A knowledge-based archive multi-objective simulated annealing algorithm to optimize series–parallel system with choice of redundancy strategies

Redundancy allocation problem (RAP) is one of the best-developed problems in reliability engineering studies. This problem follows to optimize the reliability of a system containing s sub-systems under different constraints, including cost, weight, and volume restrictions using redundant components for each sub-system. Various solving methodologies have been used to optimize this problem, including exact, heuristic, and meta-heuristic algorithms. In this paper, an efficient multi-objective meta-heuristic algorithm based on simulated annealing (SA) is developed to solve multi-objective RAP (MORAP). This algorithm is knowledge-based archive multi-objective simulated annealing (KBAMOSA). KBAMOSA applies a memory matrix to reinforce the neighborhood structure to achieve better quality solutions. The results analysis and comparisons demonstrate the performance of the proposed algorithm for solving MORAP.     

表面活性剂对低渗透油藏渗吸的影响

采用不同类型的表面活性剂进行自发渗吸实验,并对表面活性剂改善岩石润湿性、降低界面张力的能力进行了分析。实验结果表明,阴离子型表面活性剂改善润湿性的能力好于其他类型的表面活性剂,且在岩心中的自发渗吸效果最好,这是由于阴离子型表面活性剂改善润湿性的机理为离子对形成机理,强于阳离子的吸附机理;接触角是决定渗吸能否发生的决定性因素,只有接触角小于70°时渗吸才能发生;界面张力影响渗吸速度和最终采出程度,对于渗透率为1 mD的岩心,最佳界面张力为10~(-1) mN/m。     

Strain hardening behaviors and mechanisms of polyurethane under various strain rate loading

The uniaxial tension experiments are performed on thermoplastic polyurethane to investigate its mechanical behaviors and related potential mechanisms, and the loading strain rate is designing to be wide ranging from 0.0001 to 1 s⁻¹. It is found that the polyurethane presents an obvious rate-dependence, and the stress strain curves share distinct strain hardening characteristics under the investigated strain rates. Furthermore, the strain hardening ratios are sharing nearly same trends and appear to be influenced by both strain rate and the induced adiabatic heating. Besides, the ratio is also strain-dependent on previous loading history. Then, a two-dimension unit cell model is built to investigate potential equivalent mechanisms, of which the hard phase as inclusion is equivalent with crystallization zone, crosslinking sites, and so forth. The simulation results facilitate to explain the distinct strain hardening ratios, even for the matrix from the extrapolated curves under super-low strain rate loading. Finally, the analogic mechanisms of equivalent hard inclusions are proposed, which can reasonably explain the strain rate- and strain-dependence characteristics of polyurethane mechanical behaviors.     

Ca2+ doping effects on the structural and electrical properties of Na0.5Bi4.5Ti4O15 piezoceramics

Bismuth layer structured Na_0.5Bi_4.5Ti₄O₁₅ (NBT) ferroelectric is one of the most promising materials for potential applications at high temperature. However, it is challenged to achieve a balance between high Curie temperature piezoelectric coefficient and excellent thermal stability for NBT piezoceramics. Here, through chemical modification at the A site of NBT with Ca²⁺, novel (Na_0.5Bi_0.5)_1-xCa_xBi₄Ti₄O₁₅ piezoceramics with excellent properties fabricated by solid state reaction were studied. After doping of Ca²⁺, the Curie temperature T_C increased from 648 °C to 662 °C while the piezoelectric coefficient d₃₃ increased from 14 pC/N to 22 pC/N which can be attributed to the intrinsic contribution of TiO₆ octahedral lattice distortion (tilting and rotation) and the extrinsic contribution of the increased density of domain walls. The composition of (Na_0.5Bi_0.5)_0.95Ca_0.05Bi₄Ti₄O₁₅ ceramics with x = 0.05 has the optimal performance with high T_C of 655 °C, large d₃₃ of 22 pC/N, high electrical resistivity ρ close to 10⁷ Ω cm at 500 °C and especially excellent thermal stability of d₃₃ only about 5% reduction after being annealed at 625 °C. The work effectively reveals the great potential of CNBT-5 ceramics for high-temperature piezoelectric applications.     

