefaction systems due to its moderate complexity and power consumption. In consideration of the above, this paper reviews the development of mobile miniature NG liquefiers in Technical Institute of Physics and Chemistry (TIPC), China. To effectively liquefy the scattered NG and overcome the drawbacks of existing technologies, three main improvements, i.e., low-pressure MRC process driven by oil-lubricated screw compressor, compact cold box with the new designed heat exchangers, and standardized equipment manufacturing and integrated process technology have been made. The development pattern of “rapid cluster application and flexible liquefaction center” has been eventually proposed. The small-scale NG liquefier developed by TIPC has reached a minimum liquefaction power consumption of about 0.35 kW·h/Nm³. It is suitable to exploit small remote gas reserves which can also be used in boil-off gas reliquefaction and distributed peak-shaving of pipe networks.     

PECVD法低温沉积多晶硅薄膜的研究

在玻璃衬底上采用常规的PKCVD法在低温(≤400℃)条件下制得大颗较(直径＞100nm)、择优取向(220)明显的多晶硅薄膜。选用的反应气体为SiF4和H2混合气体。加入少量的SiH4后，沉积速率提高了近10倍。分析认为，在低温时促使多晶硅结构形成的反应基元应是SiFmHn(m n≤3)，而不可能是SiHn(n≤3)基团。     

流量比对等离子体基团分布和薄膜结构的影响

使用光强标定的发射光谱(AOES)测量了CHF3／C6H6混合气体的微波电子回旋共振(ECR)放电等离子体中基团的分布状态。实验发现随着CHF3流量的增加，成膜基团CF、CF2、CH等的相对密度增大，而刻蚀基团F的密度也会增加，从而使得a—C：F薄膜的沉积速率降低。同时红外吸收谱(IR)分析表明，在高CHF3流量下沉积的a—C：F薄膜中含有更高的C—F键成分。可见在a—C：F薄膜的制备中CHF3／(CHF3 C6H6)流量比是重要的控制参量。     

铜蒸气激光器种子注入光腔的参数计算

用矩阵光学理论计算了由主振荡器和功率放大器组成的种子注入光腔。主振荡器光腔是由曲率半径R1=-250mm,R2=5000mm,相距L=2375mm的球面镜组成的正支非稳腔;功率非稳腔是由曲率半径R3=400mm,R4=5600mm,相距S=3000mm的球面镜构成的负支非稳腔。理论计算表明,该种子注入光腔可输出光束发散角约几十微弧的激光,可满足铜蒸气激光器主振荡器功率放大器(MOPA)的技术要求。