全文获取类型
收费全文 | 1460篇 |
免费 | 93篇 |
国内免费 | 58篇 |
专业分类
电工技术 | 65篇 |
综合类 | 121篇 |
化学工业 | 90篇 |
金属工艺 | 182篇 |
机械仪表 | 137篇 |
建筑科学 | 216篇 |
矿业工程 | 241篇 |
能源动力 | 54篇 |
轻工业 | 25篇 |
水利工程 | 185篇 |
石油天然气 | 78篇 |
武器工业 | 11篇 |
无线电 | 10篇 |
一般工业技术 | 83篇 |
冶金工业 | 67篇 |
原子能技术 | 19篇 |
自动化技术 | 27篇 |
出版年
2024年 | 4篇 |
2023年 | 19篇 |
2022年 | 24篇 |
2021年 | 37篇 |
2020年 | 38篇 |
2019年 | 20篇 |
2018年 | 13篇 |
2017年 | 41篇 |
2016年 | 58篇 |
2015年 | 51篇 |
2014年 | 88篇 |
2013年 | 88篇 |
2012年 | 114篇 |
2011年 | 110篇 |
2010年 | 70篇 |
2009年 | 101篇 |
2008年 | 72篇 |
2007年 | 84篇 |
2006年 | 71篇 |
2005年 | 68篇 |
2004年 | 60篇 |
2003年 | 68篇 |
2002年 | 60篇 |
2001年 | 39篇 |
2000年 | 48篇 |
1999年 | 27篇 |
1998年 | 28篇 |
1997年 | 18篇 |
1996年 | 24篇 |
1995年 | 17篇 |
1994年 | 8篇 |
1993年 | 8篇 |
1992年 | 7篇 |
1991年 | 13篇 |
1990年 | 5篇 |
1989年 | 4篇 |
1988年 | 2篇 |
1987年 | 3篇 |
1954年 | 1篇 |
排序方式: 共有1611条查询结果,搜索用时 15 毫秒
1.
Objectives of this study are to analyze the HAV exposures of chipping hammer operators from field measurements and to investigate the potential of various types of gloves in reducing the exposures. HAV exposures of twelve male operators were measured at four different operating conditions: bare hand, wearing normal workman gloves, wearing heavy workman gloves and wearing vibration reducing gloves. From the measurements, 8 h exposure values were determined and assessed against standards. The total vibration values were determined and effectiveness in vibration attenuation by gloves was compared. It was found that all most all operators, HAV exposure levels exceeded the exposure action value (EAV) and about 83% of the operators exceeded the exposure limit values (ELV). A reduction in the total vibration magnitude was observed with protective gloves: 8.3% with normal workman gloves, 14.6% with heavy workman gloves and 40% with vibration-reducing gloves. To confirm the effectiveness of the vibration reducing gloves, further field investigations are required with simultaneous measurements by considering parameters affecting HAV (i.e., hand forces and postures). 相似文献
2.
3.
大采高液压支架供液管路的工作压力为23~32.5 MPa、通流直径为38~60 mm、管路长度为1 000~1 500 m,供液管路具有明显压力、流量响应滞后效应,导致立柱缸液压系统的速度、位移动态特性较差。对液压支架大通径高压供液管路进行水锤试验,试验结果为:在流量为182.7、351.2和521.5 L/min时,压力波速分别为715、979和1 065 m/s。建立了AMESim管路模型和液压支架系统模型,分析管路长度、管路通径和初始压力对液压支架立柱动态特性影响规律。仿真结果表明:管路长度越大,管路通径越大,管路初始压力越小,立柱响应时间越长,升柱和降柱过程平稳性高,所用时间增长。 相似文献
4.
5.
6.
抗滑表层沥青混合料试验参数研究 总被引:2,自引:0,他引:2
针对近年来沥青路面抗滑表层混合料在生产中暴露出来的耐久性差、抗滑能力不持久等问题 ,认为不能简单的对这一级配形式予以否定 ,并尝试通过对其击实次数、空隙率指标等关键试验参数进行调整以改善其路用性能。在理论分析与试验研究的基础上 ,提出在抗滑表层混合料配合比设计中 ,将规范要求的马歇尔试件双面 5 0次击实改为 75次 ,同时相应降低空隙率要求 ,对保持路面抗滑性能与耐久性能之间的平衡、提高混合料的各项路用性能具有重要的意义 相似文献
7.
分析了传统加压泵房配置存在的弊端 ,并就新型水力控制阀门的功能特点 ,从安装方法、工作原因等方面作了阐述 ,展望了该产品广阔的应用前景 相似文献
8.
9.
10.
山东莱芜钢铁集团有限公司特殊钢厂的供水主管路属于典型的山区长距离、高扬程输水系统。在供水系统改造中将管路由埋地方式改为架空敷设,由四级供水改为两级供水,并特别考虑了停泵水锤对管路的影响。实践证明改造是成功的,从而为山区企业供水系统的改造提供了一种全新的思路。 相似文献