罩式退火温度对高强IF钢组织及性能的影响

为研究不同退火温度下高强IF钢的组织性能及织构的变化规律,采用温箱式电阻炉加热模拟罩式退火工艺,研究了不同退火温度下高强IF钢210P1冷轧板力学性能;对不同退火温度钢板的r90进行了统计并对其进行显微组织观察;采用X射线衍射仪及热场发射扫描电镜对不同退火温度的罩式退火成品板进行了织构分析。结果表明,在高强IF钢210P1冷轧板的罩式退火过程中,提高退火温度将使晶粒明显长大。随着退火温度的升高,屈服强度及抗拉强度下降,伸长率升高,n值略有上升,板材横向r值增加较明显,有利织构{111}取向密度增加,不利织构{100}取向密度降低。     

Biodegradability Study of the Biosurfactant Contained in a Crude Extract from Corn Steep Water

Over the last few years, the global biosurfactant market has raised due to the increasing awareness among consumers, for the use of biological or bio-based products. Because of their composition, it can be speculated that these are more biocompatible and more biodegradable than their chemical homologous. However, at the moment, no studies exist in the literature about the biodegradability of biosurfactants. In this work, a biosurfactant contained in a crude extract, obtained from a corn wet-milling industry stream that ferments spontaneously in the presence of lactic acid bacteria, was subjected to a biodegradation study, without addition of external microbial biomass, under different conditions of temperature (5–45 °C), biodegradation time (15–55 days), and pH (5–7). For that, a Box–Behnken factorial design was applied, which allowed to predict the percentage of biodegradation for the biosurfactant contained in the crude extract, between the range of the independent variables selected in the study, obtaining biodegradation values between 3 and 80%. The percentage of biodegradation for the biosurfactant was calculated based on the increase in the surface tension of samples of the crude extract. Furthermore, it was also possible to predict the variation in t_1/2 for the biosurfactant (time to achieve the 50% of biodegradation) under different conditions.     

Damage mechanism at different transpassive potentials of solution-annealed 316 and 316l stainless steels

Electrochemical impedance spectroscopy (EIS), anodic polarization and scanning electron microscopy techniques were used to investigate the damage mechanism in the transpassive potential region of AISI ...     

釉面分相对无铅CuO-MnO2系金属光泽釉的影响

以钙系生料釉为基础,引入结晶剂CuO、MnO₂制备无铅CuO-MnO₂系金属光泽釉;结合XRD、SEM-EDS进行物相组成定性分析和显微结构表征,系统探究外加TiO₂、V₂O₅以及玻璃粉对金属光泽釉釉面分相的影响。研究表明:一定量的TiO₂、V₂O₅引入能有效促进釉面的分相,将玻璃粉部分替换基础釉中的钾长石能使得釉熔体的高温粘度降低,并进一步加剧釉面分相,促进CuMn₂O₄铜锰尖晶石在釉层表面的析出和富集;当TiO₂引入量为2%,V₂O₅引入量为1%,玻璃粉引入量为25%(同为质量分数)时,金属光泽釉釉面效果最佳。     

Enhancement of optical and electrical properties of SILAR deposited ZnO thin films through fluorine doping and vacuum annealing for photovoltaic applications

Undoped and fluorine doped ZnO thin films were deposited onto glass substrates using successive ionic layer adsorption and reaction (SILAR) technique and then annealed at 350 °C in vacuum ambience. The F doping level was varied from 0 to 15 at% in steps of 5 at%. The XRD analysis showed that all the films are polycrystalline with hexagonal wurtzite structure and preferentially oriented along the (002) plane. Crystallite sizes were found to increase when 5 at% of F is doped and then decreased with further doping. It was seen from the SEM images that the doping causes remarkable changes in the surface morphology and the annealing treatment results in well-defined grains with an improvement in the grain size irrespective of doping level. All the films exhibit good transparency (>70%) after vacuum annealing. Electrical resistivity of the film was found to be minimum (1.32×10⁻³ Ω cm) when the fluorine doping level was 5 at%.