激光在材料中感生的瞬态光声波和光热波

研究了锁模激光在材料中产生频率达GHz的光声波和相应探测技术,用回波分析法无损坏测量了薄材料的厚度。研究了激光在材料中感生的光热波,热沉测量可用于解释材料的破坏机理。     

L波段窄脉宽500W固态功放组件的设计

介绍了作者研制的应用于固态雷达发射机上的L波段500W固态功放组件的工作原理、用途及其主要技术指标。描述了功放组件的设计过程和测试结果。该功放组件在窄脉宽条件下实现了快速上升沿,性能优良,工作稳定可靠。     

氮离子注入尼龙1010的摩擦学特性

用高能离子注入机对尼龙 10 10进行 N+注入改性 ,注入能量为 4 5 0 ke V,剂量分别为 5× 10 14 /cm2 、2 .5× 10 15/cm2 及 1.2 5× 10 16/cm2 。以 Zr O2 及 Si3N4 球为上球样 ,分别与注入尼龙 10 10下盘样组成摩擦副 ,在销盘摩擦试验机上评价它们在干摩擦条件下的摩擦磨损行为。结果表明 ,几种剂量的 N+注入均增强了尼龙 10 10的耐磨性。未注入样品的磨损主要表现为粘着、塑性变形、犁沟和疲劳脱层 ,注入样品的磨损主要为轻微的磨粒磨损。     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Dispersion characterization in layered double hydroxide/Nylon 66 nanocomposites using FIB imaging

Layered double hydroxides (LDHs), a newly emerging 2D host material, consist of cationic brucite-like layers and exchangeable interlayer anions. In this work, the morphology and dispersion of LDH particles in LDH/Nylon 66 (salt) nanocomposites has been investigated using focused ion beam (FIB) techniques, transmission electron microscopy (TEM) and X-ray diffraction (XRD). The FIB images show that LDHs are present in the polymer phase dispersed to different degrees, with partial intercalation, exfoliation, and aggregation all being observed. The most even dispersion was achieved in nanocomposites with the lowest loading (0.5 wt % LDH). Residual tactoids and agglomerates were most common in the samples made with the highest concentration of LDHs studied here (5 wt %). The dispersion observed using FIB was consistent with TEM and XRD analysis, yet this technique had significant benefits in terms of time and simplicity over these “conventional” technologies. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study of the effective parameters on mechanical and electrical properties of carbon black filled PP/PA6 microfibrillar composites

In this study the electrical and mechanical properties of microfibrillar polypropylene (PP)/polyamide6 (PA6) blend filled with super conductive carbon black (CB) have been investigated. In situ microfibrillar PP/PA6 composites filled with CB are produced using a single screw extruder equipped with a spinneret. Glycidyl methacrylate (GMA) grafted polypropylene (PP-g-GMA) is used as the compatibilizer. To investigate the effects of extensional flow on the microstructure, electrical and mechanical properties, three adaptors with various convergence angles were designed, prepared and applied between the extruder and the spinneret. To optimize the effects of processing and material parameters on the electrical and mechanical properties, the Taguchi method of experimental design is used. Material and processing factors which are studied include: concentration of PA6, compatibilizer level, CB concentration, drawing speed of melt spinning line, adaptor angle, order of mixing and temperature profile along the extruder. The results show an increase in DC conductivity of up to 10¹¹ times in comparison with pure PA6, by increasing the concentration of CB, drawing speed, adaptor angle and optimizing other parameters. By optimizing processing and material factors studied here, strength of microfibrillar structured composites is increased of up to 80% in comparison to pure PP.     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

PA6－PEG共聚纤维和PA6－PEG／PA6共混纤维的物理与力学性能

研究了ＰＡ６－ＰＥＧ共聚纤维以及不同组成比的ＰＡ６－ＰＥＧ／ＰＡ６共混纤维的各项性能。得到了平衡吸湿率可达８％左右的改性纤维。纤维的染色性和手感也有显著改善，力学性能可满足纺织加工的要求。     

增强增韧尼龙66工程塑料流变行为的研究

对以合金化技术改性所得增强增韧尼龙６６进行流变行为研究的结果表明，填充玻纤，可使其增强，但使流动性能下降：共混接枝聚丙烯，可使其增韧，并改善加工流动性，填充超细滑石粉，除有一定增强作用外，也使加工流动性，制品表面光滑程度和尺寸稳定性得到改善。填充共混的协同作用使改性尼龙６６有较好的综合性能。     

空间激光通信系统精跟踪单元PZT驱动电源的设计

压电陶瓷驱动电源是压电陶瓷微位移器应用中的关键部件。PA85是一种高电压、高功率MOSFET的带宽运算放大器,采用双电源供电,输出电流高达200mA,输出电压更可高达±215V。该文详细介绍了基于PA85的一种电源复合放大器的设计及仿真,通过对各项性能指标的仿真表明,该驱动电源具有精度高、分辨率高、稳定性好、纹波小和电路结构简单等优点。