Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

Wavelength and Waveband Assignment for Ring Networks Based on Parallel Multi‐granularity Hierarchical OADMs

In this paper we study the optimization issues of ring networks employing novel parallel multi‐granularity hierarchical optical add‐drop multiplexers (OADMs). In particular, we attempt to minimize the number of control elements for the off‐line case. We present an integer linear programming formulation to obtain the lower bound in optimization, and propose an efficient heuristic algorithm called global bandwidth resource assignment that is suitable for the design of large‐scale OADM networks.     

光传送网中的关键光器件

光器件是光传送网的基础单元之一，本主要综述光传送网中的关键光器件：光源与光探测器、光波分复用/解复用器、光放大器、色度色散与偏振模补偿器及光开关等。比较了各种光器件的主要技术方案，特别针对的是已实用化的技术方案。最后讨论了光器件的尺寸小型化、微型化以及多功能集成等发展趋势，介绍了光器件的集成方式如：传统分立光器件的集成，平面光波导集成，以及混合集成等。     

光纤光栅在传感应用中波长漂移的检测方案

波长漂移量的检测是实现光纤光栅传感网络的关键技术。分类阐述了近几年来光纤光栅传感应用中主要的波长检测方案,分析了它们的工作机理和特性,并展望了其可观的应用前景。     

基于谐振原理的硅微机械加速度计

基于力学振动原理 ,导出敏感梁类谐振振动的微分方程 ,给出了振梁型加速度计的设计原理。指出了加速度计谐振梁频率的相对变化量与梁的厚度无关 ;为避免输出非线性频率信号 ,频率的相对变化率和激励振动的振幅都不宜太大     

基于均匀光纤光栅的DWDM系统PMD补偿方法

提出一种基于均匀光纤Bragg光栅(FBG)的透射型密集波分复用(DWDM)系统多信道偏振模色散(PMD)补偿方案。当FBG受到横向挤压时，会产生双折射现象。当一波长的光信号从光栅带隙附近透射时，就会在快轴和慢轴之间产生时延差(DGD)。通过改变外力的大小来调节DGD的大小可以实现对PMD的补偿。通过将多个补偿光栅级联，就可以实现对DWDM系统多信道PMD的补偿。在100N外力作用下，5cm长的光栅最大可以补偿121ps的PMD，而对相邻0．8nm的信道，只引入0．2ps的DGD。     

微机械可调谐滤波器的研制

利用 Ga As/Al Ga As分布反馈 Bragg反射镜在 Ga As衬底上制作了一个微机械的调谐滤波器 .该器件在 7V调谐电压下调谐范围达28nm     

双波长稳频CO_2激光模糊控制系统的建模与优化

报导一种模糊逻辑控制系统的建模与优化方法。以此方法设计的模糊逻辑控制器，用于双波长稳频ＣＯ２激光器的控制得到令人满意的结果。     

基于体全息技术的WDM器件

利用体全息技术制作波分复用器件是一种新方法。本文介绍了此种方法的基本原理和器件的基本性能，并报道了国外对该项技术的研究进展。